MEGANE DRIVER’S HANDBOOK
RENAULT recommends ELF ELF has developed a complete range of lubricants for RENAULT: f engine oils f manual and automatic gearbox oils Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please refer to your maintenance document. Benefiting from the research applied to Formula 1, lubricants are very high-tech products.
Welcome to your new vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections Getting to know your vehicle ............................... 1 Driving ................................................................... 2 Your comfort . ........................................................ 3 Maintenance .......................................................... 4 Practical advice ..................................................... 5 Technical specifications . ..................................... 6 Alphabetical index .............
0.
Section 1: Getting to know your vehicle RENAULT cards: general information, use, deadlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic locking of opening elements when driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Headrests - Seats. . . . . . . . . . . . . . . . . . . . . . . . . . .
RENAULT cards: general information (1/2) The RENAULT card is used for: 1 1 2 3 4 5 2 3 4 5 Unlocking the doors and tailgate. Locking all doors and tailgate. Switching on the lighting remotely. Unlocking/locking the tailgate Integrated key. Special note The RENAULT “SERVICE” card, on equipped vehicles, can be identified by the word “SERVICE” engraved on the card. Refer to the information on the RENAULT “SERVICE” card in section 1. 1.
RENAULT cards: general information (2/2) Access to key 5 Press button 6 and pull on key 5 then release the button. 5 6 Using the key Refer to the information on “Locking/ unlocking the doors”. Once you have accessed the vehicle using the integrated key, replace it in its housing in the RENAULT card, then insert the RENAULT card into the card reader to start the vehicle.
Remote control RENAULT card: use 2 1 3 4 Unlocking the doors and tailgate Press button 1. The hazard warning lights flash once to indicate that the doors have been unlocked. When unlocking is only active for the driver’s door, (refer to the information on the “vehicle settings customisation menu” in Section 1): – pressing button 1 unlocks only the driver’s door and the fuel filler flap; – pressing button 1 twice unlocks all the doors and the tailgate.
Hands-free RENAULT card: use (1/3) 2 1 3 Use Unlocking the vehicle Note: ensure that the RENAULT card is not in contact with other electronic equipment (computer, PDA, phone, etc.) as this could hinder its operation. Pressing the button 3 also unlocks all the doors and the tailgate. On equipped vehicles, in addition to the functions of the remote control RENAULT card, it can be used to lock/ unlock without using the RENAULT card, when it is in access zone 1.
Hands-free RENAULT card: use (2/3) Locking using button 4 2 With the doors and luggage compartment closed, press button 4 on the driver’s door handle. The vehicle will lock. If a door or the tailgate is open or not closed properly, the vehicle will quickly lock/unlock. 4 1 Locking the vehicle There are three ways to lock the vehicle: remotely, using button 4, or using the RENAULT card.
Hands-free RENAULT card: use (3/3) 5 6 With the engine running, if after having opened and closed a door the card is no longer in the passenger compartment, the message Keycard not detected (accompanied by a beep when the speed exceeds a certain level) warns you that the card is no longer in the vehicle. This avoids you driving away after having dropped off a passenger who has the card, for example. The warning disappears when the card is detected again.
RENAULT card: deadlocking To deactivate deadlocking Unlock the vehicle using button 1 on the RENAULT card. 1 2 3 If the vehicle is equipped with a deadlocking function, this allows you to lock the opening elements and to prevent the doors from being unlocked using the interior handles (for example, by breaking the window and then trying to open the door from the inside).
RENAULT card “service” 1 Deactivation of the “SERVICE” mode 2 3 4 There are two possibilities: – Press a button on the RENAULT card (not the RENAULT “SERVICE” card); – start the engine with a RENAULT card (not the RENAULT “SERVICE” card). With the card in reader 4, press button 5. 5 If the vehicle is equipped with this card, it can be identified by the word “SERVICE” engraved on the card. In certain situations, you may wish to entrust your vehicle to a third party (parking valet, mechanic, etc.
Opening and closing the doors (1/2) Card reminder buzzer 1 2 When the driver’s door is opened and the card is still in the reader, the message “Please remove keycard” appears on the instrument panel, accompanied by a beep. Door/tailgate open buzzer Opening the doors from the outside With the doors unlocked or the “handsfree” RENAULT card in your possession, hold handle 1 and pull it towards you. In some cases, it may be necessary to pull the handle twice to open the door.
Opening and closing the doors (2/2) Safety of rear occupants The driver can authorise operation of the rear doors and, depending on the vehicle, the electric windows by pressing switch 1 on the side with the illustration. 1 Child safety Ç Vehicle with switch 1 Press switch 1 to authorise opening of the rear doors. If the vehicle is equipped with electric rear windows, this action will also authorise their use. The indicator light in the switch lights up to confirm that the locks have been activated.
Locking/unlocking the doors (1/2) Locking/Unlocking the doors from the outside This is done using the RENAULT Card; see the “RENAULT Card” information in Section 1. In certain cases, the RENAULT card may not work: – if the RENAULT card battery is weak, flat, etc. 3 A 1 2 – if equipment operating on the same frequency as the card (mobile phones, etc.) is used; – vehicle located in a high electromagnetic radiation zone.
Locking/unlocking the doors (2/2) 4 Locking the doors without the RENAULT card Door and tailgate status indicator For example, in the event of a discharged battery or the RENAULT card temporarily not working, etc. When the ignition is on, the indicator light integrated in switch 4 informs you of the status of the doors and tailgate: With the engine switched off and a door or tailgate open, press and hold switch 4 for more than five seconds.
Automatic locking when driving Operating faults You can decide whether you want to activate this function. 1 Operating principle After the vehicle is started, the system automatically locks the doors when you are driving at approximately 6 mph (10 km/h) and over. The door can be unlocked: – by pressing the door unlocking button 1. – by opening a front door (vehicle stationary). Note: if a door is opened or closed, it will automatically lock again when the vehicle reaches a speed of 6 mph (10 km/h).
Front headrests To adjust the angle of the headrest 2 1 Depending on the vehicle, tilt section A towards or away from you to the required position. A 3 To remove the headrest Raise the headrest to its highest position (tilt the seatback backwards if necessary). Press button 1 and lift the headrest to release it. To refit the headrest To raise the headrest Pull the headrest upwards to the desired height. To lower the headrest Press button 2 and guide the headrest down to the desired height.
Rear headrests 2 1 B A Position for use To refit the headrest Raise or lower the headrest while pulling it towards the front of the vehicle. Insert the headrest rods into the sleeves, and lower the headrest to the first notch. To remove the headrest Press tabs A of rods 1 and 2 simultaneously and remove the headrest. Note: on the three door version, first lower the bench seatback (refer to the information on the “Rear seat functions” in Section 3). 1.
Front seats with manual control (1/2) To tilt the seatback 3 Turn control knob 3 to the required position. Heated seats 2 (depending on vehicle) 1 4 To move the seat forwards or back Lift handle 1 to release. Release the handle once the seat is in the correct position and ensure that the seat is fully locked into position. To raise or lower the seat base Move lever 2 as many times as necessary upwards or downwards.
Front seats with manual control (2/2) 5 6 To adjust the lumbar support on the driver’s seat Lower handle 5 to increase the support and lift to decrease it. Table function Depending on the vehicle, the passenger seatback may be folded down onto the seat base to create a table. Lower the headrest, move the seat back, tilt handle 6 and completely lower the seatback. For your safety, attach any transported objects when the seat is in the table position. 1.
FRONT SEATS WITH ELECTRIC CONTROL Switch 3 is used for adjusting the seatback and switch 4 is used for adjusting the seat squab. On equipped vehicles, buttons 1 are used to store the chosen driving position (refer to the following page). 1 Adjusting the seat squab: Lower handle 5 to increase the support and lift to decrease it. For safety reasons, carry out any adjustments when the vehicle is not being driven. 5 3 – To move the seat forwards or back Move switch 4 forwards or backwards.
FRONT SEATS WITH ELECTRIC CONTROL with storage of settings Recalling a stored driving position It is possible to store three driving positions. A driving position includes the settings for the seat base and seatback of the driver’s seat. The system operates: 1 2 3 4 – with the “hands-free” card detected or, depending on the vehicle, RENAULT card in the card reader; – when the driver’s door is opened.
Access to rear seats, three-door version 1 1 2 3 4 Manually controlled seats Lift handle 1 and slide the seat forward. To return the seat to its original position, bring the seatback back into position. Do not move handle 1 and handle 2 or switch 4 at the same time.
Seat belts (1/3) Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in. Before starting, first adjust your driving position, then ask all occupants to adjust their seat belts to ensure optimum protection. Adjusting your driving position Make sure that the rear bench seat is locked in position correctly so that the rear seat belts will operate efficiently. Refer to the information on the “Rear bench seat” in Section 3.
Seat belts (2/3) ß Front seat belt reminder warning light This lights up on the central display when the engine is started then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approximately 12 mph (20 km/h), it flashes and a bleep sounds for around 2 minutes. 1 4 3 4 Locking Unwind the belt slowly and smoothly and ensure that buckle 3 locks into catch 4 (check that it is locked by pulling on buckle 3).
SEAT BELTS (3/3) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they are composed of: – seat belt inertia reel pretensioners; – Have the entire restraint system checked following an accident. – No operation whatsoever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. Anti-submarining air bag Located on each of the front seats, it deploys in order to prevent the occupant from sliding under the seat belt. Air bags for driver and front passenger Fitted to the driver and passenger side.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operation This system is only operational when the ignition is switched on. In a severe frontal impact, the air bags inflate rapidly, cushioning the impact of the driver’s head and chest against the steering wheel and the front passenger against the dashboard. The air bags then deflate immediately so that the passengers are not in any way hindered from leaving the vehicle.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
Methods of restraint in addition to the rear seat belts Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. – Have the entire restraint system checked following an accident. – No operation whatsoever is permitted on any part of the system (air bags, electronic control units, wiring) and the system components must not be reused on any other vehicle, even if identical.
Side protection devices Side air bags These air bags are fitted to the front seats and are activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Curtain air bags These are air bags fitted along the sides of the vehicle in the ceiling which trigger along the front and rear side windows to protect the passengers in case of a severe side impact.
Additional methods of restraint All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times.
Child safety: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.
Child safety: General information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to restrain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact. Before purchasing a child seat, check that it complies with the regulations for the country you are in and that it can be fitted in your vehicle.
Child safety: Choosing a child seat Rear-facing child seats A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell. 1.34 Forward-facing child seats The child’s head and abdomen need to be protected as a priority.
child safety: choosing a child seat mounting (1/2) There are two ways of attaching child seats: via the seat belt or using the ISOFIX system. Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected. Always check that the seat belt is correctly fastened by pulling it up, then pulling it out fully whilst pressing on the child seat.
child safety: choosing a child seat mounting (2/2) The ISOFIX anchorage points have been exclusively designed for child seats with the ISOFIX system. Never fit a different type of child seat, seat belt or other objects to these anchorage points. 1 2 The two rings 1 are located between the seatback and the seat base of the seat and are identified by a marking. To ensure your child seat can be easily fitted and locked on the rings 1, use access guides 2 on the child seat.
Child safety: fitting a child seat (1/11) Some seats are not suitable for fitting child seats. The diagram on the following page shows you how to attach a child seat. The types of child seats indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. Fit the child seat in a rear seat wherever possible. Check that when installing the child seat in the vehicle it is not at risk of coming loose from its base.
Child safety: fitting a child seat (2/11) The table below summarises the information already shown in the diagram on the following pages, to ensure the applicable regulations are respected.
Child safety: fitting a child seat (3/11) X=S eat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted.
Child safety: fitting a child seat (4/11) Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible.
Child safety: fitting a child seat (5/11) Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible.
Child safety: fitting a child seat (6/11) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
Child safety: fitting a child seat (7/11) X=S eat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted.
Child safety: fitting a child seat (8/11) Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located under the luggage compartment carpet and are indicated by a marking.
Child safety: fitting a child seat (9/11) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
Child safety: fitting a child seat (10/11) Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located under the luggage compartment carpet and are indicated by a marking.
Child safety: fitting a child seat (11/11) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
child safety: deactivating/activating the front passenger air bag (1/3) 1 DANGER 2 Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag. The child may suffer very serious injuries if the air bag is triggered. Deactivating the front passenger air bags To deactivate the air bags: with the vehicle stationary, push and turn lock 1 to the OFF position.
child safety: deactivating/activating the front passenger air bag (2/3) A A 3 The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag. The child may suffer very serious injuries if the air bag is triggered. 1.
child safety: deactivating/activating the front passenger air bag (3/3) 1 4 Activating the front passenger air bags Operating faults You should reactivate the air bag as soon as you remove the child seat from the front passenger seat to ensure the protection of the front passenger in the event of an impact. To reactivate the air bags: when the vehicle is stationary, push and turn lock 1 to the ON position.
Steering wheel/power-assisted steering Power-assisted steering Variable power-assisted steering The variable power-assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. 1 Height and reach adjustment Pull lever 1 and move the steering wheel to the required position. Then, push the lever back fully, beyond the point of resistance to lock the steering wheel. Make sure that the steering wheel is correctly locked.
Driving position: left-hand drive (1/2) 1 25 3 2 24 23 4 22 6 5 21 20 19 7 15 14 16 17 18 1.
Driving position: left-hand drive (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vent. 2 Side window demister outlet. 3 Stalk for: – direction indicator lights, – exterior lights, – front fog lights, – rear fog light. 4 Instrument panel. 5 Driver’s air bag and horn location. 6 – Steering column stalk for windscreen and rear screen wash/ wipe. – Trip computer information readout control and vehicle settings personalisation menu. 7 Centre air vents.
Driving position: right-hand drive (1/2) 1 2 4 3 25 24 23 22 21 20 19 17 1.
Driving position: right-hand drive (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vent. 2 Side window demister outlet. 3 Location for passenger air bag. 4 – Display (depending on the vehicle) for time, temperature, radio information, navigation system information, etc. – Driver and front passenger seat belt unfastened and passenger air bag deactivated warning lights 5 Centre air vents.
warning lights (1/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. A 1 The instrument panel A lights up when the ignition is switched on. You can adjust the brightness of the instrument panel by turning control knob 1. In some cases, the appearance of a warning light is accompanied by a message. The warning light © means you should drive very carefully to an authorised dealer as soon as possible.
warning lights (2/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Warning light © This lights up when the ignition A is switched on and goes out as soon as the engine is started. It can light up in conjunction with other indicator lights and/or messages on the instrument panel. It means you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.
warning lights (3/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. À A If it comes on when you are driving accompanied by the ® warning light and a beep, it is essential to stop and switch off the ignition. Check the oil level (refer to the information on “Engine oil level” in Section 4). If the level is normal, the light has come on for another reason: contact an authorised dealer.
warning lights (4/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. ß Front seat belt reminder warning light This lights up on the central display when starting the engine then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approximately 12 mph (20 km/h), it flashes and a bleep sounds for around 120 seconds.
displays and indicators (1/2) 1 3 2 a 6 Rev counter 1 (rpm × 1 000) 5 4 Engine oil level low warning When the engine is started, display 3 alerts the driver when the oil level is at its minimum. Refer to Section 4: “Engine oil level”. The first time the alert appears, it can be cleared by pressing one of the buttons on the end of stalk 2. Subsequent warnings will disappear automatically after 30 seconds. 1.
displays and indicators (2/2) 2 7 9 2 10 8 Speedometer 7 (mph or km/h) Overspeed buzzer Depending on the vehicle and country, a buzzer sounds for approximately 10 seconds every 40 seconds, as long as the vehicle is travelling in excess of 72 mph (120 km/h).
TRIP COMPUTER: general information (1/2) c) mileage before service; 1 d) tyre pressure monitor; 2 3 Trip computer and warning system 1 Display selection keys 2 and 3 Depending on the vehicle, this includes the following functions: Scroll through the following information upwards (button 2) or downwards (button 3) by pressing briefly and successively (the display depends on the vehicle equipment and country).
TRIP COMPUTER: general information (2/2) 2 3 Trip mileage resetting With “trip mileage recorder” selected on the display, press button 2 or 3 until the mileage recorder resets to zero. Resetting the journey parameters (reset button) With one of the journey parameters selected on the display, press button 2 or 3 until the display resets.
TRIP COMPUTER: trip settings (1/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101668 KM a) Total mileage and trip mileage recorder. 112. 4 KM FUEL USED 8.5 L Fuel used 20 L AVERAGE 7.2 L/100 1.64 b) Journey parameters. Fuel used. Fuel consumed since the last reset. Average Average fuel consumption since the last reset. 7.
TRIP COMPUTER: trip settings (2/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections CURRENT 9.4 L/100 Interpreting the display selected Current 9.4 L/100 RANGE 541 km Range 541 km DISTANCE 52.2 km Distance Current fuel consumption. This value is displayed above a speed of approximately 18 mph (30 km/h). Estimated range with remaining fuel.
TRIP COMPUTER: trip settings (3/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Oil change in 30000km/24 MONTHS Schedule Oil Chg in 100km Schedule Oil Chg in 10 days Interpreting the display selected c) Mileage before oil change.
TRIP COMPUTER: trip settings (4/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected FRONT TYRES 2.2 2.2 d) Tyre pressure monitor Refer to the information on the “Tyre pressure monitor” in Section 2. REAR TYRES 2.2 2.2 1.
TRIP COMPUTER: trip settings (5/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Settings menu: press and hold Interpreting the display selected e) Vehicle settings customisation menu. Enables certain vehicle functions to be set (instrument panel language, parking distance control, etc.). Refer to the information on “Vehicle settings customisation menu” in Section 1. f) Trip log.
TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpreting the display selected “Battery low start engine” Indicates that the vehicle must be started to recharge the battery (eg. after the engine has been switched off for some time whilst listening to the radio).
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The © warning light stays on. Examples of operating fault messages are given in the following pages.
TRIP COMPUTER AND WARNING SYSTEM: warning message These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
Vehicle settings customisation menu j) Parking sensor volume; k) Language. 1 2 3 On equipped vehicles, this function, which is integrated in the trip computer and warning system 1, allows you to activate/deactivate some of the vehicle’s functions. Accessing the settings customisation menu With the vehicle stationary, press either button 2 or 3 until the message “Settings menu: press and hold” appears on display 1. Press either button 2 or 3 for longer than 2 seconds to enter the menu. 1.
Clock and exterior temperature 1 2 Vehicles equipped with a navigation system, radio, etc. External temperature indicator For vehicles which are not fitted with buttons 2 and 3, refer to the specific equipment instructions to discover the special features. Special note: When the external temperature is between –3°C and +3°C, the °C characters flash (indicates risk of ice formation). 3 The time and, depending on the vehicle, the exterior temperature are displayed.
Rear view mirrors Folding door mirrors D 1 A B E C 3 2 The door mirrors automatically fold in when the vehicle is locked (switch 2 in position B). In this case, they will fold out when the ignition is next switched on. In any case, you can make the door mirrors fold in (switch 2 in position C) or fold out (switch 2 in position A). Automatic mode is then deactivated. To reactivate it, position switch 2 to B.
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. 2 One-touch mode 1 A Horn Press on the sides of the steering wheel boss A. Headlight flasher Pull stalk 1 towards you to flash the headlights. When driving, it is possible that the steering wheel may not be turned sufficiently to return the stalk automatically to its starting position.
Exterior lighting and signals (1/4) 1 2 3 1 Daytime running lights function Depending on the vehicle, the daytime running lights come on automatically when the engine is started. To activate or deactivate this function, refer to the information on the “Vehicle settings customisation menu” in Section 1. á Main beam headlights With the dipped beam headlights lit, pull stalk 1 towards you. This indicator light on the instrument panel comes on.
Exterior lighting and signals (2/4) Automatic main beam headlights This system switches the main beam headlights on and off automatically. The function uses a camera located behind the interior rear-view mirror to detect vehicles that are following and coming in the opposite direction. The main beam headlights come on automatically if: – exterior light is weak; – no other vehicles or lighting are detected; – the vehicle speed is above approximately 30 mph (45 km/h).
Exterior lighting and signals (3/4) 2 1 Directional headlights Depending on the vehicle, with the dipped beam headlights on and under certain conditions (speed, steering wheel angle, forwards gear selected, etc.) when cornering, the dipped beam headlights move to light the inside of the bend. Operating faults When the message “Check lighting”, accompanied by the © warning light is displayed on the instrument panel, there is a lighting fault. Consult an approved dealer. 1.
Exterior lighting and signals (4/4) g 1 5 Front fog lights Turn centre ring 5 on stalk 1 until the symbol faces mark 6, then release it. Operation of the fog lights depends on the exterior lighting position selected, and an indicator light will light up on the instrument panel. 6 Lights-on reminder buzzer If the lights are on after the engine is switched off, a warning beep sounds when the driver’s door is opened to warn you that the lights are still on.
Adjusting the headlight beam height Examples of positions for adjusting control A according to the load Five door Three door Driver alone or with front passenger 0 0 Driver with one front passenger and one rear passenger 0 0 Driver with one front passenger and two or three rear passengers 1 1 Driver with one front passenger, three rear passengers and luggage 3 3 A On vehicles fitted with this function, control A allows you to adjust the height of the beams according to the load.
WINDSCREEN WASH/WIPE (1/2) Vehicle fitted with front windscreen wiper rain sensor 1 1 E 2 A B D C F A park B automatic wiper function. When this position is selected, the system detects water on the windscreen and triggers the wipers at a suitable wiping speed.
WINDSCREEN WASH/WIPE (2/2) Headlight washers 1 Headlights on On equipped vehicles, hold stalk 1 pulled towards you for about 1 second, and the headlight washers and windscreen washers will be activated at the same time. 1 A Note: when the minimum windscreen washer fluid level is reached, the headlight washer system may be deprimed. Windscreen washer When working in the engine compartment, ensure that the windscreen wiper stalk is in position A (park). With the ignition on, pull stalk 1 then release.
REAR SCREEN WASH/WIPE 1 p With the ignition on, push the stalk. A 2 Y Rear screen washer/ wiper Rear screen wiper With the ignition on, turn ring A on stalk 1 to align the symbol with mark 2 then release it. To stop the operation, pivot ring A again. Wiping frequency varies with vehicle speed. Check the condition of the wiper blades.
Fuel tank (1/3) Fuel grade A Use a high-grade fuel that complies with the legislation in force in each country and which must conform to the specifications given on the label on the cover B. Refer to the information on “Engine specifications” in Section 6. B C Useable fuel tank capacity: 59 litres approximately. With the vehicle unlocked, to open the compartment B, place your finger into the recess C.
Fuel tank (2/3) Filling with fuel With the ignition off, insert the nozzle to open valve A and insert it fully before turning it on to fill the fuel tank (risk of splashing). Keep the nozzle in this position throughout the entire filling operation. When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts may be made, as there must be sufficient space in the fuel tank to allow for expansion.
Fuel tank (3/3) Vehicles without priming bulb 2 2 Put the ignition key in “Ignition On” (M) position and wait a few minutes before starting. This will enable the fuel circuit to be primed. If the engine does not start, repeat the procedure. Running out of fuel on diesel versions Vehicles with priming bulb 2 After a breakdown caused by completely running out of fuel, the system must be reprimed before the engine is restarted: Fill the tank with at least 8 litres of diesel fuel.
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stopping the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RUNNING IN Petrol version Diesel version Up to 600 miles (1,000 km), do not exceed 78 mph (130 km/h) in top gear or 3,000 to 3,500 rpm. For the first 900 miles (1,500 km), do not exceed 2,500 rpm. After completing this mileage you may drive faster, however, it is only after approximately 3600 miles (6,000 km) that you may reasonably expect full performance. You may only expect top performance from your vehicle after approximately 1,800 miles (3 000 km).
STARTING THE ENGINE (1/2) Starting vehicles with an automatic gearbox 1 The lever should be in position P. 2 For all vehicles: 3 Remote control RENAULT card When you get into the vehicle, insert the RENAULT card fully into card reader 2. To start, press button 1. If a gear is engaged, depress the clutch pedal to start the vehicle. Hands-free RENAULT card The RENAULT card must be inserted in card reader 2 or in detection zone 3. To start, depress the brake or clutch pedal and press button 1.
STARTING THE ENGINE (2/2) Operating faults 1 In certain cases, the hands-free RENAULT card may not work: 2 – when the RENAULT card battery is drained, flat battery, etc. – near to appliances operating on the same frequency as the card (monitor, mobile phone, video game, etc.); – vehicle located in a high electromagnetic radiation zone. The message “Please insert keycard” appears on the instrument panel. Insert the RENAULT card fully into card reader 2.
Stopping the engine Special note 1 2 If the card is no longer in the reader when you try to switch the engine off, the message “No keycard Press and hold” appears on the instrument panel: press button 1 for longer than two seconds. When you leave your vehicle, especially if you have your RENAULT card with you, check that the engine is completely switched off. Hands-free RENAULT card With the card in the vehicle, press button 1: the engine will stop.
Stop and Start function (1/3) This system enables a reduced fuel consumption and lower greenhouse gas emissions. The system is activated automatically when the vehicle is started. While driving, the system stops the engine (standby) when the vehicle is at a standstill (traffic jam, traffic lights, etc.) The message “Auto Stop” on the instrument panel indicates that the engine is on standby. The vehicle equipment remain operational while the engine is stopped.
Stop and Start function (2/3) Conditions preventing the standby of the engine Certain conditions prevent the system from using the engine standby function, including when: – reverse gear is engaged; – the bonnet is not locked; – the driver’s door is not closed; – the driver’s seatbelt is not fastened; – the outdoor temperature is too low or too high (less than around 0 °C or higher than around 30 °C); – the “Clear View” function is activated (please see “Automatic Climate Control” in Section 3); – t
Stop and Start function (3/3) The system is automatically reactivated each time the vehicle is started using the start button (please see “Starting, stopping the engine)”. 1 Operating faults When the message “Check Stop & Start” appears on the instrument panel and the integrated warning light 2 lights up on the switch 1, the system is deactivated. Please consult an authorised dealer. 2 Deactivating, activating the function Press 1 to deactivate the function.
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: – driving for long periods when the low fuel level warning light is lit; – using leaded petrol; – using fuel or lubrication additives which are not approved.
Special features of diesel versions Diesel engine speed Diesel engines are fitted with injection equipment which prevents the engine speed being exceeded irrespective of the gear selected. If the message “Check anti-pollution system” is displayed on the instrument Ä and panel accompanied by the © warning light; consult an approved dealer straight away.
Gear lever/Handbrake Handbrake To release: 1 Pull lever 2 up slightly, press button 3 and then lower the lever to the floor. 2 To apply: Pull the lever 2 upwards and make sure the vehicle is immobilised. 3 Make sure that the handbrake is properly released when driving (red indicator light off), otherwise overheating, or even damage, may occur.
ELECTRONIC PARKING BRAKE (1/3) Note: To indicate that the electronic parking brake is applied or released, a beep sounds and the message “Apply parking brake” appears on the instrument panel: 1 2 – with the engine running: when the driver’s door is opened; 3 – with the engine switched off (eg. when the engine stalls): when a front door is opened. In this case, pull and release switch 3 to apply the electronic parking brake.
ELECTRONIC PARKING BRAKE (2/3) Special cases 4 2 3 1 When parking on a slope or towing a trailer, pull switch 3 for a few seconds to obtain the maximum braking effect.
ELECTRONIC PARKING BRAKE (3/3) Versions with an automatic gearbox For safety reasons, automatic release is deactivated when the driver’s door is open or not shut properly and the engine is running (in order to prevent the vehicle from moving without the driver). The “Release parking brake manually” message appears on the instrument panel when the driver depresses the accelerator. Never leave your vehicle without moving the selector lever to position P or N.
Advice: antipollution, fuel economy and driving (1/3) Your vehicle complies with criteria for recycling and recovering vehicles at the end of their service life which will come into force in 2015. Some parts of your vehicle have therefore been designed to facilitate future recycling. These parts are easy to remove so that they can be recovered and reprocessed by recycling companies.
Advice: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring system – Sporty driving uses a lot of fuel: drive with a light right foot. – Brake as little as possible. If you anticipate an obstacle or bend in advance, you may then simply release the accelerator pedal. – Do not try to maintain the same speed up a hill, accelerate no more than you would on the level. Keep your foot in the same position on the accelerator pedal.
Advice: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air conditioning, it is normal to observe an increase in fuel consumption (especially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Environment Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. This commitment is illustrated by the Renault eco² signature. Emissions Manufacture Our vehicles are also equipped with a particle filter system including a catalytic converter, an oxygen sensor and an active carbon filter (the latter prevents vapour from the fuel tank being released into the open air).
Tyre pressure monitor (1/3) If the vehicle is equipped with the function, this system monitors the tyre pressure. 1 The tyre pressure can be adjusted when cold (refer to the information on “Tyre pressures”). If tyre pressures cannot be checked when the tyres are cold, the recommended pressures must be increased by 0.2 to 0.3 bar (3 PSI). 2 Operating principle Each wheel (except for the emergency spare wheel) has a sensor in the inflation valve which periodically measures the tyre pressure.
Tyre pressure monitor (2/3) 1 “Puncture” 2 Wheel F indicates that the wheel concerned is punctured or severely underinflated. Replace it or contact an approved dealer if it is punctured. Top up the tyre pressure if the wheel is deflated, E This message appears along with the ® warning light. F Display Display 1 on the instrument panel and trip computer and warning system 2 informs you of any tyre pressure faults (flat tyre, punctured tyre, system fault, etc.). 2.
Tyre pressure monitor (3/3) Emergency spare wheel If the vehicle is equipped with an emergency spare wheel, it will not have a sensor. When it is fitted to the vehicle, the message “Tyre pressure sensors absent” is displayed on the instrument panel. Tyre repair product and inflation kit Because the valves are specially designed, only use equipment approved by the approved network. Replacing wheels/tyres This system requires specific equipment (wheels, tyres, sensors, etc.).
Driver correction devices/aids (1/4) Depending on the vehicle, this is composed of: – the ABS (anti-lock braking system); – electronic stability control ESC with understeer control and traction control ASR ; – emergency brake assist with, depending on the vehicle, braking anticipation. These functions are an additional aid in the event of critical driving conditions, enabling the vehicle behaviour to be adapted to suit the driving conditions. However, the functions do not take the place of the driver.
Driver correction devices/aids (2/4) Hill start assistance This device assists the driver when starting on hills (ascending or descending). It prevents the vehicle from rolling forwards or backwards by automatically applying the brakes when the driver lifts their foot off the brake pedal to depress the accelerator pedal.
Driver correction devices/aids (3/4) Electronic stability control ESC with understeer control and traction control ASR Electronic stability control ESC This system helps you to keep control of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip on a bend, etc.). Operating principle A sensor in the steering wheel detects the direction selected by the driver. Other sensors throughout the vehicle measure the actual direction.
Driver correction devices/aids (4/4) The traction control ASR offers additional safety, it is recommended that you do not drive with the function disabled. Correct this as soon as possible by pressing switch 1 again. 1 Note: the function is reactivated automatically when the ignition is switched on or when a speed of approximately 24 mph (40 km/h) is exceeded. Emergency brake assist This system supplements the ABS and helps reduce vehicle stopping distances.
LANE DEPARTURE WARNING (1/2) This lane departure warning system notifies the driver when they accidentally cross a continuous or broken line. This function uses a camera attached to the windscreen, behind the rear-view mirror. – – – – – – This function is a driving aid in the event of the accidental crossing of a continuous or broken line in the road. However, the function is not intended to replace the driver.
LANE DEPARTURE WARNING (2/2) When a line is crossed and the indicators have not been activated, the function alerts the driver through warning light on the instrument panel, and a beep. 1 Activation Press button 1: the warning light on the 1 button lights up, accompanied by the message “Lane deviation warning on” and a beep.
Cruise control/speed limiter: speed limiter function (1/3) 6 1 2 5 3 The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. 4 Controls 1 Main “On/Off” switch. 2 Limit speed activation, storage and increase switch (+). 3 Decrease limit speed (-). 4 Switch the function to standby (with memorisation of the limit speed) (O). 5 Activation and recall of stored limit speed (R). 2.28 7 Switching on Press switch 1 on the side showing .
Cruise control/speed limiter: speed limiter function (2/3) C Varying the limit speed Exceeding the limit speed The limit speed may be changed by repeatedly pressing: It is possible to exceed the limit speed at any moment. To do this: press the accelerator pedal firmly and fully (beyond the kickdown point). – switch 2 (+) to increase the speed; – switch 3 (-) to decrease the speed. 2 5 3 While the speed is being exceeded, the limit speed flashes on the instrument panel and area C lights up red.
Cruise control/speed limiter: speed limiter function (3/3) 6 7 1 2 5 3 4 Putting the function on standby The speed limiter function is suspended when you press switch 4 (O). In this case, the limit speed will remain stored and is no longer displayed in zone 6 and the message “Memorised” along with the stored speed will appear on the display. Recalling the limit speed Switching off the function If a speed has been stored, it can be recalled by pressing switch 5 (R).
Cruise control/speed limiter: cruise control function (1/4) 1 The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 20 mph (30 km/h). 2 This function is an additional driving aid. However, the function does not take the place of the driver.
Cruise control/speed limiter: cruise control function (2/4) B C 5 2 3 Press switch 1 on the side showing . Indicator light 7 comes on, lit green, and the message “Cruise control” appears on the instrument panel and dashes appear in zone 6 to indicate that the cruise control function is activated and waiting to store a cruising speed. 4 Activating cruise control Driving At a steady speed (above 20 mph (30 km/h) approximately) press switch 2 (+): the speed is stored.
Cruise control/speed limiter: cruise control function (3/4) B Exceeding the cruising speed C 6 The cruising speed may be exceeded at any time by depressing the accelerator pedal. The cruising speed flashes on the instrument panel along with the illumination of zone C in red.
Cruise control/speed limiter: cruise control function (4/4) B C 7 A 1 5 2 3 4 Returning to the cruising speed If a speed is stored, it can be recalled, once you are sure that the road conditions are suitable (traffic, road surface, weather conditions, etc.). Press switch 5 (R) if the vehicle speed is above 20 mph (30 km/h). When recalling the stored speed zone A lights up to confirm activation. Zone B lights up as soon as the cruising speed is reached. 2.
PARKING DISTANCE CONTROL (1/3) Operating principle Ultrasonic detectors, installed in the front or rear bumper depending on the vehicle, measure the distance between the vehicle and an obstacle whilst reversing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 25 centimetres from the obstacle.
PARKING DISTANCE CONTROL (2/3) Automatic activation/deactivation of the rear parking distance control The system deactivates: – when the electronic parking brake is applied; – when the vehicle speed is above approximately 6 mph (10 km/h); – when the vehicle is stationary for more than approximately five seconds and an obstacle is detected (such as when in a traffic jam etc.); – when the vehicle is in neutral or when the gear lever has been shifted to N or P for automatic gearboxes.
PARKING DISTANCE CONTROL (3/3) Prolonged deactivation of the system 1 2 You may permanently activate or deactivate the front or rear parking distance control separately. From the vehicle settings customisation menu (refer to the information on the “Vehicle settings customisation menu” in Section 1), select the line “Front parking sensor” or “Rear parking sensor” then activate or deactivate the system: < = Special features Ensure that the ultrasonic sensors are not obscured (by dirt, mud, snow, etc.).
Reversing camera 1 2 C B A Fixed clearance gauge 2 The fixed clearance gauge comprises coloured markers A, B and C indicating the distance behind the vehicle: – A (red) approximately 50 centimetres from the vehicle; – B (yellow) approximately 1 metre from the vehicle; – C (green) approximately 2 to 3 metres from the vehicle; This gauge remains fixed and indicates the vehicle trajectory if the wheels are in line with the vehicle.
Automatic transmission (1/3) Driving in automatic mode 4 1 2 3 5 9 6 8 7 Selector lever 1 Operation Display 3 on the instrument panel shows the mode and gear selected. With the gear lever 1 in position P, switch on the ignition. 4: P: park 5: R: reverse gear 6: N: neutral 7: D: automatic mode 8 : manual mode 9: zone displaying gearbox mode or gear engaged in manual mode To move out of position P, you must depress the brake pedal before pressing unlocking button 2.
Automatic transmission (2/3) Driving in manual mode Special circumstances Parking the vehicle With the selector lever in position D, move the lever to the left. Shifting the lever repeatedly allows you to change gears manually: – If the road contours and bends do not allow you to stay in automatic mode (e.g.: in the mountains), we recommend that you change to manual mode. This will prevent the automatic gearbox from changing gears repeatedly when climbing, and permit engine braking on long descents.
Automatic transmission (3/3) Operating faults – When driving, if the message “Check auto gearbox” appears on the instrument panel, this indicates there is a fault. Contact your approved Dealer as soon as possible. – When driving, if the message “Auto gearbox overheating” appears on the instrument panel, stop the vehicle to allow the gearbox to cool down. 2 10 Contact your approved Dealer as soon as possible.
2.
Section 3: Your comfort Air vents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual air conditioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic climate control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR VENTS: air outlets (1/2) 3 1 4 5 6 2 7 9 Depending on the vehicle: 7 1 left-hand side air vent 2 left-hand side window demister outlet 3 windscreen demister outlets 4 centre air vents 5 right-hand side air vent 6 right-hand side window demister outlet 3.
AIR VENTS: air outlets (2/2) 1 2 1 4 3 2 Air flow Direction Turn control knob 1 (beyond the point of resistance). Right/left: move tabs 2 to the right or left. Up: maximum air flow. Up/down: lower or raise tabs 2. 2 To remove bad odours from your vehicles, only use the systems designed for this purpose. Consult an approved Dealer. Down: closed. Turn control knob 3 (beyond the point of resistance). To the right: maximum air flow. To the left: closed.
Manual air conditioning (1/2) 1 2 3 4 Distribution of air in the passenger compartment There are five air distribution options. Turn control 4 to choose the distribution option. W i The air flow is directed to the windscreen and the front side window demisting vents. The air flow is distributed between all the air vents, the front side window demisting vents, the windscreen demisting vents and the footwells.
Manual air conditioning (2/2) 1 2 3 4 “OFF" position: the system is deactivated: the ventilation speed for the passenger compartment air is zero (vehicle stationary), you can however still feel a slight flow of air when the vehicle is moving. Recommended demisting option: W Turn controls 1, 2 and 4 to the position. This is the quickest option for de-icing and demisting the side windows and the windscreen. Switching the air recirculation on 6 Press button 6: the integrated indicator light comes on.
automatic climate control (1/5) 2 1 3 6 13 11 10 1 and 6 Air temperature. 2, 3 and 4 Automatic programmes. 5 Distribution of air in the passenger compartment. 7 Off button. 8 Air conditioning. Automatic mode 5 12 The controls 3.6 4 9 8 7 9 De-icing/demisting of the rear screen and, depending on the vehicle, the door mirrors. 10 “Clear View” function. 11 Air recirculation. 12 Ventilation speed. 13 Display.
automatic climate control (2/5) 2 1 3 Clear View function 4 12 Press button 10: the integrated indicator light comes on. 6 This function quickly demists and deices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-icing functions must be activated. Press button 9 to stop the heated rear screen operating; the integrated indicator goes out.
automatic climate control (3/5) 3 The displayed temperature values show a comfort level. Switching air conditioning on or off In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions. Press switch 8 to switch off the air conditioning; the integrated indicator comes on and “AC OFF” is shown on the display 13. 13 8 When starting the engine, increasing or decreasing the value displayed will not allow the comfort level to be reached any more quickly.
automatic climate control (4/5) 5 W × The air flow is directed to the windscreen and the front side window demisting vents. The air flow is distributed between all the air vents, the front side window demisting vents, the windscreen demisting vents and the footwells. 12 ¿ ¾ ½ The air flow is directed mainly towards the footwells. The air flow is directed towards the dashboard vents and the footwells. Rear screen de-icing/ demisting 13 B Press button 9: the integrated indicator light comes on.
automatic climate control (5/5) Recycling 2 This function is managed automatically (operation is confirmed by warning light 14 on display 13), but you can also activate it manually. Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle; – air recirculation allows the external atmosphere to be cut off (when driving in polluted areas, etc.); – lowering the passenger compartment temperature as quickly as possible.
Air conditioning: information and advice on use Advice on use In some situations, (air conditioning off, air recirculation activated, ventilation speed at zero or low, etc.) you may notice that condensation starts to form on the windows and windscreen. If there is condensation, use the “Clear View” function to remove it, then use the air conditioning in automatic mode to stop it forming again. If the condensation does not clear, use the FAST programme. Note Presence of water under the vehicle.
Electric windows/Electric panoramic sunroof (1/3) These systems operate with the ignition on or off, until one of the front doors is opened (limited to about 3 minutes). Safety of rear occupants The driver can disable operation of the electric windows and, depending on the vehicle, the rear doors, by pressing switch 4. The indicator light integrated in the switch lights up to confirm that the locks have been activated.
Electric windows/Electric panoramic sunroof (2/3) Special note 7 0 A B C Your vehicle is equipped with an antipinch facility: when the sunroof encounters resistance whilst closing, (somebody’s fingers, etc.) it stops and then moves back several centimetres. D 9 Sun blind Sunroof – to open: push handle 7 upwards and guide the blind as it retracts; – Open the sun blind – to close: pull handle 7 until it clicks into the catch.
Electric windows/Electric panoramic sunroof (3/3) Remote control window closing (for vehicles with one-touch windows on all windows). When you lock the doors from the outside, press the locking button on the RENAULT card twice in quick succession, or on the driver's door in hands-free mode, and all the windows will close automatically. It is recommended that the user only operates the system when the vehicle can be seen clearly and no one is inside.
MANUAL WINDOW WINDERS/Interior lighting (1/2) 2 3 4 1 5 Manual window winders Courtesy light Front door lights Turn handle 1. Tilt switch 3 to move it to the position for: Light 5 comes on when the door is opened. – permanent lighting; – intermittent lighting, which comes on when a door is opened. This switches off after a time delay, once the doors concerned have been closed correctly; – immediate switching off. Map reading lights (depending on vehicle) Tilt switches 2 or 4.
Interior lighting (2/2)/SUN VISOR 6 7 8 9 Glove box light 6 Sun visor Luggage compartment light 9 Light 6 comes on when the cover is opened. Lower the sun visor 7 over the windscreen or unclip it and turn it over the side window. Depending on the vehicle, light 9, comes on when the luggage compartment is opened. Courtesy mirrors Slide cover 8, depending on the vehicle, and the mirror is lit. 3.
Passenger compartment storage space and fittings (1/4) 3 1 Door pockets 1 2 Driver and passenger underfloor storage compartments 2 Sun visor storage 3 This can be used for storing motorway tickets, cards, etc. This storage compartment can be used to hold the vehicle documentation, etc. Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passengers during sudden turning, braking or in the event of an accident.
Passenger compartment storage space and fittings (2/4) 4 5 6 A 7 Front centre armrest storage compartment A Centre console storage compartments 6 Press button 4 and lift the cover 5. Passenger storage compartment Pull handle 7 to open it. The glove box can hold A4-size documents, a large bottle of water, etc. The storage compartment is ventilated and refrigerated.
Passenger compartment storage space and fittings (3/4) 10 11 9 8 12 Door pockets 8 Storage compartment 9 Rear armrest storage Lower armrest 12 and, depending on the vehicle, lift cover 11 using unlocking handle 10. 3.
Passenger compartment storage space and fittings (4/4) 15 14 16 13 Clothes hooks 13 Grab handle 14 Front seat storage compartments 15 Rear centre console storage compartments 16 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle. Depending on the vehicle, storage compartment 16 may be replaced by air vents; refer to Section 3 “Air vents”. 3.
Ashtray, cigar lighter, accessories socket 1 3 2 2 Accessories sockets Cigar lighter 1 Ashtray 2 You may use cigar lighter recess 1 or socket 3 (depending on the vehicle). They are designed for connecting accessories with a maximum power rating of 120 Watts (voltage: 12V) which have been approved by our Technical Department. With the ignition on, push in cigar lighter 1, it will spring back with a click when it is ready. Pull it out to use. After use, replace it without pushing it all the way in.
REAR BENCH SEAT functions (1/3) 1 Sport tourer versions Depending on the vehicle, seatback A can be folded down on its own to allow long or bulky objects to be transported. 2 3 To fold down the seatback Ensure that the front seats are far enough forward. A Press button 1 seatback(s) A. and lower the Lower the rear headrests (refer to the information on the “Rear headrests” in Section 1). Place the seat belts 2 in their guides 3.
REAR BENCH SEAT functions (2/3) 4 6 6 5 Luggage compartment carpet level adjustment To adjust the level of the luggage compartment carpet in line with the seatbacks, lift carpet 4 via the rear door; height adjuster 5 is deployed automatically. Fit the luggage compartment carpet and unfold blanking covers 6. When refitting the bench seat, push the booster seat in at the same time as fitting the luggage compartment carpet. When refitting the seatback, make sure it is correctly locked in place.
REAR BENCH SEAT functions (3/3) 1 B C When moving the rear bench seat, ensure that nothing obstructs the anchorage points (part of the body, a pet, gravel, cloth, toys, etc.). The seat and the seatback may be folded away to allow bulky objects to be carried. To fold away the seat base Tilt seat base B against the front seats. To fold down the seatback After folding the seat base down, remove the rear headrests (refer to the section on “rear headrests”) then press button 1 and lower the seatback(s) C.
Tailgate 2 3 1 Press button 1 and lift the tailgate. Opening manually from inside the vehicle To close Special note: Pull down the tailgate using handle 2 inside the tailgate to assist you. If it is impossible to unlock the tailgate, it can be done from inside. To open – access the luggage compartment by folding forward the seatback(s) of the rear bench seat, – insert a pencil or similar object in cavity 3 and slide the unit as shown in the illustration, – push the tailgate to open it. 3.
REAR PARCEL SHELF 1 3 2 Removal Unhook the two cords 1 (tailgate side). Lift rear parcel shelf 2 slightly and pull it towards you. To refit it, proceed in reverse order to removal. Do not place any objects, especially heavy or hard objects, on the parcel shelf. These may pose a risk to the vehicle occupants if the driver has to brake suddenly or if the vehicle is involved in an accident. 3.
LUGGAGE COMPARTMENT COVER: sport tourer versions (1/2) B 1 A To remove the flexible section of the luggage cover Pull handle 1 gently to release the pins from their mounting points located on each side of the luggage compartment. Guide the luggage cover onto the roller. Removing the luggage cover Push the luggage compartment cover to the left (movement A) and lift the right-hand side of the inertia reel (movement B).
LUGGAGE COMPARTMENT COVER: sport tourer versions (2/2) 4 3 2 6 5 Luggage compartment cover storage From the rear doors, lower the bench seat seatback (refer to information on the “Rear bench seat” in section 3). Lift the luggage compartment carpet 2 and secure it by attaching straps 3 onto hooks 4. 3.28 Store luggage compartment cover 6 behind the booster seat 5 in the dedicated storage compartment.
Luggage compartment storage space and fittings (1/3) A 1 2 2 3 Storage under carpet 1 Anchorage points To open, fold back carpet A. Hooks 2 located on each corner of the luggage compartment, allow the load to be secured. (depending on vehicle) (Three- and five-seater versions) Side straps Side straps 3 are located either side of the luggage compartment, and can be used to store an oil can.
Luggage compartment storage space and fittings (2/3) 7 5 4 B 6 Anchorage points Storage under carpet Hooks 5, located on either side of the luggage compartment, allow the load to be secured. To access storage compartments 7, fold back section B using handle 4 and, depending on the vehicle, lift flap 6. (sport tourer version) 3.
Luggage compartment storage space and fittings (3/3) 8 4 C Separating the luggage compartment 9 C On the back there is an elastic strip 9 to hold small objects vertically in position. (sport tourer version) The loading area can be separated. Turn locks 8 situated on either side of the luggage compartment to the first notch. Lift divider C using handle 4; when the bolts make contact, push the divider and it will lock. Maximum weight: 20 kg.
Transporting objects in the luggage compartment/Towing (towing equipment) A Always place the objects to be transported so that their largest side rests against the back of the rear bench seat, for normal loads (Example A), or against the back of the front seats when the rear bench seatbacks are folded down. If you have to place objects on the folded seat back, it is vital that you remove the headrests before folding the seat back so that it can be folded as flat as possible against the seat. 3.
TRANSPORTING OBJECTS: luggage net (1/2) Fitting the luggage net behind the front seats 1 A Inside the vehicle on each side: – lift cover 1 to access the upper mounting ring of the net; – fix the net belt hook onto the ring; 2 Luggage net A – to access the lower mounting 2 for the net the first time you use it, contact an approved Dealer; On equipped vehicles, this can be used when transporting animals or luggage, to separate them from the passenger section.
TRANSPORTING OBJECTS: luggage net (2/2) 3 A – in the luggage compartment, fix the lower mounting strap hook on the net to the anchorage point 4 located under the luggage compartment carpet; – adjust the net strap so that it is taut. 4 Fitting the luggage net behind the rear bench seat Inside the vehicle on each side: – Lift cover 3 to access the upper mounting ring of the net; – fix the net belt hook onto the ring; The luggage net must not be used to restrain or hold objects. Risk of injury. 3.
ROOF BARS: access to fixing points Three door version 1 Sport tourer versions The fitting of roof bars is prohibited on three door versions. For vehicles fitted with original roof bars, the roof bars are fixed and must not be removed. To change them contact an approved Dealer. Five-seater and sport tourer versions Open the doors to access the mounting points 1.
multimedia equipment Navigation system The equipment described below may or may not be fitted to the vehicle, and its location may vary, depending on the vehicle navigation system version. 1 Radio; 2 CD or DVD reader; 3 Central control; 4 Steering column control; 5 Micro. 1 3 2 Hands-free telephone integrated control On equipped vehicles, use microphone 5 and steering column control 4.
Section 4: Maintenance Bonnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . general information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . topping up, filling . . . . . . . . . . . . . . . .
Bonnet Closing the bonnet 2 Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and guide it down, allowing a 30 cm gap before it is closed, then release it. It will latch automatically under its own weight. 1 To open, pull handle 1, located on the left-hand side of the dashboard. Unlocking the bonnet catch To release it, lift tab 2. Opening the bonnet Lift the bonnet; you will need to guide it as it is held by a strut.
Engine oil level: general information (1/2) It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level between oil changes. However, contact your approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period. Oil change frequency: check the oil level from time to time and certainly before any long journey to avoid the risk of damaging your engine.
Engine oil level: general information (2/2) A B Maximum engine oil level exceeded. C B A The oil level should only be read with the dipstick as explained above. If the oil level exceeds the maximum level, do not start your vehicle and contact an approved Dealer. Consult your approved Dealer at once if you notice an abnormal or repeated drop in any of the fluid levels.
Engine oil level: topping up, filling (1/3) 1 1 1 2 Topping up/filling The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day). Engine oil grade Refer to the Maintenance Service Booklet for your vehicle. Do not exceed the max level and do not forget to refit cap 1 and dipstick 2.
Engine oil level: topping up, filling (2/3) 2 1 1 1 Topping up/filling The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day). Engine oil grade Refer to the Maintenance Service Booklet for your vehicle. Do not exceed the max level and do not forget to refit cap 1 and dipstick 2. 4.
Engine oil level: topping up, filling (3/3)/OIL CHANGE Oil change Service interval: refer to the Maintenance Service Booklet for your vehicle. Average capacities for oil change including oil filter (for information) Engine 1,2 TCe: 4.5 litres 1.4 TCe engine: 4.5 litres 1,6 16V engine: 5.1 litres 2.0 16V engine: 4.4 litres 2.0 T engine : 5.4 litres 1.5 dCi engine : 4.5 litres 1.9 dCi engine: 5.1 litres 2.0 dCi engine: 7.4 litres Engine oil grade Refer to the Maintenance Service Booklet for your vehicle.
Levels (1/3) 1 Checking intervals Replacement intervals Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). Refer to the Maintenance Service Booklet for your vehicle. If the level needs to be topped up, only use products approved by our Technical Department which ensure: – protection against freezing; – anticorrosion protection of the cooling system.
Levels (2/3) 1 Level 1 Topping up It is normal for the level to drop as the linings become worn, but it should never drop below the MIN line. After any operation on the hydraulic circuit, a specialist must replace the fluid. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking procedure from our network or from the manufacturer’s website. Only use fluids approved by our Technical Department (and taken from a sealed container).
Levels (3/3)Filters Liquid Screen wash product (product with antifreeze in winter). 1 Windscreen/headlight washer reservoir Topping up With the engine switched off, open cap 1, fill until you can see the fluid, then refit the cap. NOTE Depending on the vehicle, to find out the fluid level, open cap 1 and pull out the dipstick. 4.10 Jets Use a tool such as a needle to adjust the height of the windscreen washer jets.
Tyre pressure A Tyre safety and use of snow chains A B C E H The tyre pressure is indicated on label A affixed to the edge of the driver’s door. Open the door to read it. B: dimension of the tyres fitted to the vehicle. C: tyre pressures for the front wheels (non-motorway). D F G F: tyre pressures for the rear wheels (motorway). G: tyre pressure for the emergency spare wheel. H: emergency spare wheel tyre dimension if different to the four tyres fitted to the vehicle.
Battery 1 Depending on the vehicle, a system continuously checks the battery charge status. If the level drops, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine. Then the message “Battery charging” appears on the instrument panel for the duration of the charging time.
Bodywork maintenance (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the exterior of the vehicle regularly. Protection against the effects of corrosive agents Although your vehicle has been treated with very effective anti-corrosion products, it nevertheless remains subject to the effects of different parameters.
Bodywork maintenance (2/2) You should Observe the vehicle stopping distances when driving on gravelled surfaces to prevent paint damage. Repair, or have repaired quickly, areas where the paint has been damaged, to prevent corrosion spreading. Remember to visit the body shop periodically in order to maintain your anti-corrosion warranty. Refer to the Maintenance Service Booklet. Respect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway).
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the interior of the vehicle regularly. A stain should always be dealt with swiftly. Whatever type of stain is on the trim, use cold (or warm) soapy water with natural soap. Detergents (washing-up liquid, powdered products, alcohol-based products) should not be used. Use a soft cloth. Rinse and soak up the excess. Glass instrument panel (e.g.
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable equipment originally fitted in the vehicle If you need to remove equipment in order to clean the passenger compartment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driver’s mat should be fitted on the driver’s side, etc.) and fit them with the components supplied with the equipment (for example, the driver mat should always be fixed using the pre-fitted mounting components).
Section 5: Practical advice Puncture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tool kit (jack, wheelbrace, etc.). . .
Puncture, emergency spare wheel In the event of a puncture, depending on the vehicle, you will have: An emergency spare wheel or tyre inflation kit (refer to the information on the following pages). 1 Emergency spare wheel Special note: The Tyre Pressure Monitor function does not check the emergency spare wheel (the wheel replaced by the emergency spare wheel disappears from the instrument panel display). Refer to the information on the “Tyre pressure monitor” in Section 2.
TYRE PRESSURE KIT (1/3) B A Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE PRESSURE KIT (2/3) 1 2 3 Depending on the vehicle, remove the central partition in the storage compartment to access the inflation kit. 4 Open the kit, remove caps 1 and 3 (the cap must not be removed from the bottle) then screw bottle 2 to its base 3. 5 With the engine running and the parking brake applied, 6 8 If a minimum pressure of 1.8 bar is not reached after 15 minutes, repair is not possible; do not drive the vehicle but contact an approved dealer.
TYRE PRESSURE KIT (3/3) – affix driving recommendation label 9 to the dashboard where it can easily be seen by the driver; – store the kit; 9 8 Once the tyre is inflated correctly: – stop using the kit; – close the integrated cap on the bottle again; – disconnect adapter 8; Nothing should be placed around the driver’s feet as such objects may slide under the pedals during sudden braking manoeuvres and obstruct their use.
TOOL KIT/WHEEL TRIM – WHEEL Wheelbrace 1 2 Jack 2 When replacing the jack, fold it correctly and position the wheelbrace correctly before replacing it in its position. 1 3 4 5 The tool kit is located in the luggage compartment: lift the carpet. Hubcap tool 3 This tool is used to remove the wheel trims. Wheel bolt guide 4 To finish loosening or starting to tighten the wheel bolts. Towing hitch 5 Refer to the information on “Towing” in Section 5. The tools included in the tool kit depend on the vehicle.
Changing a wheel (1/2) 3 Vehicles equipped with a jack and wheelbrace If necessary, remove the wheel trim. 1 2 Use the wheelbrace 3 to slacken off the wheel bolts. Position it so as to be able to push from above. Offer up the jack 4 horizontally; the jack head must be lined up with jacking point 1 located on the underside of the sill, closest to the wheel concerned, as shown by arrow 2. Start cranking the jack up by hand to align the base plate (which should be pushed slightly under the vehicle).
CHANGING A WHEEL (2/2) Undo the bolts and take off the wheel. Fit the emergency spare wheel onto the hub and rotate it until the mounting holes in the wheel coincide with those of the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel. Tighten the bolts, checking that the wheel is correctly positioned on its hub and lower the jack.
Tyres (1/3) Tyre and wheel safety The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. 2 You must make sure that your tyres conform to local road traffic regulations. 1 When the tyre tread has been worn to the level of the wear indicators, they become visible 2: it is then necessary to replace your tyres because the tread rubber is no more than 1.6 mm deep, resulting in poor roadholding on wet roads.
Tyres (2/3) Tyre pressures Adhere to the tyre pressures (including the emergency spare wheel). The tyre pressures should be checked at least once a month and additionally before any long journey (refer to the label affixed to the edge of the driver’s door). Pressures should be checked when the tyres are cold; ignore higher pressures which may be reached in hot weather or following a fast journey. If tyre pressures cannot be checked when the tyres are cold, the normal pressures must be increased by 0.
Tyres (3/3) Use in winter Chains For safety reasons, fitting snow chains to the rear axle is strictly forbidden. Chains cannot be fitted to tyres which are larger than those originally fitted to the vehicle. Studded tyres This type of equipment may only be used for a limited period and as laid down by local legislation. It is necessary to observe the speed specified by current legislation. These tyres must, at a minimum, be fitted to the two front wheels.
Front headlights: changing bulbs (1/3) A 1 After opening the bonnet, pull tool A upwards. Remove the two screws 1 from the headlight using the tool. Pull the headlight forwards, sliding it in its rails up to the end stop. After refitting the light, tighten the screws 1 and reposition the tool correctly in its housing. Direction indicator lights B C D E Dipped beams Halogen dipped beam headlight Unlock the two springs D, remove the cover, then unclip the spring 3 to remove the bulb 4. Bulb type: H7.
Front headlights: changing bulbs (2/3) B C D E B 2 3 4 5 6 Daytime running light Front side light Remove the cover C, unlock the bulb holder 2 by rotating it. Bulb type: P21W. Remove the cover E and pull the bulb holder 6. Main beam headlight Remove the cover E, press the bulb holder 5 downwards to unlock it. Bulb type: W5W. To comply with current legislation, or as a precaution, you can obtain an emergency kit from an approved dealer containing a set of spare bulbs and fuses.
Front headlights: changing bulbs (3/3) Additional lights If you wish to fit fog lights or long range headlights to your vehicle, consult an approved Dealer. 7 8 Daytime running lights 7 Please see an authorised dealer. Front fog lights 8 The front bumper needs to be removed; consult an approved Dealer. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (1/6) 5 A 1 2 3 B 6 4 Five-door versions Direction indicator lights/brake and side lights – Unclip the cover to access nuts 1 and 2; – unscrew nut 2 without removing it completely; Direction indicator lights 5 – loosen nut 1, press down on it to release the front of the light (movement A) then remove the nut; Bulb type: PY21W. – from the outside, pull the light towards you (movement B); Bulb type: P21/5W.
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (2/6) 9 10 8 11 7 Five-door versions (continued) Fog lights/side lights and reversing lights – From the luggage compartment, unclip flap 7, then remove the bolts 8. 5.16 – Lower the tailgate, then pull light 9 towards the rear to release it. Reversing light 10 – Unscrew the bulb holder for the bulb concerned. Fog light/side light 11 Bulb type: W16W. Bulb type: P21/4W.
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (3/6) 13 14 12 17 16 15 Three-door versions – Unclip the access flap; 16 Side light/stop light Bulb type: P21/5W. – unscrew nuts 12 and 13; 17 Direction indicator light – from the outside, remove bolt 14, then pull on the light; 18 Reversing light – remove the bulb holder by releasing the clips 15; 18 Bulb type: PY21W. Bulb type: P21W.
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (4/6) 21 22 23 C 24 20 Sport tourer Versions Side light 22 Side lights/reversing lights and fog lights Reversing light 23 – From the luggage compartment, unclip flap 20 (movement C), then remove the bolts . – Lower the tailgate, then pull light 21 towards the rear to release it. – Turn the bulb holder of the bulb concerned a quarter of a turn. Bulb type: W5W. Bulb type: P21W. Fog light 24 Bulb type: H21W.
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (5/6) 26 28 27 25 Estate versions Side light and brake light 28 Brake and side lights/direction indicator lights Direction indicator lights 29 (continued) – Unclip covers 25 to access the nuts; 29 Bulb type: P21/5W. Bulb type: PY21W. – unscrew the 2 nuts; – from the outside, pull the light towards you; – remove the bulb holder 27 by releasing the clips 26. 5.
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (6/6) 31 32 30 D 22 23 33 High level brake light 30 Number plate lights 32 Indicator lights 33 Consult an approved Dealer. – Unclip light 32 by pressing tab 31; – Unclip indicator light 33 (using a flat-blade screwdriver type tool positioned at D to move the indicator light towards the front of the vehicle); – remove the light cover to gain access to the bulb. Bulb type: W5W. – turn the bulb holder a quarter of a turn and take out the bulb.
INTERIOR LIGHTING: changing bulbs (1/2) 1 B 2 A 3 4 Courtesy light Door lights Glove box light – Position the 3 switches in the central position; Unclip light 2 (using a flat-blade screwdriver or similar). Open the access cover 3, you can then unclip the bulb holder more easily 4. – move the courtesy light backwards (movement A) then tilt the front downwards (movement B); Turn the bulb holder a quarter of a turn and take out the bulb. Bulb type: C5W.
INTERIOR LIGHTING: changing bulbs (2/2) 6 7 8 5 Luggage compartment light Unclip the light at 5 using a flat-blade screwdriver or similar. Disconnect the light. Press tab 6 to release lens 8 and access bulb 7. Bulb type: W5W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
FUSES (1/2) A 1 B Fuse box Tweezers 1 If any electrical component does not work, check the condition of the fuses. Remove the fuse using tweezers 1, located at the back of flap A or B. Unclip cover A or B (depending on vehicle). In accordance with local legislation or as a precautionary measure: Check the fuse in question and replace it, if necessary, by a fuse of the same rating.
FUSES (2/2) 3 7 10 14 4 8 11 15 1 5 9 12 16 2 6 13 17 C 18 19 Allocation of fuses (the presence of certain fuses depends on the vehicle equipment level) 1 Electronic parking brake; 2 Brake lights; 3 Automatic door locking; 4 Driver’s electric window; 5 Passenger compartment unit; 6 Direction indicator lights; 7 Navigation system; 8 Interior rear-view mirror; 9 Rear screen wiper; 10 and 11 Rear electric windows; 12 ABS/ESP; 13 Passenger electric window; 14 Windscreen washer; 15 Heated do
Battery: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any electrical consumers (courtesy lights, etc.) are switched off before disconnecting or reconnecting the battery. The battery charger must be compatible with a battery with nominal voltage of 12 volts. – When charging, stop the charger before connecting or disconnecting the battery. Do not disconnect the battery when the engine is running.
Battery: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle 1 If you have to use the battery from another vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you already have jump leads, ensure that they are in perfect condition. The two batteries must have an identical nominal voltage of 12 volts.
RENAULT card: battery 2 A B 4 1 Replacing the battery When the message “Low card battery” appears on the instrument panel, replace the RENAULTcard battery, press button 1, pulling on emergency key 2, then unclip cover 3 using tab 4. Remove the battery by pressing on one side (movement A) and by lifting the other (movement B) then replace it, ensuring the polarity and model, shown on cover 3 are respected.
Fitting a radio 2 1 3 If your vehicle is not fitted with an audio system, one can be fitted and locations have been provided for: – the radio 1; – tweeter speakers 2; – bass speakers 3. To install any equipment, please consult an approved dealer. Radio location 1 Unclip the blanking cover. The aerial, + and – supply and speaker wire connections are located behind it. 5.28 – In all cases, it is very important to follow the manufacturer’s instructions carefully.
ACCESSORIES Before fitting an electrical or electronic device (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle. If you are using an anti-theft device, only attach it to the brake pedal. Contact an approved dealer for this information. Electrical and electronic accessories – Connect accessories with a maximum power of 120 Watts only. Use of transmission/ receiving devices (telephones, CB equipment etc.
WINDSCREEN WIPER BLADES 1 B A 4 2 C 5 3 6 Replacing windscreen wiper blades 1 Rear screen wiper blade 4 With the ignition on and engine switched off, lower the windscreen wiper stalk completely: they stop slightly away from the bonnet. Lift wiper arm 3, pull tab 2 (movement A) and push the blade upwards. – pivot blade 4 until some resistance is met (movement C); To refit Slide the blade along the arm until it clips on. Make sure that the blade is correctly locked in position.
Towing: breakdown (1/2) Before towing, unlock the steering column: with the clutch depressed, engage first gear (lever in position N or R for vehicles with automatic transmissions), insert the RENAULT card in the card reader then press the engine start button for two seconds.
Towing: breakdown (2/2) – Use a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed must be able to brake. 3 5 4 6 7 4 Only use the front 3 and rear 6 towing points (never use the drive shafts or any other part of the vehicle). These towing points may only be used for towing: never use them for lifting the vehicle directly or indirectly. Access to towing points – A vehicle must not be towed if it is not fit to be driven.
Operating faults (1/5) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or unlock the doors. Card battery is flat. Replace the battery. You can still lock/ unlock and start your vehicle (refer to the information on “Locking/unlocking the doors” in Section 1 and “Starting/Stopping the engine” in Section 2).
Operating faults (2/5) The starter is activated POSSIBLE CAUSES WHAT TO DO The instrument panel indicator lights are weak or fail to light up and the starter does not turn. Battery terminals not tight, battery terminals disconnected or oxidised. Retighten or reconnect the terminals, or clean them if they are oxidised. Discharged battery or not operational. Connect another battery to the faulty battery.
Operating faults (3/5) On the road POSSIBLE CAUSES WHAT TO DO The steering column remains locked. Steering wheel locked. Move the steering wheel while pressing the engine start button (refer to the information on “Starting the engine” in Section 2). Coolant boiling in the coolant reservoir. Mechanical fault: damaged cylinder head gasket. Stop the engine. Contact an approved dealer. Smoke under the bonnet. Short-circuit or cooling system leak.
Operating faults (4/5) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine overheats. The coolant temperature indicator is in the warning zone and warning light ® comes on. Engine cooling fan not working. Stop the vehicle, switch off the engine and contact an approved dealer. Coolant leaks. Check the coolant reservoir: it should contain fluid. If there is no coolant, consult an approved dealer as soon as possible.
Operating faults (5/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. The wiper does not stop. Faulty electrical controls. Consult an approved dealer. Direction indicators flashing more quickly. Blown bulb. Front: contact an approved dealer. The direction indicators do not work. Faulty electrical circuit. Consult an approved dealer.
5.
Section 6: Technical specifications Vehicle identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.2 Engine identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3 Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5 Engine specifications. . .
Vehicle identification plates A 1 2 3 4 5 A The information shown on the vehicle identification plate should be quoted on all correspondence or orders. The presence and location of the information depends on the vehicle. Vehicle identification plate A B 6.2 1 Vehicle type and chassis number. Depending on the vehicle, this information is also given on marking B. 2 MMAC (Maximum permissible all-up weight). 6 7 8 9 10 11 12 13 3 GTW (Gross train weight – vehicle fully loaded, with trailer).
Engine identification plates (1/2) A 1 2 A 3 A Quote the information on the identification plate or label A in all correspondence or when ordering parts. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. A A 6.
Engine identification plates (2/2) A 1 2 A 3 A Quote the information on the identification plate or label A in all correspondence or when ordering parts. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. A A 6.
Dimensions (in metres) (1/3) Three door version 0.862 2.640 0.797 1.546 4.299 1.423* 1.547 1.785 * Unladen 6.
Dimensions (in metres) (2/3) Five door version 0.862 2.641 0.792 1.546 4.292 1.471* 1.547 1.808 * Unladen 6.
Dimensions (in metres) (3/3) Sport tourer versions 0.862 2.703 0.994 1.546 4.558 1.461* 1.547 1.766 * Unladen 6.
Engine specifications Versions Engine type (see engine plate) Cubic capacity (cc) Type of fuel Octane Rating Spark plugs 6.8 1.2 TCe 1.4 TCe 1.6 16V 2.0 16V 2.0 T 1.5 dCi 1.9 dCi 2.0 dCi H5F Turbo H4J Turbo K4M M4R F4R Turbo K9K F9Q M9R 1 197 1,395 1,598 1,998 1,998 1,461 1,870 1,995 It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap.
WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer.
Replacement parts and repairs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
service sheets (1/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (2/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (3/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (4/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (5/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (6/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
Anticorrosion check (1/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (2/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (3/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (4/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (5/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (6/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Alphabetical index (1/5) A ABS...............................................................1.57, 2.22 → 2.25 access to the rear seats..................................................... 1.21 accessories........................................................................ 5.29 accessories socket............................................................. 3.21 additional methods of restraint......................1.25 → 1.28, 1.31 side protection..........................................................
Alphabetical index (2/5) driving.......... 2.2 – 2.4, 2.9 → 2.17, 2.19 → 2.25, 2.28 → 2.37, 2.39 → 2.41 driving position settings.............................................................1.22 → 1.24 E electric beam height adjustment......................................... 1.80 electric windows.....................................................3.12 → 3.14 electronic parking brake.........................................2.12 → 2.14 Electronic Stability Program: ESP..........................2.22 → 2.
Alphabetical index (3/5) horn: flash.............................................................................. 1.75 sounding the horn......................................................... 1.75 hubcap tool........................................................................... 5.6 I indicators..............................................1.56, 1.75, 5.12 → 5.14 indicators: direction indicators............................................... 1.75, 5.15 exterior temperature indicator..................
Alphabetical index (4/5) P paintwork maintenance...................................................... 4.13 – 4.14 parking distance control.........................................2.35 → 2.37 power-assisted steering..................................................... 1.51 pretensioners...................................................................... 1.25 puncture..............................................................5.2, 5.6 → 5.8 R radio.........................................................
Alphabetical index (5/5) towing a caravan......................................................... 3.32, 6.9 towing equipment fitting............................................................................. 3.32 towing hitch............................................................. 5.31 – 5.32 towing rings.................................................... 1.35 – 1.36, 3.32 towing weights...................................................................... 6.9 traction control: ASR.................
( www.e-guide.renault.com ) RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
