MODUS DRIVER’S HANDBOOK
RENAULT recommends ELF ELF has developed a complete range of lubricants for RENAULT: f engine oils f manual and automatic gearbox oils Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please refer to your maintenance document. Benefiting from the research applied to Formula 1, lubricants are very high-tech products.
Welcome to your new vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections ............................... 1 ................................................................... 2 Your comfort . ........................................................ 3 Maintenance 4 Getting to know your vehicle Driving .......................................................... Practical advice ..................................................... . ..................................... 6 ................................................
0.
Section 1: Getting to know your vehicle Radio frequency remote control unit: general information, use, deadlocking. . . . . . . . . . . . . . . . . . Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic locking of opening elements when driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine immobiliser system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
key/RADIO FREQUENCY REMOTE CONTROL: general information (1/2) A B 5 C 3 3 2 2 1 1 5 4 4 Key A 1 Coded key for ignition switch, doors and fuel filler cap. Radio frequency remote control unit B or C 1 Locking the doors and tailgate. 2 Unlocking the doors and tailgate. 3 Driver’s door and ignition key. The key must not be used for any function other than those described in the handbook (removing the cap from a bottle, etc.). 1.2 4 Locking/unlocking the tailgate only.
key/RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the environment: take care not to lock or unlock the doors by inadvertently pressing the buttons on the remote control. Interference The presence of certain objects (metal objects, mobile telephones, or an area with strong electromagnetic radiation, etc.) close to the key may create interference and affect the operation of the system.
RADIO FREQUENCY REMOTE CONTROL: use (1/2) A B 2 2 1 1 Unlocking the doors Remote control A or B Press unlocking button 2. The hazard warning lights and indicator lights flash once to indicate that the doors have unlocked. Special notes (for some countries): – pressing button 2 enables the driver’s door only to be unlocked, – the other doors can be unlocked by pressing button 2 twice.
RADIO FREQUENCY REMOTE CONTROL: use (2/2) A B 2 2 1 1 3 Locking the doors Remote control A or B Press locking button 1. The indicator lights and hazard warning lights flash twice to indicate that the doors have locked: If a door or the tailgate is open or not properly shut, the doors or tailgate lock then quickly unlock and the hazard warning lights and indicator lights do not flash. 3 Unlocking/locking the tailgate only (for some countries) Press button 3 to unlock or lock the tailgate.
DEADLOCKING 1 1 Deadlocking of the doors/ tailgate To activate deadlocking This allows you to lock the doors and tailgate and to prevent the doors from being opened with the interior handles (by breaking the window and then trying to open the doors from the inside). The hazard warning lights and indicator lights flash five times to indicate that the doors have locked. (for some countries) Press button 1 twice in quick succession. Never use deadlocking if someone is still inside the vehicle. 1.
OPENING AND CLOSING THE DOORS (1/2) Lights-on warning buzzer If you have switched off the ignition and left the lights switched on, a warning buzzer will sound when a door is opened. 1 Opening the doors from the outside After the vehicle has been locked using the remote control or the key, pull handle 1.
OPENING AND CLOSING THE DOORS (2/2) Safety of rear occupants The driver can authorise operation of the rear doors and, depending on the vehicle, the electric windows by pressing switch 3 on the side with the illustration. 3 Child safety Vehicles fitted with switch 3 with integrated indicator light Press switch 3 to inhibit operation of the rear electric windows and opening of the rear doors from the inside. The indicator light in the switch confirms that the locks have been activated. 1.
LOCKING/UNLOCKING THE DOORS (1/2) Locking/Unlocking from the outside Refer to the information on the “Key, radio frequency remote control: general information”. 1 In some cases, the key/radio frequency remote control may not work: – if the vehicle is located in a zone of high electromagnetic radiation; – if the remote control battery is old or the vehicle battery discharged.
LOCKING/UNLOCKING THE DOORS (2/2) Locking/Unlocking doors from the outside (continued) Doors and tailgate status indicator light Using the door locking/unlocking interior control. The indicator light integrated in button 3 shows whether or not the doors and tailgate are locked: With the engine switched off and a front door open, press switch 3 for more than five seconds. Make sure you have your key with you before you leave your vehicle.
AUTOMATIC LOCKING WHEN DRIVING Operating faults You can decide whether you want to activate this function. To activate With the ignition on, press central door locking button 1 for approximately 5 seconds, until you hear one beep. To deactivate With the ignition on, press central door locking button 1 for approximately 5 seconds, until you hear one beep.
ENGINE IMMOBILISER This prevents the vehicle being driven by anyone not in possession of the vehicle’s coded ignition key. The vehicle is automatically protected a few seconds after the engine is switched off. 1 Operating principle When the engine is started, warning light 1 remains lit for a few seconds then goes out (refer to the information on “Starting the engine” in Section 2). Any unauthorised work carried out on the engine immobiliser (computers, wiring, etc.) could be dangerous.
FRONT HEADRESTS To remove the headrest Press button 2 and lift the headrest to release it. A To refit the headrest 1 2 Insert the headrest rods into the holes, with the notches facing forwards. Move tab 1 forwards and lower the headrest down to the required height. To raise the headrest Slide it upwards to the required height. To lower the headrest Move tab 1 forwards and lower the headrest down to the required height. For safety reasons, carry out any adjustments when the vehicle is not being driven.
REAR HEADRESTS B A 2 1 Positions for use To remove the headrest Press tab A of lock 1 and raise the headrest to its maximum height to use it in the high position. Lower it until it locks to use it in the bottom position. Press tab A on catches 1 and 2 then take out the headrest. Storage position Insert the rods into the holes, press the tabs on both rods and lower the headrest. Press catch 2 and lower the headrest completely.
FRONT SEATS 2 3 4 1 To move forwards or backwards Adjusting the height of the driver’s seat Lift handle 1 underneath the seat to release. Release the handle once the seat is in the correct position and ensure that the seat is fully locked into position. Move lever 2 as many times as necessary: To tilt the seatback Heated seats Turn control knob 4 and tilt the seatback to the desired position. – upwards to raise it; – downwards to lower it.
SEAT BELTS (1/4) Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in. Before starting, first adjust your driving position, then ask all passengers to adjust their seat belts to ensure optimum protection. Incorrectly adjusted or twisted seat belts may cause injuries in the event of an accident. Use one seat belt per person, whether child or adult. Even pregnant women should wear a seat belt.
SEAT BELTS (2/4) If your seat belt is completely jammed, pull slowly, but firmly so that just over 3 cm unwinds. Allow it to return slightly before attempting to unwind it again. If there is still a problem, contact an approved dealer. 1 ç 3 5 4 5 To fasten Unwind the belt slowly and smoothly and ensure that buckle 3 locks into catch 5 (check that it is locked by pulling on buckle 3). If the belt jams before it clicks in, allow it to return before attempting to unwind it again.
SEAT BELTS (3/4) 9 7 9 8 10 11 12 Rear side seat belts 7 Rear centre belt The belts are locked, unlocked and adjusted in the same way as the front belts. Unwind belt 9 slowly from its housing, then fasten buckle 8 into the corresponding black catch 11. Make sure that the rear bench seats are locked in position properly so that the seat belts will operate efficiently. Refer to the information on the “Rear bench seats” in Section 3. 1.18 Fasten sliding buckle 10 into the corresponding red catch 12.
SEAT BELTS (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) These are: – Have the entire restraint system checked following an accident. – pretensioners, – chest and lap belt force limiters, – No operation whatsoever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical. – air bags for driver and front passenger.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Chest-level and lap belt load limiters Air bags for driver and front passenger Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. Fitted to the driver and passenger side.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operation 1 This system is only operational when the ignition is switched on. In a severe frontal impact, the air bags inflate rapidly, cushioning the impact of the driver’s head and chest against the steering wheel and of the front passenger against the dashboard. The air bags then deflate immediately so that the passengers are not in any way hindered from leaving the vehicle.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
Methods of restraint in addition to the rear seat belts Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. – Have the entire restraint system checked following an accident. – No operation whatsoever is permitted on any part of the system (air bags, electronic control units, wiring) and the system components must not be reused on any other vehicle, even if identical.
SIDE PROTECTION DEVICES Side air bags This air bag may be fitted to each of the front seats and is activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Curtain air bags These air bags may be fitted along the top of each side of the vehicle and are triggered along the front and rear side windows to protect the passengers in the event of a severe side impact.
ADDITIONAL METHODS OF RESTRAINT All the warnings below are given so that air bag activation is not obstructed in any way and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times.
Child safety: General information (1/2) Carrying children Children - and adults - must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.
Child safety: General information (2/2) Never leave a child unattended in the vehicle. Check that your child is always strapped in and that the belt or safety harness used is correctly set and adjusted. Avoid wearing bulky clothing which could cause the belts to slacken. Never let your child put their head or arms out of the window. Check that the child is in the correct position for the entire journey, especially if asleep.
Child safety: Choosing a child seat Rear-facing child seats A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell. Forward-facing child seats The child’s head and abdomen need to be protected as a priority.
Child safety: Choosing a child seat mounting The are two ways of attaching child seats: via the seat belt or using the ISOFIX system. Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected. Always check that the seat belt is correctly fastened by pulling it up, then pulling it out fully whilst pressing on the child seat.
Child safety: Choosing a child seat mounting (continued) 5 1 4 3 2 The two rings 1 are located between the seatback and the seat base of the seat and are identified by a marking. To ensure your child seat can be easily fitted and locked on rings 1, use access guides 2 on the child seat. The 3rd ring is used to attach the upper belt on some child seats.
child safety: fitting a child seat (1/6) Some seats are not suitable for fitting child seats. The diagrams on the following pages show you how to attach a child seat. The types of child seats indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. Fit the child seat in a rear seat wherever possible. Check that when installing the child seat in the vehicle it is not at risk of coming loose from its base.
child safety: fitting a child seat (2/6) Child seat attached using the ISOFIX fitting ü ± = seat which allows an ISOFIX child seat to be fitted. = the rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. This is located on the roof rear cross member under a cover.
child safety: fitting a child seat (3/6) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
child safety: fitting a child seat (4/6) X =S eat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be attached by seat belt; check that it can be fitted. IUF/IL = On equipped vehicles, seat which allows a child seat with “universal/semi-universal or vehicle specific” approval to be fitted using the ISOFIX system; check that it can be fitted correctly. L = Seat which allows certain booster cushions to be fitted.
child safety: fitting a child seat (5/6) Child seat attached using the ISOFIX mounting ü ± = seat which allows an ISOFIX child seat to be fitted. = the rear seats are fitted with an anchorage point which allows a forward facing ISOFIX child seat with universal approval to be fitted. The anchoring ring is located on the roof rear cross member under a cover.
child safety: fitting a child seat (6/6) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
child safety: deactivating/activating the front passenger air bag (1/3) 1 2 Deactivating the front passenger air bags To deactivate the air bags: when the vehicle is stationary, push and turn lock 1 to the OFF position. You must deactivate the devices in addition to the front passenger seat belt before fitting a child seat in the front passenger seat.
child safety: deactivating/activating the front passenger air bag (2/3) A A 3 The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag. The child may suffer very serious injuries if the air bag is triggered. 1.
child safety: deactivating/activating the front passenger air bag (3/3) DANGER 1 2 Activating the front passenger air bags You should reactivate the air bag as soon as you remove the child seat from the front passenger seat to ensure the protection of the front passenger in the event of an impact. To reactivate the air bags: switch off the ignition, press and turn lock 1 to the ON position.
STEERING WHEEL 1 Steering wheel height adjustment Pull lever 1 and place the steering wheel in the required position; push the lever to lock the steering wheel in place. Make sure that the steering wheel is correctly locked. For safety reasons, only adjust the steering wheel when the vehicle is stationary. Never leave the steering wheel on full lock when the vehicle is stationary. Do not drive with a low battery charge. The steering wheel may not operate correctly.
DRIVER’S POSITION, LEFT-HAND DRIVE 12 26 1.
DRIVER’S POSITION, LEFT-HAND DRIVE (continued) The fittings described DEPEND ON THE VEHICLE VERSION AND COUNTRY. 1 Side window demister outlet. 9 Side air vent. 2 Side air vent. 10 Side window demister outlet. 3 Stalk for: – direction indicator lights; – exterior lights; – front fog lights; – rear fog lights. 11 Glove box. 12 Centre air vent. 13 Heating or air conditioning control. 20 Location for radio, navigation system, etc. 21 Hazard warning lights switch.
DRIVER’S POSITION, RIGHT-HAND DRIVE 1 2 26 3 25 24 23 4 22 21 20 1.
DRIVER’S POSITION, RIGHT-HAND DRIVE (continued) The fittings described DEPEND ON THE VEHICLE VERSION AND COUNTRY. 1 Side window demister outlet. 9 Side air vent. 2 Side air vent. 10 Side window demister outlet. 3 Location of passenger air bag. 11 Controls for: – parking distance control; – traction control; – electric headlight beam adjustment. 4 Centre air vents. 5 Instrument panel. 6 Stalk for: – direction indicator lights; – exterior lights; – front fog lights; – rear fog lights.
INSTRUMENT PANEL: warning lights (1/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. A The instrument panel A lights up when the ignition is switched on. In some cases, the appearance of a warning light is accompanied by a message. The © warning light means you should drive very carefully to an approved dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. 1.
INSTRUMENT PANEL: warning lights (2/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. À A This lights up when the ignition is switched on and goes out after a few seconds. If it comes on when you are driving accompanied by the ® warning light and a beep, it is essential to stop and switch off the ignition. Check the oil level. If the level is normal, the indicator light is being lit by something else. Contact an approved Dealer.
INSTRUMENT PANEL: warning lights (3/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. å A Air bag warning light This lights up when the ignition is switched on and goes out after a few seconds. If it does not light up when the ignition is switched on, or comes on when the engine is running, there is a fault in the system. Contact your approved Dealer as soon as possible. è x c Anti-lock braking warning light It comes on when the engine is started then goes out.
INSTRUMENT PANEL: warning lights (4/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. ç A Driver’s seat belt reminder warning light If the driver’s seat belt is not fastened it begins to flash when the vehicle reaches a speed of 12 mph (20 km/h) and a buzzer sounds for approximately two minutes.
INSTRUMENT PANEL: displays and indicators Rev counter 3 (scale x 1 000) 1 1a 2 3 4 5 6 6a The red zone indicates a prohibited engine speed Speedometer 4 (mph or km/h) Coolant temperature indicator 1 In normal use, the needle should be below the area marked 1a. Under severe conditions, the needle may enter this area. This is not serious unless the ® warning light comes on, accompanied by a message on the instrument panel and a beep. Gear engaged indicator 2 (for vehicles with an automatic gearbox). 1.
INSTRUMENT PANEL: displays and indicators (continued) 7 8 9 Instrument panel brightness adjustment button 7 Refer to the information on “Exterior lighting and signals” in Section 1. 9 Multifunction display 9 This displays several types of information: multimedia information, clock, external temperature. Clock setting button 8 Refer to the information on the “Clock” in Section 1. 1.
TRIP COMPUTER: general information (1/2) c) mileage before service, 2 1 d) programmed speed (speed limiter/ cruise control), e) on-board log: operating fault and information message readout. Instrument panel in miles It is possible to switch to km/h. 3 Trip computer and warning system 1 Display selection keys 2 and 3 Depending on the vehicle, this includes the following functions: Scroll through the following information in this order or reverse the order by briefly pressing the key repeatedly.
TRIP COMPUTER: general information (2/2) 2 Interpreting some of the values displayed after resetting The values showing average fuel consumption, range and average speed will become more stable and reliable the further you travel after pressing the reset button. For the first few miles after pressing the reset button you may notice: 3 Resetting the trip mileage With the “trip mileage recorder” selected on the display, press and hold button 2 or 3 until the mileage recorder is reset.
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (1/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected a) Total mileage recorder Trip mileage recorder FUEL USED 30.5L AVERAGE 5.3L/100 1.54 b) Journey parameters Fuel consumed since the last reset. Average fuel consumption since the last reset.
TRIP COMPUTER AND WARNING SYSTEM: trip parameters (2/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections CURRENT 12.3L/100 Interpreting the display selected Current fuel consumption This value is displayed after a speed of approximately 18 mph (30 km/h) is reached. Estimated range with remaining fuel This range takes into account the average fuel consumption since the last time the reset button was pressed.
TRIP COMPUTER AND WARNING SYSTEM: trip parameters (3/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
TRIP COMPUTER AND WARNING SYSTEM: trip parameters (4/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected CRUISE CONTROL 90KM/H d) Cruise control/speed limiter speed setting (depending on vehicle) Refer to the information on the “Cruise control - Speed limiter” in Section 2.
TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpreting the display selected “BOOT OPEN” Indicates that the tailgate has been left open. “OIL LEVEL OK” Indicates that the oil level is correct when the ignition is switched on. “AUTO LIGHTS ACTIVATED” 1.
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The © warning light stays on. Examples of operating fault messages are given in the following pages.
TRIP COMPUTER AND WARNING SYSTEM : warning messages These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
INFORMATION DISPLAYS B A B C C A D 2 1 Depending on the vehicle, displays 1 or 2 may show: – the external temperature (zone A); – the radio (zone B); – the time (zone C); – navigation aid information (zone D). If the electrical supply is cut (battery disconnected, broken supply wire, etc.), the clock will lose its time setting. The clock must be reset. We recommend that you do not adjust these settings while driving. 1.
CLOCK 2 1 The time is displayed when the ignition is switched on. 2 1 Resetting the clock 1 – press button 2 for approximately three seconds to enter time setting mode; – when the hour flashes, press button 2 again to adjust it; – wait approximately three seconds, the minutes will flash; press button 2 to set the minutes; – wait approximately three seconds, the minutes will stop flashing; the time is set. If the electrical supply is cut (battery disconnected, broken supply wire, etc.
EXTERNAL TEMPERATURE 1 1 External temperature indicator 1 The external temperature is displayed when the ignition is switched on. Special note: When the outside temperature is – 3 °C to + 3° C, the °C characters flash (signalling a risk of black ice on the road). External temperature indicator As ice formation is related to exposure, local air humidity and temperature, the external temperature alone is not sufficient to indicate the presence of ice. 1.
DOOR MIRRORS (1/2) A B 1 Door mirrors with manual adjustment To adjust the mirror, move lever 1. The driver’s door mirror may have two clearly defined zones. Zone B shows what can normally be seen in an ordinary rear view mirror. For your safety, zone A increases the area you can see at the rear and to the side of your vehicle. The objects in zone A look much further away than they really are. 1.
DOOR MIRRORS (2/2) Folding door mirrors A Move button 2 to position F and the door mirrors fold in. B D To reset them for driving, return to position C, D or E. Heated door mirrors C F E 2 With the engine running, mirror deicing is activated simultaneously with rear screen de-icing/demisting. Electric door mirrors With the ignition on, move button 2: – position C to adjust the left-hand door mirror; – position E to adjust the right-hand door mirror; D is the inactive position.
AUDIBLE AND VISUAL SIGNALS é 1 0 A 2 Horn Direction indicators Press steering wheel boss A. Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. Headlight flasher To flash the headlights, even if the lights are not on, pull stalk 1 towards you. When driving on the motorway, the steering wheel is not often turned enough to return the stalk automatically to 0. There is an intermediate position in which the stalk may be held when changing lanes.
EXTERIOR LIGHTING AND SIGNALS (1/5) 1 3 2 1 u 3 Adjusting the brightness of the instrument panel lighting Switching on the side lights Turn the end of stalk 1 until the symbol is opposite mark 2. In all cases, an indicator light on the instrument panel comes on. Before driving at night, check that the electrical equipment is operating correctly and adjust the headlight beams (if your vehicle is not carrying its normal load).
EXTERIOR LIGHTING AND SIGNALS (2/5) 1 2 – To activate it, with the ignition on, press button 4 for at least four seconds. An instrument panel message confirms this action. Switching on dipped beam headlights Manual operation Turn the end of stalk 1 until the symbol is opposite mark 2. In all cases, an indicator light on the instrument panel comes on. 1.
EXTERIOR LIGHTING AND SIGNALS (3/5) Cornering lights 1 Depending on the vehicle, if the dipped beam headlights are on when cornering, and under certain driving conditions (speed, steering wheel angle, forwards gear selected, etc.), additional lights are switched on to light the inside of the bend. Automatic lighting with main beam headlights Depending on the vehicle, when you change to main beam headlights, the dipped beam headlight raise to improve lighting.
EXTERIOR LIGHTING AND SIGNALS (4/5) 1 Switching off the lights Manual operation There are three options (depending on the vehicle): – return stalk 1 to its initial position; – the lights extinguish when the engine is stopped, when the driver’s door is opened or when the vehicle is locked. In this case, the next time the engine is started the lights will be switched back according to the position of the stalk 1; – a timer will switch off the lights automatically. 1.
EXTERIOR LIGHTING AND SIGNALS (5/5) 5 1 6 g f Rear fog light Switching off the lights Turn centre ring 5 on stalk 1 until the symbol faces mark 6, then release it. Turn ring 5 again until mark 6 is opposite the symbol for the fog light you wish to switch off. The fog light can only be switched on if the dipped beam headlights or front fog lights are lit. The front and rear fog lights switch off when the exterior lights are switched off.
ELECTRIC BEAM HEIGHT ADJUSTMENT Examples of positions for control A depending on the load Driver only 0 Driver with one front passenger 0 Driver with one front passenger and three rear passengers 1 Driver with one front passenger, three rear passengers and luggage 2 Driver with luggage or load reaching the maximum permissible all-up weight 3 A On vehicles fitted with this function, control A allows you to adjust the height of the beams according to the load.
WINDSCREEN WASH/WIPE (1/2) 1 2 1 A B C D With the ignition on, move stalk 1 A park B intermittent wiping The wipers will pause for several seconds between sweeps. It is possible to change the time between sweeps by turning ring 2. C normal wiping speed D fast wiping speed Special note When the vehicle is being driven, the wiping speed slows down whenever the vehicle stops. The speed will change from fast wiping speed to normal wiping speed.
WINDSCREEN WASH/WIPE (2/2) Headlights on The headlight washers will be activated at the same time. 1 A B C D Windscreen washers, headlight washers (depending on vehicle) With the ignition on, pull stalk 1 towards you. Headlights off A short press triggers one sweep cycle of the wiper. A longer press triggers three sweeps followed by a final sweep after several seconds. 1.74 In frosty weather, make sure that the wiper blades are not stuck by ice (risk of motor overheating).
REAR SCREEN WASH/WIPE p 1 2 Rear screen wash/wipe With the ignition on, turn the end of stalk 1 to align mark 2 with the symbol. When the stalk is released, it returns to the rear screen wiper position. Special note If the windscreen wipers are operating or are in automatic mode, the rear screen wiper wipes intermittently when reverse gear is engaged. Y timer Speed-dependent rear screen wiper with With the ignition on, turn the end of stalk 1 to align mark 2 with the symbol.
FUEL TANK (1/2) Fuel grade Use a high grade fuel that complies with the standards currently in force in each country. 1 2 A Diesel version A It is essential to use diesel fuel that conforms with the information given on the label inside cover A. Make sure that no water accidentally enters the fuel tank during filling. The shut-off system and its surrounding area must be dust-free. Capacity of the fuel tank: 49 litres approximately.
FUEL TANK (2/2) Petrol version It is essential to use unleaded petrol. The octane rating (RON) must conform with the specifications given on the label inside fuel filler flap A. Refer to the information on “Engine specifications” in Section 6. Special features of vehicles running on ethanol-based fuel: It is essential to use unleaded petrol or fuel containing a maximum of 85% ethanol (E85).
1.
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ignition switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starting/stopping the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RUNNING IN Petrol version Diesel version For the first 600 miles (1,000 km), do not exceed 78 mph (130 km/h) in the highest gear, or 3,000 to 3,500 rpm. For the first 900 miles (1,500 km), do not exceed 2,500 rpm. After completing this mileage you may drive faster, although you may only expect top performance after approximately 3,600 miles (6,000 km). You may only expect top performance from your vehicle after approximately 1,800 miles (3,000 km).
IGNITION SWITCH Ignition on position M The ignition is switched on. Start position D If the engine fails to start at the first attempt, the key must be turned back before the starter can be activated again. Release the key as soon as the engine starts. Note: on diesel versions, several seconds may pass between turning the key and the engine starting to allow for engine preheating. Position S: Off and steering lock applied To lock: remove the key and turn the steering wheel until the steering column locks.
STARTING/STOPPING THE ENGINE Starting the engine É Petrol injection Cold or warm engine Engine warm or cold – urn the key to the start position T without depressing the accelerator. – Release the key as soon as the engine starts. – Diesel injection Stopping the engine With the engine idling, turn the key back to the Stop position. urn the key to “Start” position D T without depressing the accelerator. – Release the key as soon as the engine starts.
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: – driving for long periods when the low fuel level warning light is lit; – using leaded petrol; – using fuel or lubrication additives which are not approved.
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Diesel engines are fitted with injection equipment which prevents the engine speed being exceeded irrespective of the gear selected. When driving, depending on the fuel grade used, it is possible that white smoke may be emitted. This is due to the exhaust particle filter being cleaned automatically, and does not affect the way the vehicle runs.
SPECIAL FEATURES OF DIESEL VERSIONS FITTED WITH A PARTICLE FILTER Ü Depending on the vehicle, the warning light comes on to indicate a filter saturation risk. Within 60 miles (100 km) of the message appearing, drive at an average speed of 24 mph (40 km/h), as traffic conditions and speed limits allow, until the warning light goes out. If the vehicle is stopped before the message disappears you will have to restart the process from the beginning.
GEAR LEVER/POWER-ASSISTED STEERING Power Assisted Steering Never drive with an inadequately charged battery. 1 Variable power assisted steering The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) whilst the force needed to steer increases progressively as the speed rises (for enhanced safety at high speeds).
HANDBRAKE To apply Pull upwards. Check that the vehicle is immobilised. 2 1 To release Pull lever 1 up slightly, press button 2 and then lower the lever to the floor. The red warning light on the instrument panel will stay on if you are driving with the handbrake not fully released. Make sure that the handbrake is properly released when driving (red indicator light off), otherwise overheating, or even damage, may occur.
ADVICE: antipollution, fuel economy and driving (1/3) By virtue of its design, moderate fuel consumption and initial settings, your vehicle conforms to current antipollution regulations. The manufacturer is actively striving to reduce pollutant exhaust gas emissions and to save energy. But the fuel consumption of your vehicle and the level of pollutant exhaust gas emissions are also your responsibility. Ensure that it is maintained and used correctly.
ADVICE: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring system – Sporty driving uses a lot of fuel: drive with a light right foot. – Brake as little as possible. If you anticipate an obstacle or bend in advance, you may then simply release the accelerator pedal. – Do not try to maintain the same speed up a hill, accelerate no more than you would on the level. Keep your foot in the same position on the accelerator pedal.
ADVICE: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air conditioning, it is normal to observe an increase in fuel consumption (especially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Environment Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. This commitment is illustrated by the Renault eco² signature. Emissions Manufacture Our vehicles are also equipped with a particle filter system including a catalytic converter, an oxygen sensor and an active carbon filter (the latter prevents vapour from the fuel tank being released into the open air).
ANTI-LOCK BRAKING SYSTEM: ABS Under heavy braking, the ABS prevents the wheels from locking, allowing the stopping distance to be managed and keeping control of the vehicle. Under these circumstances, the vehicle can be steered to avoid an obstacle whilst braking. In addition, this system can increase stopping distances, particularly on roads with low surface grip (wet ground, etc.). You will feel a pulsation through the brake pedal each time the system is activated.
ELECTRONIC STABILITY PROGRAM: ESP (1/2) This system helps to keep control of the vehicle in critical driving situations (avoiding an obstacle, loss of grip when cornering, etc.) and works in conjunction with the understeer control system. A When the ESP function starts operating, warning light A flashes to warn you. If the warning light comes on accompanied by the “traction control deselected” message when the engine is started, slowly turn the steering wheel from lock to lock to reinitialise the system.
ELECTRONIC STABILITY PROGRAM: ESP (2/2) Disabling the function A The function is deactivated by pressing switch 1; warning light A will come on to warn you that the system has been deactivated. This action also deactivates the traction control mechanism: the message “ASR deselected” appears on the instrument panel. Refer to the information on “Traction control: ASR" in the following pages. Correct this as soon as possible by pressing switch 1 again.
TRACTION CONTROL: ASR (1/2) This system helps to limit skidding on drive wheels and to control the vehicle when pulling away or accelerating. A The system also adjusts the engine speed to the grip available under the wheels, independently of the pressure exerted on the accelerator pedal. When the function begins to operate, warning light A flashes to warn you.
TRACTION CONTROL: ASR (2/2) Disabling the function A In some situations (driving on very wet ground: snow, mud, etc. or driving with snow chains fitted), the system may reduce the engine output to limit wheelspin. If this is not required, it is possible to deactivate the function by pressing switch 1. The “traction control deselected” message is displayed on the instrument panel along with warning light A to inform you. Disabling the function also disables the ESPfunction..
EMERGENCY BRAKE ASSIST This system is complementary to the ABS and helps reduce vehicle stopping distances. Operating principle The system is for detecting an emergency braking situation. In this case, the braking assistance immediately develops maximum power and may trigger ABS regulation. ABS braking is maintained as long as the brake pedal is applied. Hazard warning lights activation Depending on the vehicle, these may light up in the event of sudden deceleration.
CRUISE CONTROL/SPEED LIMITER: limiter function (1/3) 2 3 4 5 1 6 The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. This may be useful, for example, driving in urban areas or areas with a speed restriction (roadworks), etc. The system operates from a driving speed of about 18 mph (30 km/h). Controls 1 Main “On/Off” switch. 2 Limit speed activation, storage and increase switch (+).
CRUISE CONTROL/SPEED LIMITER: limiter function (2/3) Varying the limit speed You can vary the limit speed by pressing switch 2 repeatedly to increase the speed or switch 3 (-) to decrease it. 2 3 4 5 1 Switching on Press switch 1 on the side showing Ð . The indicator light on the instrument panel will come on. Limiting the speed At a steady speed (above 20 mph (30 km/h)), press switch 2 (+): the speed is stored.
CRUISE CONTROL/SPEED LIMITER: limiter function (3/3) Limit speed cannot be maintained In some driving conditions (for example when driving up or down a steep gradient), the system is unable to maintain the limit speed: the stored speed on the instrument panel information display will flash to inform you of this situation. 2 3 4 5 Putting the function on standby 1 1 The speed limiter function is interrupted when you: – press switch 4 (O); – engage reverse gear.
CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4) 2 1 The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 18 mph (30 km/h). 3 4 5 This function is an additional driving aid. However, the function does not take the place of the driver.
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4) Driving Once a cruising speed is stored and the cruise control function is active, you may lift your foot off the accelerator pedal. 2 3 4 5 1 Switching on Activating cruise control Press switch 1 on the side showing At a steady speed (above 20 mph (30 km/h)), press switch 2 (+) or 3 (-): the function is activated and the speed is stored. Ï .
CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed In the event of an emergency 2 3 4 5 The cruising speed may be exceeded at any time by depressing the accelerator pedal. Whilst the speed is being exceeded, the cruising speed displayed on the instrument panel flashes. Then, release the accelerator: the vehicle will automatically return to its set cruising speed.
CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4) Recalling the cruising speed 2 3 4 5 If a speed has been stored, it is possible to recall it by pressing switch 5 (R) (the “Cruise control” message appears on the instrument panel) on condition that you are driving faster than 18 mph (30 km/h) and that you are sure that the driving conditions are suitable (traffic, road surface condition, weather conditions, etc.).
26590 AUTOMATIC GEARBOX (1/4) 1 A 3 2 4 Selector lever 1 Operation Display A on the instrument panel shows the mode and gear selected. With gear lever 1 in position P or N, switch on the ignition. P: park To move out of position P, you must depress the brake pedal whilst simultaneously pressing unlocking button 2. R: reverse N: neutral D: automatic mode (in forwards gear only) 3: displays gear engaged in manual mode.
AUTOMATIC GEARBOX (2/4) Accelerating and overtaking Driving in manual mode Depress the accelerator pedal firmly and fully (so that it goes beyond the kickdown point). This will enable you to change down to the optimum gear within the engine range. With selector lever 1 in position D, pull the lever to the left (changing gear using the lever).
AUTOMATIC GEARBOX (3/4) – Vehicles not fitted with traction control: on a slippery surface or surface with a low level of adhesion, select second gear manually before starting the engine to avoid wheelspin when starting. 4 5 Parking the vehicle When the vehicle is stopped, move the lever to position P while keeping your foot on the brake pedal: the gearbox is in neutral and the drive wheels are mechanically locked by the driveshaft. Apply the handbrake.
AUTOMATIC GEARBOX (4/4) Operating faults – When driving, if the message “Check gearbox” and the © warning light appear on the instrument panel, this indicates a fault. 2 Contact your approved Dealer as soon as possible. – When driving, if the message “Gearbox overheating” appears on the instrument panel, drive at a moderate speed and avoid leaving the lever in the D (or R) position, where traffic conditions allow: always return to the N position when you stop.
QUICKSHIFT GEARBOX (1/5) 2 1 5 4 3 Selector lever 1 Display A/M to change mode (automatic/ manual) 2 automatic mode ▲ to change up a gear 4 brake pedal depressed indicator light ▼ to change down N neutral 3 gear display 5 snow mode R reverse For safety reasons, do not switch off the ignition before the vehicle has come to a complete standstill. The oil level in the automatic gearbox system reservoir varies depending on use.
QUICKSHIFT GEARBOX (2/5) Starting The display shows N (neutral) and A (automatic mode). Moving off forwards – With your foot on the brake pedal, push the selector lever forwards or backwards and then release it again. 4 – Release the brake pedal then accelerate gently to move forwards. Reverse Operation Switch on the ignition. The display on the instrument panel switches on. By default: – automatic mode is selected (letter A on the display), – and neutral is engaged (letter N on the display).
QUICKSHIFT GEARBOX (3/5) Changing mode Driving in manual mode You can change mode at any time by pushing the lever to the left. This switches mode without changing gear. Using the selector lever Pushing the lever repeatedly allows you to change gears manually.
QUICKSHIFT GEARBOX (4/5) Accelerating and overtaking To obtain maximum vehicle performance, in automatic or manual mode selected, quickly depress the accelerator pedal beyond the kickdown point. A This will activate the kickdown function allowing you to change down to the most suitable gear. 5 Parking To park the vehicle with a gear engaged (on a slope, for example): before switching off the engine, check that a gear other than N is displayed on the instrument panel.
QUICKSHIFT GEARBOX (5/5) Operating faults “Check gearbox” If, when driving, the message “check gearbox” and the © warning light appear on the instrument panel, this indicates a fault. Contact an approved dealer as soon as possible. “Gearbox overheating” If you keep the vehicle on a slope for too long without applying the brakes or handbrake, the message “gearbox overheating” will appear along with the © warning light. Depress the brake pedal or apply the handbrake.
PARKING DISTANCE CONTROL Operating principle Ultrasonic sensors, fitted in the vehicle’s rear bumper, measure the distance between the vehicle and an obstacle when reversing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 30 centimetres from the obstacle. There is a beep when changing to reverse gear.
PARKING DISTANCE CONTROL (continued) Operating faults When the system detects an operating fault there will be a 5-second, continuous warning beep when reverse gear is selected. Consult an approved Dealer. 1 Prolonged deactivation of the system You can deactivate the system permanently by pressing switch 1 and holding it down for approximately three seconds. The indicator light built into the switch remains lit constantly.
2.
Section 3: Your comfort Air vents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heating and air conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electric windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electric sunroof. . . . . . . . . . . . . . . . .
AIR VENTS (air outlets) 1 2 3 4 5 6 7 8 1 left-hand side window demister outlet 2 left-hand side air vent 5 control panel 6 right-hand side air vent 3 windscreen demisting vents 7 right-hand side window demister outlet 4 centre air vents 8 passenger footwell heater outlets 3.
AIR VENTS (continued) To remove bad odours from your vehicles, only use the systems designed for this purpose. Consult an approved Dealer. 1 3 2 2 4 Air flow Direction Move the control knob 1 or 3 (beyond the resistance point). Right/left: move tabs 2 or 4. o: maximum air flow. z: closed. Up/down: lower or raise tabs 2 or 4. Do not add anything to the vehicle’s ventilation circuit (for example, to remove bad odours). There is a risk of damage or of fire. 3.
HEATING/AIR CONDITIONING (1/4) A B F The controls A Passenger compartment air distribution adjustment. B Air temperature adjustment. C Ventilation speed adjustment. D Air recirculation control. 3.4 C D E E Heated rear screen and heated door mirror control and indicator light (depending on vehicle). F Air conditioning operation control and indicator light (depending on vehicle). Information and advice on use: refer to the end of the information on “Air conditioning”.
HEATING/AIR CONDITIONING (2/4) F G A well. The air flow is directed mainly towards the passenger foot- The air flow is directed mainly towards all the air vents and the passenger footwells. This is the recommended position for the best temperature in hot weather. ô Distribution of air in the passenger compartment Move control A to position the pointer opposite the marked positions. W All the air flow is directed to the demisting vents for the windscreen and the side windows.
HEATING/AIR CONDITIONING (3/4) Adjusting the air temperature B Turn control B to obtain the desired temperature. The further the slide is in the red, the more the temperature will be increased. C Switching air conditioning on or off The air conditioning is switched on (indicator light illuminated) or off (indicator light extinguished) using button F. The air conditioning system is used for: – lowering the temperature inside the passenger compartment; – eliminating condensation.
HEATING/AIR CONDITIONING (4/4) D Rear screen de-icing/ demisting With the engine running, press button E. The operating tell-tale comes on. This function permits rapid demisting/ de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles). To exit this function, press button E again. Demisting automatically stops.
AUTOMATIC CLIMATE CONTROL 1 2 3 4 5 6 7 12 Heated rear screen and heated door mirrors (depending on vehicle). 8 13 Heated rear screen warning light. 14 Air recirculation control. Information and advice for use 14 9 13 12 The controls 1 Clear View button to demist and de-ice the windows. 2 Clear View function indicator light. 3 Switching the air conditioning on and off. Refer to the end of the information on “Heating/air conditioning”. 11 10 5 Display. 6 Starting automatic mode.
AUTOMATIC CLIMATE CONTROL (continued) 4 6 7 – press button 7 to increase the temperature; – press button 4 to decrease the temperature. Note: The maximum and minimum settings of 15°C and 27°C allow the system to produce a minimum or maximum temperature, whatever the ambient conditions. Ambient temperature :automatic mode Press button 6. Only the temperature and the AUTO symbol are displayed. Functions managed in automatic mode are not displayed.
AUTOMATIC CLIMATE CONTROL (continued) Adjusting automatic mode Ambient temperature: automatic mode (continued) The automatic mode is the system’s normal operating mode (AUTO light on) but you may alter the selections made by the system (air distribution, etc.). Operation To reach and keep the chosen comfort level and to maintain good visibility, the system controls: – ventilation speed; – air distribution; – air recirculation management; – air conditioning start/stop; – air temperature.
AUTOMATIC CLIMATE CONTROL (continued) 5 6 8 G F The air flow is directed towards all the air vents and the passenger footwells. well. Distribution of air in the passenger compartment There are five possible combinations for air distribution, which may be selected by pressing buttons 8 and 10 repeatedly.
AUTOMATIC CLIMATE CONTROL (continued) Varying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. 3 5 6 Automatic mode is switched off by pressing buttons 9 and 11. These buttons allow you to increase or decrease ventilation speed. If you set the ventilation speed to zero, the system switches off.
AUTOMATIC CLIMATE CONTROL (continued) 13 12 Rear screen de-icing/ demisting With the engine running, press button 12. The operating tell-tale 13 comes on. To exit this function, press button 12 again. Demisting automatically stops by default. This function permits rapid demisting/ de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles). 3.
AUTOMATIC CLIMATE CONTROL (continued) 1 2 Note: if you wish to reduce the air flow (which may produce a certain amount of noise in the passenger compartment), press button 11. 6 To exit this function, press either: – button 1 again, – button 6 (the AUTO indicator light on the display will light up). 13 12 Clear View function With the engine running, press button 1, and operating tell-tale 2 comes on. The AUTO button indicator light (on the display) goes out.
AUTOMATIC CLIMATE CONTROL (continued) 14 Air recirculation mode Pressing button 14 activates air recirculation (the symbol lights up on the display). During recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle. Air recirculation allows the external atmosphere to be cut off (when driving in polluted areas, etc.).
AIR CONDITIONING: information and advice on use Operating faults Fuel consumption You will normally notice an increase in fuel consumption (especially when driving in town) when the air conditioning is operating. For vehicles fitted with manual air conditioning, switch off the system when it is not required. Advice for reducing consumption and therefore helping to preserve the environment: Drive with the air vents open and the windows closed.
ELECTRIC WINDOWS 5 1 4 6 3 7 2 With the ignition on Press the switch for the relevant window to lower it to the desired height (the rear windows cannot be lowered completely). Raise the switch for the relevant window to raise it to the desired height. Driver’s seat Operate the switches as follows: – 1 for the driver’s side; – 2 for the front passenger’s side; – 3 and 5 for the rear passenger windows. Front passenger seat Press switch 6. Rear seats Press switch 7.
ONE-TOUCH ELECTRIC WINDOWS (1/2) 1 4 Driver’s responsibility The one-touch mode works in addition to the operation of the electric windows described previously. It is fitted to the driver’s window if it is present on the vehicle. Press switch 1. The system operates: – with the ignition on; – with the ignition off until the driver’s door is opened/closed (approximately 20 minutes limit).
ONE-TOUCH ELECTRIC WINDOWS (2/2) MANUAL WINDOW WINDERS One-touch mode Normal mode – Fully and briefly press down on the relevant switch down: the window will open completely. – Press down on the relevant switch to lower the window and release it when the window is at the desired height. – Fully and briefly lift the relevant switch: the window will close completely. Pressing the switch again while the window is moving will stop its movement.
ELECTRIC SUNROOF A 0 B Never operate the sunroof with the blind closed. C D 1 Never drive the vehicle with the sunroof open and the sun blind closed. 1 2 The system operates: – with the ignition on, – with the ignition off until the driver’s door is opened/closed for the first time (approximately 20 minutes limit).
ELECTRIC SUNROOF (continued) Sunroof closing operating fault 0 In this case, check that nothing is obstructing it. Turn button 2 to position 0, then press button 3 until the sunroof is completely closed. Precautions during use – check that the sunroof is properly closed before leaving your vehicle; – clean the seal every three months using products recommended by our Technical Department; – do not open the sunroof immediately after the vehicle has been in the rain or after your car has been washed.
SUN VISOR 1 3 4 5 A 6 7 B 2 Front sun visor Lower one of the sun visors 1. Courtesy mirrors Slide cover 2. 3.22 Child minder mirror 3 Side sun blinds A and B Pull tab 5 forwards and tab 6 towards the rear of the vehicle until they both click into their respective housings 4 and 7.
INTERIOR LIGHTING Map reading lights (depending on vehicle) 1 Press switch 1 for the driver, 3 for the front passenger. 2 3 4 Courtesy light Press switch 2. This provides: – permanent lighting; – intermittent lighting, which comes on when a door is opened.
PASSENGER COMPARTMENT STORAGE/FITTINGS (1/5) 3 2 1 Front door storage pockets 1 Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passengers during sudden turning, braking or in the event of an accident. 3.24 Driver’s and passenger footwell storage compartments 2 Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use.
PASSENGER COMPARTMENT STORAGE/FITTINGS (2/5) 4 5 6 Dashboard storage compartment 4 Depending on the vehicle, it may be fitted with a cover. Clip 5 This can be used for storing motorway tickets, cards, etc. Centre console storage compartment 6 This can be used for storing a mobile ashtray, cup holder, etc. When turning corners, accelerating or braking, ensure that the receptacle being held by the cup holder is not dislodged. There is a risk of injury if hot liquid escapes. 3.
PASSENGER COMPARTMENT STORAGE/FITTINGS (3/5) 9 10 7 9 8 Passenger seat with integrated object holder 7 To access this location, pull the tab at the rear of the seat base to tilt it forwards. This location can be used to store a handbag or documents, etc. There is a strap for holding documents. For safety reasons, before folding the seat base, check that there is nothing present in the object holder. 3.
PASSENGER COMPARTMENT STORAGE/FITTINGS (4/5) 13 14 11 12 Glove box 11 Pull handle 12 to open it. Depending on the vehicle, this glove box compartment is ventilated and air conditioned in the same way as the passenger compartment. Front seat storage compartments 14 Turn blanking cover 13 to open or close the air inlet. Audio Connection Box Depending on the vehicle, this socket is located in the passenger glove box. 3.
PASSENGER COMPARTMENT STORAGE/FITTINGS (5/5) 15 Rear parcel shelves 15 16 16 Roof compartments 16 Raise them to their horizontal position. It is recommended that you use the shelves only when the vehicle is stationary. – Always leave the storage compartment covers closed when driving: – there is a risk of injury when braking suddenly or in the event of an accident; – there is a risk of objects being hurled through the passenger compartment. Maximum weight in each compartment: 500 g evenly distributed.
ASHTRAYS - CIGAR LIGHTER Cigar lighter 2 With the ignition on, push in cigar lighter 2. It will spring back with a click when it is ready. Pull it out to use. After use, replace it without pushing it all the way in. 1 2 Ashtray 1 This is a removable ashtray which fits into the cup holder in the vehicle. If your vehicle is not fitted with a cigar lighter and an ashtray, these can be obtained from an approved Dealer. Connect accessories with a maximum power of 120 Watts only. Fire hazard. 3.
FIXED REAR BENCH SEAT (1/2) C A The seat and the seatback may be folded away to allow bulky objects to be carried. Start by folding down the seat base, then the seatback. 1 B 2 To fold away the seat base To fold down the seatback Lift up the front of the seat cushion A until it reaches the stop. Depending on the vehicle, it can be folded down in one or two sections. Ensure that both sides of the seat base are unlocked. Remove the rear headrests if necessary.
FIXED REAR BENCH SEAT (2/2) To raise the seatback Proceed in reverse order. Refit the seatback and click it back into place. 1 1 A 3 To raise the seat base Proceed in reverse order. Lower the bench seat cushion A in such a way as to position the rear section of the seat base 1 under the seatback. Allow the bench seat to turn on its axis naturally without forcing it, guiding it as it lowers onto the floor. Then push the front 3 of the cushion A in order to lock the seat base.
SLIDING REAR BENCH SEAT (1/3) 2 1 To move forwards or backwards To unlock the seat: – from the front, lift one of the levers 1; – from the rear, hold the bars of handle 2 and push them together. Move the seat forwards or back to the required position. Release lever 1 or handle 2 and make sure that the seat is locked correctly in position. For safety reasons, carry out any adjustments when the vehicle is not being driven. 3.
SLIDING REAR BENCH SEAT (2/3) 3 4 C B B C C B 5 The seat may be folded down to enable bulky objects to be transported. To fold down the seatbacks Special features of the triptic rear bench seat This must be in the three-seater configuration (refer to the information on “Triptic rear bench seat” in Section 3). Check that the rear seat belts are positioned and operating correctly each time the rear seat is moved.
SLIDING REAR BENCH SEAT (3/3) 2 6 8 7 To fold down the bench seat Triptic rear bench seat This should be in the 3-seater position (refer to the next page). Any sliding rear bench seat Bench seat pushed fully forward with the headrests in the low position: – fold down the seatbacks; – lift controls 7 located on each side of the bench seat; – lift the seat base with handle 2; – take out the strap from storage compartment 6; – attach it to one of the front headrest rods and pull it taut. 3.
triptic rear bench seat 1 1 1 A 2 2 This is a sliding bench seat which, in addition to the settings described in the previous pages, can be configured to two or three seats. Before moving it, ensure that nobody is occupying the seat or preventing it from being moved. For safety reasons, carry out any adjustments when the vehicle is not being driven. For safety reasons, it is not permitted to sit on the centre seat position when section 1 is raised.
TAILGATE 2 1 3 To open To close Operating faults Press button 1 and lift the tailgate. Lower the tailgate, initially using interior handles 2 to assist you. If it is not possible to unlock the tailgate, it can be unlocked manually from inside. – access the luggage compartment by folding forward the seatback(s) of the rear bench seat, – insert a pencil or similar object in cavity 3 and slide the unit as shown in the illustration, – push the tailgate to open it. 3.
Tailgate rear parcel shelf A A 1 C B 2 Parcel shelf A Vehicle with flexible cover B Vehicle with fixed cover C To remove: – unhook both straps 2; – remove the straps 2 from the guide 1; – unclip parcel shelf A. This is fixed in place with a velcro-type strip. To remove it, detach it from the rear bench seatback. Lift the parcel shelf. To refit: – Clip on the parcel shelf; – ensure that the straps feed correctly into the guides 1; – hook both straps. To refit it, proceed in reverse order to removal.
LUGGAGE COMPARTMENT FITTINGS 3 1 1 Location for anchorage points On equipped vehicles, these are for securing items transported in the luggage compartment (refer to the information on “Transporting objects in the luggage compartment”). Depending on the vehicle, a net for retaining luggage on the floor, located in the storage compartment under the passenger seat, may be attached to these hooks. 3.38 2 Strap Depending on the vehicle, this strap is used to hold a bottle, etc.
TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT If you have to place objects on the folded seatback, with the bench seat in the 3-seater position, remove the front headrests before folding the seatback so that is can be folded as flat as possible against the seat base. Always position the objects transported so that the largest surface is against: – The rear bench seatback for normal loads (example A). – The folded down seat for maximum loads (example B).
ROOF BARS When fitting roof bars, replace the blanking bolts with the mounting bolts supplied with the roof bars. 1 2 Access to the mounting points Open the doors. Behind seal 2 are blanking bolts 1 which protect the mounting bolt locations. Never remove blanking bolts 1 without plugging the holes afterwards. 3.40 For information on the range of equipment adapted to your vehicle, we advise you to consult an approved Dealer.
“VELOFIX” BIKE RACK Accessing the mounting points Unclip the blanking cover on each side of the rear bumper. For vehicles not fitted with blanking covers 1, contact your approved Dealer. 1 2 1 On vehicles equipped this accessory, the rear bumper is fitted with two flaps covering the mounting points for the bike rack and an electrical socket 2 located underneath the vehicle. Each flap is protected by a blanking cover 1. Bike rack permissible load: 30 kg.
3.
Section 4: Maintenance Bonnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . general information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . topping up, filling . . . . . . . . . . . . . . . . . .
BONNET (1/2) 3 5 1 To open the bonnet, pull the handle 1. Before opening the bonnet, remember to return the windscreen wiper stalk to park position (refer to the information on the “Windscreen wash/ wipe” in Section 1). 4.2 4 2 Unlocking the bonnet catch Opening the bonnet To open, push tab 2 to the left as you open the bonnet. Lift the bonnet and release stay 4 from its holder 5. For your own safety, it is very important to fix the stay into retainer 3 in the bonnet.
BONNET (2/2) 5 4 Closing the bonnet Before closing the bonnet, make sure that nothing has been left in the engine compartment. To close the bonnet, replace stay 4 in holder 5. Hold the middle of the bonnet and guide it down to one foot (30 cm) above the closed position, then release. It will latch automatically under its own weight. After carrying out any work in the engine compartment, check that nothing has been left behind (cloth, tools, etc.). These may damage the engine or cause a fire.
ENGINE OIL LEVEL: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level between oil changes. However, contact an approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period. Check the oil level at regular intervals and before any long journey to avoid the risk of damaging your engine.
ENGINE OIL LEVEL: general information (continued) Once the level has been checked, ensure that the dipstick is pushed in as far as it will go or that the cap-type dipstick is completely screwed in. B A Consult your approved Dealer at once if you notice an abnormal or repeated drop in any of the fluid levels. C B In order to prevent splashback, it is recommended that a funnel be used when topping up/filling with oil.
ENGINE OIL LEVEL: topping up, filling (1/2) 1 1 1 2 Topping up/filling – top up the level (as a guide, the capacity between the minimum and maximum reading on the dipstick 2 is between 1.5 and 2 litres, depending on the engine); Engine oil grade – wait for approximately 10 minutes to allow the oil to flow into the engine; Do not exceed the max level and do not forget to refit cap 1 and dipstick 2. 4.
ENGINE OIL LEVEL: topping up, filling (2/2) /OIL CHANGE Oil change Service interval: refer to the Maintenance Service Booklet for your vehicle. Average capacities for oil changes oil filter included (for information) 1.2 16V engine: 4.0 litres 1.2 16V TCE engine: 4.0 litres 1.4 16V engine: 4.8 litres 1.6 16V engine: 4.8 litres 1.5 dCi engine: 4.5 litres Engine oil grade Refer to the Maintenance Service Booklet for your vehicle.
LEVELS (1/3) 1 Checking intervals Replacement intervals Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). Refer to the Maintenance Service Booklet for your vehicle. If the level needs to be topped up, only use products approved by our Technical Department which ensure: – protection against freezing; – anticorrosion protection of the cooling system.
LEVELS (2/3) 2 Level 2 Filling It is normal for the level to drop as the linings become worn, but it should never drop below the MIN warning line. After any operation on the hydraulic circuit, a specialist must replace the fluid. Because of the reduced accessibility, we advise you to have the brake fluid level checked and if necessary topped up by a specialist.
LEVELS (3/3) FILTERS Filters 3 3 4 The replacement of filter elements (air filter, passenger compartment filter, diesel filter, etc.) is scheduled in the maintenance operations for your vehicle. Replacement intervals for filter elements: refer to the Maintenance Service Booklet for your vehicle. Windscreen/headlight washer reservoir Filling With the engine switched off, open cap 3, fill until you can see the fluid, then refit the cap.
BATTERY Replacing the battery As this operation is complex, we advise you to contact an approved Dealer. A 2 3 4 7 6 5 1 Label A Observe the indications on the battery: – 2n aked flames and smoking forbidden; – 3 eye protection required; – 4 keep away from children; – 5 explosive materials; – 6 refer to the handbook; – 7 corrosive materials. The battery 1 does not require any maintenance.
Bodywork maintenance (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the exterior of the vehicle regularly. Your vehicle has been treated with very effective anti-corrosion products. It is nevertheless subject to various outside influences. Corrosive agents in the atmosphere – atmospheric pollution (built-up and industrial areas), – saline atmospheres (near the sea, particularly in hot weather), – seasonal and damp weather conditions (e.g.
Bodywork maintenance (2/2) Respect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway). Observe the vehicle stopping distances when driving on gravelled surfaces to prevent paint damage. Repair, or have repaired quickly, areas where the paint has been damaged, to prevent corrosion spreading. Remember to visit the body shop periodically in order to maintain your anti-corrosion warranty. Refer to the Maintenance Service Booklet.
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the interior of the vehicle regularly. A stain should always be dealt with swiftly. Whatever type of stain is on the trim, use cold (or warm) soapy water with natural soap. Detergents (washing-up liquid, powdered products, alcohol-based products) should not be used. Use a soft cloth. Rinse and soak up the excess. Glass instrument panel (e.g.
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable equipment originally fitted in the vehicle If you need to remove equipment in order to clean the passenger compartment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driver’s mat should be fitted on the driver’s side, etc.) and fit them with the components supplied with the equipment (for example, the driver mat should always be fixed using the pre-fitted mounting components).
Tyre pressure Note: the number of lines on the label may vary depending on the vehicle. A A B B The tyre pressure is indicated on label A affixed to the edge of the driver’s door. Open the door to read it. C D E F C E D F F: tyre pressures for the rear wheels (motorway). B: dimension of the tyres fitted to the vehicle. C: tyre pressures for the front wheels (non-motorway). D: tyre pressures for the rear wheels (non-motorway). E: tyre pressures for the front wheels (motorway). 4.
Section 5: Practical advice Puncture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tool kit (jack, wheelbrace, etc.). . . . . .
Puncture, emergency spare wheel (1/4) In the event of a puncture, depending on the vehicle, you will have: An emergency spare wheel or tyre inflation kit (refer to the information on the following pages). If the emergency spare wheel has been stored for several years, have it checked by your Dealer to ensure that it is safe to use. Vehicles fitted with an emergency spare wheel smaller than the four other wheels: – Never fit more than one emergency spare wheel to the same vehicle.
Puncture, emergency spare wheel (2/4) 1 2 3 A 4 5 6 B 7 3 The emergency spare wheel is located underneath the vehicle. – Open the tailgate; – lift carpet 1 and place it against the back of the rear bench seat; 8 – unscrew nut 4 in an anti-clockwise direction until it comes off completely, then place the palm of your hand on section B of handle 5 and push towards the front of the vehicle. The wheel will be lowered.
Puncture, emergency spare wheel (3/4) 5 6 7 8 9 10 To refit a wheel To carry out this operation, the cable must be unwound. If the cable has been wound back up on its own, unwind it again as follows: – Pull the handle to unwind the cable, – press the button located under handle 5 to hold the unwound cable, then guide it down; – recover the cable from underneath the vehicle; – attach the cable end piece to the wheel support. You may refit the wheel. 5.
Puncture, emergency spare wheel (4/4) Note: if the tool kit does not lock in place, check the tightness of nut 4 and the correct positioning of handle 5. 1 5 4 Special features The emergency spare wheel holder should always be present when you are driving even when the wheel itself is not present: risk of water entering the vehicle. If you have to release it when it is not holding a wheel, push the centre of the wheel holder towards the ground while pressing handle 4.
TYRE INFLATION KIT (1/3) B A Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE INFLATION KIT (2/3) 1 With the engine running and the parking brake applied, – connect the adapter 8 to the accessories socket on the dashboard of the vehicle; 2 3 4 – unscrew the valve cap on the wheel concerned and screw the inflation adapter 6 onto the valve; – press switch 3 to inflate the tyre to the recommended pressure (check the label affixed to the edge of the driver’s door); 5 8 If a minimum pressure of 1.
TYRE INFLATION KIT (3/3) 3 5 7 8 6 Once the tyre is inflated correctly: – stop using the kit; – close the integrated cap on the bottle again; – disconnect adapter 8; – affix the driving recommendation label to the dashboard where it can easily be seen by the driver; Nothing should be placed around the driver’s feet as such objects may slide under the pedals during sudden braking manoeuvres and obstruct their use. 5.
TOOL KIT Hubcap tool 5 or 6 This tool is used to remove the wheel trims. 3 1 2 Jack 7 When replacing the jack, fold it up completely and replace it in its position. 7 A 4 6 Tool kit A is located in the luggage compartment. Storage compartment 1 To access the tools, lift the luggage compartment carpet, lift the cover and remove it. Storage compartment 2 Take out the tool kit, lifting it at both ends. To return it, proceed in the reverse order to removal.
WHEEL TRIMS - WHEEL 1 D B 3 4 C A 6 5 2 Wheel trim (example: wheel trim 1) Central wheel trim (example: wheel trim 4) Remove the wheel trim using hubcap tool 2 (located in the tool kit) by engaging the hook in the opening near valve 3. Remove the wheel trim using the hubcap tool 6 (located in the tool kit) inserting the tool 6 into the recess 5. To refit it, align it with valve 3.
CHANGING A WHEEL (1/2) 1 2 3 4 Switch on the hazard warning lights. Keep the vehicle away from traffic and on a level surface where it will not slip (if necessary, place a solid support under the jack base). Apply the handbrake and engage a gear (first or reverse, or P for automatic transmissions). Ask all the passengers to leave the vehicle and keep them away from traffic.
CHANGING A WHEEL (2/2) – undo the bolts and take off the wheel; – fit the emergency spare wheel on the central hub and turn it to align the mounting holes in the wheel and the hub; – tighten the bolts and lower the jack; – with the wheel on the ground, tighten the screws as fully as possible and check the tightness as soon as possible (tightening torque 105 N.m). Anti-theft bolt If you use anti-theft bolts, fit these nearest the valve (otherwise it may not be possible to fit the wheel trim).
TYRES (1/3) Tyre and wheel safety The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. 1 You must make sure that your tyres conform to local road traffic regulations. 2 When the tyre tread has been worn to the level of the wear indicators, they become visible 2: it is then necessary to replace your tyres because the tread rubber is no more than 1.6 mm deep, resulting in poor roadholding on wet roads.
TYRES (2/3) Tyre pressures Tyre pressures must be adhered to (remember to check the emergency spare wheel at the same time). Inflation pressures must be checked at least once a month and always before a long journey (refer to the information on “Tyre pressures”.) Incorrect tyre pressures lead to abnormal tyre wear and unusually hot running.
TYRES (3/3) Use in winter – Chains For safety reasons, fitting snow chains to the rear axle is strictly forbidden. Chains cannot be fitted to tyres which are larger than those originally fitted to the vehicle. – Snow or winter tyres We would recommend that these be fitted to all four wheels to ensure that your vehicle retains maximum adhesion.
HALOGEN HEADLIGHTS: changing bulbs Direction indicator lights A 1 B Turn cover B a quarter of a turn to access the bulb. Bulb type: PY21W. Replace the bulb. D When the bulb has been changed, make sure you refit the cover correctly. C Due to their reduced accessibility, (sometimes requiring the removal of bodywork or mechanical components) we advise you to have your bulbs replaced by an approved Dealer. Front side light Remove cover A, then unclip bulb holder 1 to access the bulb. Bulb type: W5W.
HALOGEN HEADLIGHTS: changing bulbs (continued) 2 3 D C Dipped beam/main beam headlights Remove cover C or D. Remove connector 4 or 6 from the bulb concerned. 7 6 4 5 Refit connector 4 or 6. Do not touch the bulb glass. Hold it by its base. Refit clip 3 or 7, then cover C or D. Unclip clip 3 or 7. Replace the bulb. Bulb type: only use anti UV 55W bulbs to ensure the plastic glass on the headlights is not damaged.
HEADLIGHTS: additional/front fog lights Additional lights If you wish to fit fog lights or long range headlights to your vehicle, consult an approved Dealer. 2 1 Front fog lights 1 Vehicles with cornering lights 2 Because it is sometimes necessary to remove the protectors (bumper), you are advised to have your bulbs replaced by an Approved dealer. Bulb type: H11. The engine may be hot when carrying out operations in close proximity. In addition, the engine cooling fan can come on at any moment.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (1/2) 3 2 4 5 6 1 7 Direction indicator lights/side lights and brake lights After opening the tailgate, open the flap of the light concerned. To remove the rear lights unit, undo nut 1. Release the rear light assembly from outside the vehicle by pulling towards the rear. To access the bulbs, unclip the bulb holder by pressing the two clips 2. 4 Direction indicator lights PY21 W bulb. Replace the bulbs. 5 Side light R5 W bulb. Clip bulb holder 2 back on.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (2/2) 8 9 10 High-level brake light 8 Number plate lights 9 Side indicator lights 10 Consult an approved Dealer. Unclip light 9 by pressing the tab. Unclip the side mounted indicator light (using a flat-blade screwdriver or similar). Remove the light cover to gain access to the bulb. Bulb type: C5W festoon bulb. Turn the bulb holder a quarter of a turn and take out the bulb. Bulb type: WY5W. The bulbs are under pressure and can break when replaced.
INTERIOR LIGHTS: changing bulbs (1/2) 1 1 1 2 Courtesy light Unclip the lens (using a flat-blade screwdriver or similar). Underfloor storage compartments lights 2 Remove the bulb concerned. Unclip the light (using a flat-blade screwdriver or similar). Bulb type 1: W5W. Turn the bulb holder a quarter of a turn and take out the lamp. Bulb type: W5W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
INTERIOR LIGHTS: changing bulbs (2/2) 4 3 Luggage compartment light Unclip light 3 by pressing the tabs on each side (using a flat-blade screwdriver or similar). 5 Press tab 4 to release the bulb holder and gain access to bulb 5. Bulb type: C5W festoon bulb. Disconnect the light. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
FUSES (1/2) 1 B A Fuse box Remove the fuse using tweezers 1, located on the cover. If any electrical equipment does not work, check the condition of the fuses. To remove the fuse from the tweezers, slide the fuse to the side. Unclip cover A or B (depending on vehicle). To identify the fuses, refer to the fuse allocation label (shown on the following page). Check the fuse in question and replace it, if necessary, with a fuse of the same rating.
FUSES (2/2) Allocation of fuses (the presence of fuses depends on the vehicle equipment level) Symbol Allocation Symbol 2 Rear electric windows and door locking x Manual air conditioning Ù Automatic wipe/wash Æ Cigar lighter ALIM UCH Main power supply n ABS N Central door locking h Electric windows g Heated door mirrors Z Courtesy lights f Windscreen wiper Ì Horn × Brake switch ï Injection î Radio Ò Instrument panel/air conditioning control panel t Automatic climate cont
BATTERY: troubleshooting (1/3) To avoid all risk of sparks: – Ensure that all electrical equipment is switched off before disconnecting or reconnecting the battery. – When charging, stop the charger before connecting or disconnecting the battery. – Do not place metal objects on the battery to avoid creating a short circuit between the terminals. A C B – Wait at least 20 seconds after switching off the engine to disconnect the battery. – Make sure that you reconnect the battery terminals after refitting.
BATTERY: troubleshooting (2/3) Connecting a battery charger The battery charger must be compatible with a battery with nominal voltage of 12 volts. Switch the engine off and then disconnect both battery leads starting with the negative terminal. Do not disconnect the battery when the engine is running. Follow the instructions given by the manufacturer of the battery charger you are using.
BATTERY: troubleshooting (3/3) Starting the vehicle using the battery from another vehicle Proceed as follows when starting your vehicle from another vehicle’s battery: Obtain suitable jump leads (large) from an approved Dealer or, if you already have jump leads, ensure that they are in perfect condition. The two batteries must have an identical nominal voltage of 12 volts. The battery supplying the current should have a capacity (amp-hours, Ah) which is at least the same as that of the discharged battery.
Radio frequency remote control: battery A A B 1 2 Remote controls A and B Replacing the battery 3 Note: It is not advisable to touch the electrical circuit in the key cover when replacing the battery. Remove screw 1. Open the case at slot 2 using a coin, and replace battery 3, observing the polarity shown on the back of the cover. When refitting, ensure that the cover is correctly clipped on and the screw tightened. B Batteries can be obtained from your approved Dealer.
FITTING THE RADIO 2 1 3 Radio location 1 Tweeter speakers Door speakers Unclip the blanking cover. The aerial, + and – supply and speaker wire connections are located behind it. Using a flat-blade screwdriver or similar, unclip grille 2 to access the speaker wires. Using a flat-blade screwdriver or similar, unclip grille 3 to access the speaker wires. – In all cases, it is very important to follow the manufacturer’s instructions carefully.
ACCESSORIES Before fitting an electrical or electronic device (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle. If you are using an anti-theft device, only attach it to the brake pedal. Contact an approved dealer for this information. Electrical and electronic accessories – Connect accessories with a maximum power of 120 Watts only. Use of transmission/ receiving devices (telephones, CB equipment etc.
WINDSCREEN WIPER BLADES 1 2 3 Replacing windscreen wiper blades 1 – With the ignition off, lift the wiper arm 3; – move blade 1 into a horizontal position; – slide blade 1 until catch 2 on the wiper arm is released. Refitting To refit the wiper blade, proceed in reverse order to removal. Make sure that the blade is correctly locked in position. Check the condition of the wiper blades.
TOWING: breakdown Access to towing points Unclip cover 3 or 5 using a flat-blade screwdriver or similar. 1 2 1 Screw in towing hitch 1 fully: as much as possible by hand at first, then finish by tightening it using the wheelbrace. 4 5 3 Insert the key into the ignition switch to unlock the steering wheel and to use the indicator lights (brake lights, indicators, etc.). The towed vehicle’s lights must be switched on at night.
TOWING: breakdown (continued) Towing a vehicle with an automatic gearbox Towing a vehicle with a Quickshift gearbox With the engine switched off: the gearbox is no longer lubricated. It is preferable to tow this type of vehicle on a trailer or tow it with the front wheels off the ground.
Towing: equipment A Permissible nose weight, maximum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. For fitting and conditions of use, refer to the equipment’s fitting instructions. Please keep these instructions with the rest of the vehicle documentation. A: 614 mm (normal chassis) A: 681 mm (long chassis) 5.
Operating faults (1/5) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved Dealer as soon as possible. The starter is activated POSSIBLE CAUSES WHAT TO DO The indicator lights fail to light up and the starter does not turn. Battery terminals disconnected, oxidised or incorrectly secured. Retighten, reconnect or clean them if they are oxidised. Battery discharged or unserviceable.
Operating faults (2/5) On the road POSSIBLE CAUSES WHAT TO DO Coolant boiling in the coolant reservoir. Mechanical fault: cylinder head gasket damaged, faulty coolant pump. Stop the engine. Contact an approved Dealer. Smoke under the bonnet. Short circuit or cooling system leak. Stop, switch off the ignition, stand away from the vehicle and contact an approved Dealer. while cornering or braking The level is too low.
Operating faults (3/5) On the road POSSIBLE CAUSES WHAT TO DO Vibrations Tyres not inflated to correct pressures, incorrectly balanced or damaged. Check the tyre pressures: if this is not the problem, have them checked by an approved dealer. whistling roof aerial incorrectly positioned Fold down the aerial until the end of it is approximately 44 cm from the vehicle’s roof. Steering becomes heavy. Assistance overheating. Leave to cool. Low battery. Recharge or replace the battery.
Operating faults (4/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved Dealer. The wiper does not stop. Faulty electrical controls. Consult an approved Dealer. Direction indicators flashing more quickly. Blown bulb. Replace the bulb. The direction indicators do not work. Faulty electrical circuit. Consult an approved Dealer.
OPERATING FAULTS (5/5) Electrical equipment The sunroof does not open/close. POSSIBLE CAUSES WHAT TO DO Sunroof opening conditions not fulfilled. Apply the opening conditions (refer to the information on the “Electric sunroof” in Section 3). Roof fault. Leave the sunroof closed or close it using the methods described in “Electric sunroof: Operating fault” in Section 3 and contact your approved dealer. Electrical fault (discharged battery, etc.). 5.
5.
Section 6: Technical specifications Vehicle identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine specifications. . . . . . . . . . . .
VEHICLE IDENTIFICATION plates A 1 2 3 4 5 A The information shown on the vehicle identification plate should be quoted on all correspondence or orders. The presence and location of the information depends on the vehicle. B 6.2 Vehicle identification plate A 1 Vehicle type and chassis number. Depending on the vehicle, this information is also given on marking B. 2 MMAC (Maximum permissible all-up weight). 3 GTW (Gross train weight: vehicle fully loaded, with trailer).
ENGINE IDENTIFICATION plates A 1 2 A A 3 The information on the engine plate or label A should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. A 6.
Dimensions (in metres) Standard chassis 0.802 2.482 0.590 1.472 3.874 Long chassis 1.589* 0.802 2.575 4.034 * 6.4 Unladen 0.657 1.450 1.
ENGINE SPECIFICATIONS Versions Engine type (see engine plate) Cubic capacity (cc) Type of fuel Octane rating 1.2 16V 1.2 16V TCE 1.4 16V 1.6 16V 1.5 dCi D4F D4F Turbo K4J K4M K9K Turbo 1 390 1 598 1 461 1 149 It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap.
weights (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer.
Replacement parts and repairs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
Service sheets VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (continued) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (continued) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (continued) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (continued) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (continued) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
Anticorrosion check If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Alphabetical index (1/5) A ABS.................................................................................... 2.14 accessories........................................................................ 5.30 accessories socket............................................................. 3.29 additional methods of restraint........................................... 1.26 side protection.............................................................. 1.25 to the front seat belts................................
Alphabetical index (2/5) E electric windows................................................................. 3.17 Electronic Stability Program: ESP........................... 2.15 – 2.16 emergency brake assist..................................................... 2.19 emergency braking............................................................. 2.19 emergency spare wheel.............................................5.2 → 5.5 engine technical specifications...................................................
Alphabetical index (3/5) J jack....................................................................................... 5.9 K keys............................................................................1.2 → 1.5 L levels.................................................................................... 4.8 levels: brake fluid....................................................................... 4.9 coolant............................................................................ 4.
Alphabetical index (4/5) functions....................................................................... 3.35 rear view mirrors...................................................... 1.64 – 1.65 replacement parts................................................................. 6.7 reverse gear selecting.......................................................................... 2.8 roof bars............................................................................. 3.40 roof rack roof bars..................
Alphabetical index (5/5) washing................................................................... 4.12 – 4.13 wheelbrace........................................................................... 5.9 wheels (safety).......................................................5.13 → 5.15 windscreen de-icing/demisting........................................... 3.13 windscreen washer.................................................1.73 → 1.75 wiper blades............................................................
( www.renault.ie ) ( www.renault.co.uk ) ( www.renault.is ) RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
