SCENIC DRIVER’S HANDBOOK
RENAULT recommends ELF ELF has developed a complete range of lubricants for RENAULT: f engine oils f manual and automatic gearbox oils Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please refer to your maintenance document. Benefiting from the research applied to Formula 1, lubricants are very high-tech products.
Welcome to your new vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections ............................... 1 ................................................................... 2 Your comfort . ........................................................ 3 Maintenance 4 Getting to know your vehicle Driving .......................................................... Practical advice ..................................................... . ..................................... 6 ................................................
0.
Section 1: Getting to know your vehicle RENAULT cards: general information, use, deadlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic locking of opening elements when driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seat belts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RENAULT cards: general information (1/2) The RENAULT card is used for: 1 1 2 3 4 5 2 3 4 5 Unlocking the doors and tailgate. Locking all doors and tailgate. Switching on the lighting remotely. Unlocking/locking the tailgate Integrated key. Special note The RENAULT “SERVICE” card, on equipped vehicles, can be identified by the word “SERVICE” engraved on the card. Refer to the information on the RENAULT “SERVICE” card in section 1. 1.
RENAULT cards: general information (2/2) Access to key 5 Press button 6 and pull on key 5 then release the button. 5 6 Using the key Refer to the information on “Locking/ unlocking the doors”. Once you have accessed the vehicle using the integrated key, replace it in its housing in the RENAULT card, then insert the RENAULT card into the card reader to start the vehicle.
Remote control RENAULT card: use 2 1 3 4 Unlocking the doors and tailgate Press button 1. The hazard warning lights flash once to indicate that the doors have been unlocked. When unlocking is only active for the driver’s door, (refer to the information on the “vehicle settings customisation menu” in Section 1): – pressing button 1 unlocks only the driver’s door and the fuel filler flap; – pressing button 1 twice unlocks all the doors and the tailgate.
RENAULT “hands-free” card: use (1/3) 2 3 1 Use Unlocking the vehicle Note: ensure that the RENAULT card is not in contact with other electronic equipment (computer, PDA, phone, etc.) as this could hinder its operation. Pressing the button 3 also unlocks all the doors and the tailgate. On equipped vehicles, in addition to the functions of the remote control RENAULT card, it can be used to lock and unlock without using the RENAULT card, when it is in access zone 1.
RENAULT “hands-free” card: use (2/3) Locking using button 4 If you want to lock your vehicle, the card must be nearby (garage adjacent etc.), with the door and tailgate closed, press button 4 on the handle of the driver’s door. The vehicle will lock. If a door or the tailgate is open or not properly closed, the vehicle will quickly lock/ unlock. 4 1 Note: a RENAULT card must be within the vehicle's access zone (zone 1) to be able to lock the vehicle using the button.
RENAULT “hands-free” card: use (3/3) 5 6 With the engine running, if after having opened and closed a door the card is no longer in the passenger compartment, the message Keycard not detected (accompanied by a beep when the speed exceeds a certain level) warns you that the card is no longer in the vehicle. This prevents you driving away after having dropped off a passenger who has the card, for example. The warning disappears when the card is detected again.
RENAULT CARD: deadlocking To deactivate deadlocking 1 2 If the vehicle is equipped with a deadlocking function, this allows you to lock the opening elements and to prevent the doors from being unlocked using the interior handles (for example, by breaking the window and then trying to open the door from the inside). Unlock the vehicle using button 1 on the RENAULT card.
RENAULT “service” card 1 Deactivation of the “SERVICE” mode 2 There are two possibilities: – press a button on the RENAULT card (not the RENAULT “SERVICE” card); 3 If the vehicle is equipped with this card, it can be identified by the word “SERVICE” printed on the card. In certain situations, you may wish to entrust your vehicle to a third party (parking valet, mechanic, etc.) whilst restricting its operation.
Opening and closing the doors (1/2) Card reminder buzzer 1 2 When the driver’s door is opened and the card is still in the reader, the message “Please remove keycard” appears on the instrument panel, accompanied by a beep. Door/tailgate open buzzer Opening the doors from the outside With the doors unlocked or the RENAULT “hands-free” card in your possession, hold handle 1 and pull it towards you. In some cases, it may be necessary to pull the handle twice to open the door.
Opening and closing the doors (2/2) 3 Child safety Ç Vehicle with switch 3 Press switch 3 to authorise opening of the rear doors. If the vehicle is equipped with electric rear windows, this action will also authorise their use. The indicator light in the switch lights up to confirm that the locks have been activated. Note: if there is a system fault, the message “Check child safety device” is displayed on the instrument panel: contact an approved Dealer.
locking/unlocking the DOORS (1/2) Locking/Unlocking the doors from the outside This is done using the RENAULT Card; see the “RENAULT Card” information in Section 1. 2 In certain cases, the RENAULT card may not work: – when the RENAULT card battery is drained, flat battery, etc. – use of appliances operating on the same frequency as the card (mobile phone, etc.); – vehicle located in a high electromagnetic radiation zone.
locking/unlocking the DOORS (2/2) 3 Interior locking/unlocking door control Locking the doors without the RENAULT card Door and tailgate status indicator For example, in the event of a discharged battery or the RENAULT card temporarily not working, etc. When the ignition is on, the indicator light integrated in switch 3 informs you of the status of the doors and tailgate: With the engine switched off and a door or the tailgate open, press and hold switch 3 for more than five seconds.
Automatic locking when driving Activating/deactivating the function 1 Operating principle After the vehicle is started, the system automatically locks the doors when you are driving at approximately 6 mph (10 km/h) and over. To activate: with the vehicle stopped and the engine running, press switch 1 until a beep sounds. To deactivate: with the vehicle stopped and the engine running, press switch 1 until two beeps sound.
Front headrests To adjust side supports B 2 A B To remove the headrest B 1 Depending on the vehicle, sections B can be adjusted independently to the desired position. 3 Raise it to its highest position (tilt the seatback backwards if necessary). Press button 1 on each rod 3 and lift it until it is released. To refit the headrest To raise the headrest Pull the headrest upwards to the desired height. To lower the headrest Press button 2 and guide the headrest down to the desired height.
Front seats with manual control (1/2) 4 2 1 3 To move the seat forwards or back Lift handle 1 to release. Release the handle at the desired position and make sure that it is locked. To raise or lower the seat base Move lever 2 as many times as necessary upwards or downwards. 1.16 To tilt the seatback Turn control knob 3 to the required position. To adjust the lumbar support on the driver’s seat Lower handle 4 to increase the support and lift it to decrease it.
Front seats with manual control (2/2) 5 6 Table function Depending on the vehicle, the passenger seatback may be folded down onto the seat base to create a table. Lower the headrest if necessary, tilt handle 5 and completely lower the seatback. Heated seats (depending on vehicle) With the engine running, turn control 6 to either position 1, 2 or 3 (depending on the temperature required). An indicator light on the instrument panel lights up once the front seat heating system is operating.
DRIVER’S SEAT WITH ELECTRIC CONTROLS Switch 4 is used for adjusting the seat base and switch 3 is used for adjusting the seatback. On equipped vehicles, buttons 2 store the chosen driving position (refer to the following page). 5 2 Adjusting the seat position To move the seat forwards or back Move switch 4 forwards or backwards. To raise or lower the seat base Move switch 4 upwards or downwards. 3 1 4 Adjusting the seatback To tilt the seatback, move the top of switch 3 forwards or backwards.
Driver’s seat with position memory Recalling a stored driving position It is possible to store three driving positions. A driving position includes the settings for the seat base and seatback of the driver’s seat. With the vehicle stationary, briefly press button 1, 2 or 3 depending on the required stored driving position.
Seat belts (1/3) Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in. Before starting, first adjust your driving position, then ask all occupants to adjust their seat belts to ensure optimum protection. Adjusting your driving position Make sure that the rear seats are locked in position properly so that the rear seat belts will operate efficiently.
Seat belts (2/3) ß 1 3 5 4 5 Locking Unwind the belt slowly and smoothly and ensure that buckle 3 locks into catch 5 (check that it is locked by pulling on buckle 3). If the belt jams, allow it to return slightly before attempting to unwind it again. If your seat belt is completely jammed, pull slowly, but firmly, so that just over 3 cm unwinds. Allow it to return slightly before attempting to unwind it again. If there is still a problem, contact an approved dealer.
Seat belts (3/3) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident.
REAR SEAT BELTS Second row centre rear seat 2 Unwind belt 2 slowly from its housing. 1 3 9 8 6 10 Click buckle 4 into black catch 5. Snap last sliding buckle 6 into the red catch 7. 4 7 On equipped vehicles, for your comfort, you can pass the belt through belt guide 3. 12 5 Second row rear side seats Third row rear seats (7-seater versions) Slowly unwind belt 1. Slowly unwind the belt 10. Fasten sliding buckle 9 into corresponding red catch 8.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they are composed of: – seat belt inertia reel pretensioners; – Have the entire restraint system checked following an accident. – No operation whatsoever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical. – lap belt pretensioners; – chest-level load limiter; – air bags for driver and front passenger.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. Air bags for driver and front passenger Fitted to the driver and passenger side. A The presence of this equipment is indicated by the word “Air bag” on the steering wheel and dashboard (air bag zone A) and, depending on the vehicle, a symbol on the lower section of the windscreen.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operation This system is only operational when the ignition is switched on. In a severe frontal impact, the air bags inflate rapidly, cushioning the impact of the driver’s head and chest against the steering wheel and of the front passenger against the dashboard. The air bags then deflate immediately so that the passengers are not in any way hindered from leaving the vehicle. 1.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
Methods of restraint in addition to the rear seat belts Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. – Have the entire restraint system checked following an accident. – No operation whatsoever is permitted on any part of the system (air bags, electronic control units, wiring) and the system components must not be reused on any other vehicle, even if identical.
Side protection devices Side air bags These air bags are fitted to the front seats and are activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Curtain air bags These are air bags fitted along the sides of the vehicle in the ceiling which trigger along the front and rear side windows to protect the passengers in case of a severe side impact.
Additional methods of restraint All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times.
Child safety: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.
Child safety: General information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to restrain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact. Before purchasing a child seat, check that it complies with the regulations for the country you are in and that it can be fitted in your vehicle.
Child safety: Choosing a child seat Rear-facing child seats A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell. Forward-facing child seats The child’s head and abdomen need to be protected as a priority.
child safety: choosing a child seat mounting (1/2) There are two ways of attaching child seats: via the seat belt or using the ISOFIX system. Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected. Always check that the seat belt is correctly fastened by pulling it up, then pulling it out fully whilst pressing on the child seat.
child safety: choosing a child seat mounting (2/2) 1 2 Attachment using the ISOFIX system (continued) The two rings 1 are located between the seatback and the seat base of the seat and are identified by a marking. To ensure your child seat can be easily fitted and locked on the rings 1, use access guides 2 on the child seat. 4 3 6 5 The third ring 3, 4 and 5 (for long chassis versions) or 6 (for short chassis versions) is used to attach the upper strap on some ISOFIX seats.
child safety: fitting a child seat (1/11) Some seats are not suitable for fitting child seats. The diagram on the following page shows you how to attach a child seat. The types of child seats indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. Fit the child seat in a rear seat wherever possible. Check that when installing the child seat in the vehicle it is not at risk of coming loose from its base.
child safety: fitting a child seat (2/11) In the rear seat In the rear centre seat A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest the door. Some child seats are too wide to allow access to the seat belt buckles. Check that your child seat can be fitted in this seat.
child safety: fitting a child seat (3/11) Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. Installation diagram, 5-seater short chassis version ³ ² Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat. seats. Seat not suitable for fitting child Child seat attached using the belt ¬ − Seat which allows a child seat with “Universal” approval to be attached by a seat belt.
child safety: fitting a child seat (4/11) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
child safety: fitting a child seat (5/11) Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchoring points are visible on the floor behind the seat concerned or under the carpet, and indicated by a marking.
child safety: fitting a child seat (6/11) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
child safety: fitting a child seat (7/11) Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchoring points are located on the floor behind the seat concerned and indicated by a marking.
child safety: fitting a child seat (8/11) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
child safety: fitting a child seat (9/11) X =S eat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted.
child safety: fitting a child seat (10/11) Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchoring points are visible on the floor behind the seat concerned or under the carpet, and indicated by a marking.
child safety: fitting a child seat (11/11) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
child safety: deactivating/activating the front passenger air bag (1/3) A 1 The front passenger air bag must only be deactivated or activated when the vehicle is stationary. If it is interfered with when the vehicle is being driven, indicator lights å and © will come on. Switch the ignition off then on again to reset the air bag in accordance with the lock position.
child safety: deactivating/activating the front passenger air bag (2/3) A A 3 The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag. The child may suffer very serious injuries if the air bag is triggered. 1.
child safety: deactivating/activating the front passenger air bag (3/3) Operating faults A 1 It is not permitted to fit a rear-facing child seat to the front passenger seat if the air bag activation/deactivation system is faulty. It is not recommended to allow any other passenger to sit in that seat if the › ¹ two warning lights are lit at the same time. and Contact your approved dealer as soon as possible.
Driving position: left-hand drive (1/2) 1 2 3 27 4 25 24 26 5 6 7 8 9 10 11 12 23 22 21 18 17 19 20 1.
Driving position: left-hand drive (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vent. 2 Side window demister outlet. 3 Stalk for: – direction indicator lights; – exterior lights; – front fog lights; – rear fog light. 4 Location for driver’s air bag and horn. 5 – Steering column stalk for windscreen and rear screen wash/ wipe. – Trip computer information readout control and vehicle settings personalisation menu. 6 Instrument panel. 7 Centre air vents.
Driving position: right-hand drive (1/2) 1 2 3 27 26 1.
Driving position: right-hand drive (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vent. 11 Stalk for: 2 Side window demister outlet. – direction indicator lights; 3 Location for passenger air bag. – exterior lights; 4 Centre air vents. – front fog lights; 5 – Display (depending on the vehicle) for time, temperature, radio information, navigation system information, etc. – rear fog light.
Instrument panel: warning lights (1/5) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Φ 1 A B Speed limiter and cruise control indicator lights See the information on the “Speed limiter” and “Cruise control” in Section 2. The ® warning light requires you to stop immediately, for your own safety, as soon as traffic conditions allow. Switch off the engine and do not restart it. Contact an approved Dealer.
Instrument panel: warning lights (2/5) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Ä B A u k á g f Side light tell-tale light Dipped beam headlight telltale light Main beam headlight tell-tale light Front fog light tell-tale light Rear fog light tell-tale light Automatic main beam headlight indicator light Please refer to the information on “External signals and lights” in Section 1.
Instrument panel: warning lights (3/5) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. } Handbrake “on” or electronic parking brake warning light Refer to the information on the “Handbrake” or “Electronic parking brake” in Section 2. ß Driver’s seat belt reminder and, depending on the vehicle, front passenger seat belt reminder.
Instrument panel: warning lights (4/5) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. © Warning light It requires you to stop immediately, for your own safety, as soon as traffic conditions allow. Switch off the engine and do not restart it. This lights up when the ignition is switched on and goes out after approximately three seconds. It can light up in conjunction with other warning lights and/or messages on the instrument panel.
Instrument panel: warning lights (5/5) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. The following warning lights come on accompanied by the ® warning light. D Brake circuit fault warning light If it comes on during braking and is accompanied by the ® warning light and a beep, it indicates that the fluid level in the circuit is low or that there is a braking system fault. Stop as soon as traffic conditions allow and contact an approved Dealer.
Displays and indicators (1/4) Rev counter (rpm × 1,000) This is displayed according to how the instrument panel is customised. A 2 3 Speedometer (km/h or mph) Fuel gauge 1 2 “TFT Display instrument panel” A You may customise your instrument panel A with content and colours of your choice. Press switch 1 repeatedly to obtain the desired display. The remaining fuel level is shown in yellow. M If the level is at the minimum, the warning light integrated in the indicator comes on, accompanied by a beep.
Displays and indicators (2/4) 3 5 4 Instrument panel in miles (option to switch to km/h) – With the ignition off, press button 3 or 4 and start button 5; – the speedometer unit indicator flashes for approximately ten seconds, then the new unit is displayed: release button 3 or 4 when the unit stops flashing. To return to the previous mode, repeat the same operation. Note: once the battery is switched off, the trip computer and warning system automatically returns to the original unit of measurement. 1.
Displays and indicators (3/4) 6 7 8 B Vehicle without “TFT Display” instrument panel Instrument panel B Fuel level gauge 6 M If the level is at the minimum, the warning light integrated in the indicator comes on, accompanied by a beep. Fill up as soon as possible.
Displays and indicators (4/4) 2 3 4 Instrument panel in miles (option to switch to km/h) – With the ignition off, press button 3 or 4 and start button 5. – The speedometer unit flashes for approximately ten seconds, then the new unit is displayed: release button 3 or 4 when the unit stops flashing. To return to the previous mode, repeat the operation. Note: once the battery is switched off, the trip computer and warning system automatically returns to the original unit of measurement. 1.
TRIP COMPUTER: general information (1/2) c) mileage before service; 1 d) tyre pressure monitor; 2 e) cruise control/speed limiter programmed speed (only for vehicles which are not equipped with a “TFT Display” instrument panel); f) on-board log, operating fault and information message readout.
ON-BOARD COMPUTER: general information (2/2) 2 3 Trip mileage resetting With “trip mileage recorder” selected on the display, press button 2 or 3 until the mileage recorder resets to zero. Resetting the journey parameters (reset button) With one of the journey parameters selected on the display, press button 2 or 3 until the display resets. 1.
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (1/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected a) Total mileage and trip mileage recorder. Fuel used 8L Fuel consumption A B L/100 b) Journey parameters. Fuel used. Fuel consumed since the last reset. Current fuel consumption A. This value is displayed above a speed of approximately 18 mph (30 km/h).
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (2/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Range 541km Distance 522km Average 123.4km/H 1.66 Interpreting the display selected Estimated range with remaining fuel. The value is displayed after driving 400 metres. Distance travelled since the last reset. Average speed since the last reset. The value is displayed after driving 400 metres.
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (3/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Oil change in 1936 km/2 mo. Interpreting the display selected c) Mileage before oil change.
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (4/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected d) Tyre pressure monitor. Refer to the information on the “Tyre pressure monitor” in Section 2. Speed limiter 90.km/H Cruise control e) Cruise control/speed limiter programmed speed (only for vehicles which are not equipped with a “TFT Display” instrument panel).
TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages “Parking brake on” Interpreting the display selected Indicates that the parking brake has been applied. “Please remove keycard” Request to remove the RENAULT card from the reader when you leave the vehicle.
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The © warning light stays on. Examples of operating fault messages are given in the following pages.
TRIP COMPUTER AND WARNING SYSTEM: warning message These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
Vehicle settings customisation menu Adjusting the settings 1 4 2 3 On equipped vehicles, this function, which is integrated in trip computer and warning system 1, allows you to activate/deactivate and adjust some of the vehicle’s functions. Accessing the vehicle settings personalisation menu With the vehicle stationary, press button 2, 3 or 4 to access the various settings. 1.
Steering wheel/power-assisted steering Power-assisted steering Variable power-assisted steering The variable power-assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. 1 Operating faults The steering may become stiff when driving or when the steering wheel is turned repeatedly. This is due to the power assistance overheating. In this case, it must be allowed to cool down.
Clock and exterior temperature (1/2) 1 Vehicles fitted with a navigation system 2 For vehicles which are fitted with this equipment, please refer to the specific equipment instructions for details of their special features. 3 4 5 Resetting the clock 1 Vehicles fitted with control 3 – Press and hold button 2 for approximately three seconds; Select “clock” from the vehicle settings customisation menu (see previous page). Press button 4 to scroll through the hours and button 5 to confirm.
Clock and exterior temperature (2/2) External temperature indicator Special note: When the exterior temperature is - 3 °C to + 3 °C, the °C characters flash (signalling a risk of ice on the road). External temperature indicator As ice formation is related to climatic exposure, local air humidity and temperature, the external temperature alone is not sufficient to detect ice. 1.
Rear view mirrors Folding door mirrors A B 1 3 C D E 2 The door mirrors automatically fold in when the vehicle is locked (switch 2 in position D). In this case, they will fold out when the ignition is next switched on. In any case, you can make the door mirrors fold in (switch 2 in position E) or out (switch 2 in position C). Automatic mode is then deactivated. To reactivate it, set switch 2 to D. 4 Door mirrors Interior rear view mirror Adjustment Its position can be adjusted.
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. 1 A Horn Press on the sides of the steering wheel boss A. Headlight flasher Pull stalk 1 towards you to flash the headlights. 2 When driving on the motorway, the steering wheel is not often turned enough to return the stalk automatically to 0. There is an intermediate position which automatically triggers a series of three flashes.
Exterior lighting and signals (1/5) á 1 2 1 Main beam headlights With the dipped beam headlights lit, pull stalk 1 towards you. This indicator light on the instrument panel comes on. To return to the dipped headlight position, pull stalk 1 towards you again. 3 u Side lights Turn ring 3 until the symbol is opposite mark 2. This indicator light on the instrument panel comes on.
Exterior lighting and signals (2/5) Automatic main beam headlights This system switches the main beam headlights on and off automatically. The function uses a camera located behind the interior rear-view mirror to detect vehicles that are following and coming in the opposite direction. The main beam headlights come on automatically if: – exterior light is weak; – no other vehicles or lighting are detected; – vehicle speed is greater than 30 mph (45 km/h).
Exterior lighting and signals (3/5) Directional headlights 1 2 Depending on the vehicle, with the dipped beam headlights on and under certain conditions (speed, steering wheel angle, forwards gear selected, etc.) when cornering, the dipped beam headlights move to light the inside of the bend. Special features 3 Daytime running lights function Depending on the vehicle, the daytime running lights come on (only at the front) without starting the engine.
Exterior lighting and signals (4/5) “See-me-home lighting” function This function allows you to briefly switch on the dipped beam headlights (to provide light when opening a gate, etc.). Lights-on reminder buzzer If the lights are on after the engine is switched off, a warning beep sounds when the driver’s door is opened to warn you that the lights are still on.
Exterior lighting and signals (5/5) g 1 4 Front fog lights Turn centre ring 5 on stalk 1 until the symbol faces mark 4, then release it. Operation of the fog lights depends on the exterior lighting position selected, and an indicator light will light up on the instrument panel. 5 f Switching off the lights Turn ring 5 again until mark 4 is opposite the symbol for the fog light that you wish to switch off. The corresponding indicator light on the instrument panel goes out.
Electrical adjustment of the dipped beam headlights For manual settings Examples of positions for adjusting control A according to the load A On vehicles fitted with this function, control A allows you to adjust the height of the beams according to the load. Turn control A downwards to lower the headlights and upwards to raise them. For vehicles not fitted with control A, adjustment is automatic.
Windscreen wiper, washer (1/2) Vehicle fitted with front windscreen wiper rain sensor 1 E 1 2 A D B C F A park B automatic wiper function When this position is selected, the system detects water on the windscreen and triggers the wipers at a suitable wiping speed.
Windscreen wiper, washer (2/2) Headlight washers 1 A D B C Windscreen washer Headlights on On equipped vehicles, hold stalk 1 pulled towards you for about 1 second, and the headlight washers and windscreen washers will be activated at the same time. Note: when the minimum windscreen washer fluid level is reached, the headlight washer system may be deprimed. Fill the windscreen washer fluid and then activate the windscreen washer, with the engine running, to reprime the system.
Rear screen wash/WIPE 1 Activating/deactivating the rear screen wiper (depending on the vehicle) A 2 Y Rear screen wiper With the ignition on, turn ring A on stalk 1 to align the symbol with mark 2 then release it. To stop the operation, pivot ring A again. Wiping frequency varies with vehicle speed. If your vehicle is fitted with a vehicle settings customisation menu, it is programmed to activate the rear wipers when reverse gear is selected (if the windscreen wipers are on).
Fuel tank (1/3) Fuel grade Use a high-grade fuel that complies with the legislation in force in each country and which must conform to the specifications given on the label on cover B. Please refer to the information on “Engine specifications” in Section 6. B A C Diesel versions It is essential to use diesel fuel that conforms with the information given on the label inside cover B. Useable fuel tank capacity: 60 litres approximately.
Fuel tank (2/3) Filling with fuel With the ignition off, insert the nozzle to open valve A and insert it fully before turning it on to fill the fuel tank (risk of splashing). 1 Keep the nozzle in this position throughout the entire filling operation. When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts may be made, as there must be sufficient space in the fuel tank to allow for expansion.
Fuel tank (3/3) 2 Running out of fuel on diesel versions (depending on vehicle) After a breakdown caused by completely running out of fuel, the system must be reprimed before the engine is restarted: Fill the tank with at least 8 litres of diesel fuel. Press priming bulb 2 several times. The engine can now be restarted. If the engine does not start after several attempts, contact an approved Dealer.
1.
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starting/Stopping the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop and Start Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RUNNING IN Petrol version Diesel version Up to 600 miles (1,000 km), do not exceed 78 mph (130 km/h) in top gear or 3,000 to 3,500 rpm. For the first 900 miles (1,500 km), do not exceed 2,500 rpm. After completing this mileage you may drive faster, however, it is only after approximately 3600 miles (6,000 km) that you may reasonably expect full performance. You may only expect top performance from your vehicle after approximately 1,800 miles (3 000 km).
Starting/stopping the engine (1/3) Starting the vehicle – For vehicles with automatic gearboxes, set the lever to the P position. 1 2 Remote control RENAULT card When you get into the vehicle, insert the RENAULT card fully into card reader 2. To start, press button 1. If a gear is engaged, depress the clutch pedal to start the vehicle. 3 RENAULT “hands-free” card The RENAULT card must be inserted in card reader 2 or in detection zone 3. To start, depress the brake or clutch pedal and press button 1.
Starting/stopping the engine (2/3) For other functions: – vehicles with remote control RENAULT card, insert the card into reader 2; 1 – vehicles with a RENAULT “handsfree” card, with the card in the passenger compartment or inserted in the card reader 2, press button 1 without depressing the pedals. 2 Note: if there is a card in the reader, pressing button 1 starts the engine. (switching on the ignition) 2.
Starting/stopping the engine (3/3) Special note If the card is no longer in the reader when you try to switch the engine off, the message “No keycard Press and hold” appears on the instrument panel: press button 1 for longer than two seconds. 1 When you leave your vehicle, especially if you have your RENAULT card with you, check that the engine is completely switched off.
Stop and Start function (1/3) This system enables a reduced fuel consumption and lower greenhouse gas emissions. The system is activated automatically when the vehicle is started. While driving, the system stops the engine (standby) when the vehicle is at a standstill (traffic jam, traffic lights, etc.) Warning light is displayed on the instrument panel. This notifies you that the engine is on standby. The vehicle equipment remain operational while the engine is stopped.
Stop and Start function (2/3) Conditions preventing the standby of the engine Certain conditions prevent the system from using the engine standby function, including when: – the “Clear View” function is activated (please see “Automatic Climate Control” in Section 3); – the engine coolant temperature is too low; – the driver’s door is not closed; – automatic particle filter cleaning is underway; or – ...
Stop and Start function (3/3) The system is automatically reactivated each time the vehicle is started using the start button (please see “Starting, stopping the engine)”. 1 Operating faults When the message “Check Stop & Start” appears on the instrument panel and the integrated warning light 2 lights up on the switch 1, the system is deactivated. Please consult an authorised dealer. 2 Deactivating, activating the function Press 1 to deactivate the function.
Special features of petrol versions The following operating conditions should be avoided: – driving for long periods when the low fuel level warning light is lit; – using leaded petrol; – using fuel or lubrication additives which are not approved.
Special features of diesel versions Diesel engine speed Diesel engines are fitted with injection equipment which prevents the engine speed being exceeded irrespective of the gear selected. If the message “Check anti-pollution system” is displayed on the instrument Ä and panel accompanied by the © warning light; consult an approved dealer straight away.
Gear lever/Handbrake Handbrake 1 To release: Pull lever 2 up slightly, press button 3 and then lower the lever to the floor. To apply: 3 Pull the lever 2 upwards and make sure the vehicle is immobilised. 2 Make sure that the handbrake is properly released when driving (red indicator light off), otherwise overheating may occur. Selecting reverse gear Vehicles with manual gearbox: follow the grid drawn on knob 1, and depending on the vehicle, lift ring against the gear lever knob to select reverse.
ELECTRONIC PARKING BRAKE (1/3) Note: 1 2 3 To indicate that the electronic parking brake is applied or released, a beep sounds and the message “Apply parking brake” appears on the instrument panel: – with the engine running: when the driver’s door is opened; – with the engine switched off (eg. when the engine stalls): when a front door is opened. In this case, pull and release switch 3 to apply the electronic parking brake.
ELECTRONIC PARKING BRAKE (2/3) Special cases When parking on a slope or towing a trailer, pull switch 3 for a few seconds to obtain the maximum braking effect.
ELECTRONIC PARKING BRAKE (3/3) Versions with an automatic gearbox For safety reasons, automatic release is deactivated when the driver’s door is open or not properly closed and the engine is running (in order to prevent the vehicle from moving without the driver). The message “Release parking brake manually” appears on the instrument panel when the driver depresses the accelerator. Never leave your vehicle without moving the selector lever to position P or N.
Advice: antipollution, fuel economy and driving (1/3) Your vehicle complies with criteria for recycling and recovering vehicles at the end of their service life which will come into force in 2015. Some parts of your vehicle have therefore been designed to facilitate future recycling. These parts are easy to remove so that they can be recovered and reprocessed by recycling companies.
Advice: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring system – Sporty driving uses a lot of fuel: drive with a light right foot. – Brake as little as possible. If you anticipate an obstacle or bend in advance, you may then simply release the accelerator pedal. – Do not try to maintain the same speed up a hill, accelerate no more than you would on the level. Keep your foot in the same position on the accelerator pedal.
Advice: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air conditioning, it is normal to observe an increase in fuel consumption (especially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Environment Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. This commitment is illustrated by the Renault eco² group signature.
Tyre pressure monitor (1/4) If the vehicle is equipped with the function, this system monitors the tyre pressure. 1 Operating principle Each wheel (except for the emergency spare wheel) has a sensor in the inflation valve which periodically measures the tyre pressure. The system informs the driver via the trip computer and warning system 1 that the tyres are sufficiently inflated and warns if they are underinflated or leaking. Never deflate a hot tyre.
Tyre pressure monitor (2/4) “Tyre pressure sensors absent” or “Check tyre pressure sensors” One wheel B disappears, indicating that the sensor on this wheel is missing or faulty (e.g. if the emergency spare wheel is fitted). B A C vehicles without “TFT display” instrument panels A “Inflate tyres for motorway” The tyre pressure is not suitable for the speed of travel. Slow down or inflate all four tyres to motorway pressure (refer to the information on “Tyre pressures”).
Tyre pressure monitor (3/4) 3 4 3 D E “Inflate tyres for motorway” The wheel concerned E is shown in orange on display 4. The tyre pressure is not suitable for the speed of travel. Slow down or inflate all four tyres to motorway pressure (refer to the information on “Tyre pressures” in Section 4). “Adjust tyre pressure” The wheel concerned E is shown in orange on display 4 and indicates a flat tyre. Display 3 reminds you of this information.
Tyre pressure monitor (4/4) Replacing wheels/tyres This system requires specific equipment (wheels, tyres, hubcaps, etc.). Contact an approved Dealer to fit new tyres and to find out about available accessories compatible with the system and available from your dealer network: the use of any other accessory could affect the correct operation of the system or damage a sensor. Emergency spare wheel If the vehicle is equipped with an emergency spare wheel, it will not have a sensor.
Driver correction devices AND aids (1/4) Depending on the vehicle, this is composed of: – the ABS (anti-lock braking system); – the electronic stability program ESP with understeer control and traction control ASR; – emergency brake assist with, depending on the vehicle, braking anticipation. These functions are an additional aid in the event of critical driving conditions, enabling the vehicle behaviour to be adapted to suit the driving conditions.
Driver correction devices AND aids (2/4) Electronic stability program ESP with understeer control and traction control ASR Electronic stability program ESP This system helps you to keep control of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip on a bend, etc.). Operating principle A sensor in the steering wheel detects the direction selected by the driver. Other sensors throughout the vehicle measure the actual direction.
Driver correction devices AND aids (3/4) 1 The traction control ASR offers additional safety, it is recommended that you do not drive with the function disabled. Correct this as soon as possible by pressing switch 1 again. Note: the function is reactivated automatically when the ignition is switched on or when a speed of approximately 24 mph (40 km/h) is exceeded. Emergency brake assist This system supplements the ABS and helps reduce vehicle stopping distances.
Driver correction devices AND aids (4/4) Hill start assistance This device assists the driver when starting on hills (ascending or descending). It prevents the vehicle from rolling backwards by automatically applying the brakes when the driver lifts his/her foot off the brake pedal to depress the accelerator pedal.
Lane departure warning system (1/2) This lane departure warning system notifies the driver when they accidentally cross a continuous or broken line. This function uses a camera attached to the windscreen, behind the rear-view mirror. – – – – – – This function is a driving aid in the event of the accidental crossing of a continuous or broken line in the road. However, the function is not intended to replace the driver.
Lane departure warning system (2/2) When a line is crossed and the indicators have not been activated, the function alerts the driver through warning light on the instrument panel, and a beep. Conditions for non-activation of alerts 1 Activation Press button 1: the warning light on the 1 button lights up, accompanied by the message “Lane deviation warning on” and a beep.
Cruise control/speed limiter: speed limiter function (1/3) The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. 1 2 A 4 3 5 Controls 1 Limit speed activation, storage and increase switch (+). 2 Decrease limit speed (-). 3 Switch the function to standby, with limit speed memorised (O). 4 Activation and recall of memorised limit speed (R). 5 Main “On/Off” switch. Switching on Press switch 5 on the side showing .
Cruise control/speed limiter: speed limiter function (2/3) Driving Exceeding the limit speed When a limited speed has been stored and this speed is not reached, driving is similar to driving a vehicle without the speed limiter function. It is possible to exceed the limit speed at any moment. To do this: press the accelerator pedal firmly and fully (beyond the kickdown point).
Cruise control/speed limiter: speed limiter function (3/3) Switching off the function 1 2 4 3 A The speed limiter function is deactivated if you press switch 5: in this case a speed is no longer stored. The orange indicator light on instrument panel A goes out to confirm that the function is deactivated. 5 Putting the function on standby The speed limiter function is suspended when you press switch 3 (O).
Cruise control/speed limiter: cruise control function (1/4) The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 20 mph (30 km/h). 1 2 4 3 5 Controls 1 Limit speed activation, storage and increase switch (+). 2 Decrease cruising speed (-). 3 Switch the function to standby (with memorisation of governed cruising speed) (O).
Cruise control/speed limiter: cruise control function (2/4) Driving 1 2 4 3 A Once a cruising speed is stored and the cruise control function is active, you may lift your foot off the accelerator pedal. 5 Switching on Press switch 5 on the side showing . The warning light comes on, lit green, and the message “Cruise control” appears on instrument panel A, accompanied by dashes to indicate that the cruise control function is activated and waiting to store a cruising speed.
Cruise control/speed limiter: cruise control function (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelerator pedal. 1 2 4 3 5 Adjusting the cruising speed The cruising speed may be changed by pressing the following repeatedly: – switch 1 (+) to increase the speed, – switch 2 (-) to decrease the speed. The cruise control function is in no way linked to the braking system. 2.
Cruise control/speed limiter: cruise control function (4/4) Switching off the function 1 2 4 3 A The cruise control function is deactivated if you press switch 5: in this case a speed is no longer stored. The green indicator light on the instrument panel A goes out to confirm that the function is deactivated. 5 Returning to the cruising speed If a speed is stored, it can be recalled, once you are sure that the road conditions are suitable (traffic, road surface, weather conditions, etc.).
PARKING DISTANCE CONTROL (1/4) Operating principle Ultrasonic detectors, installed in the front or rear bumper depending on the vehicle, measure the distance between the vehicle and an obstacle whilst reversing. 1 This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 30 centimetres from the obstacle. Note: display 1 shows the vehicle surroundings using beeps.
PARKING DISTANCE CONTROL (2/4) Front parking distance control (depending on vehicle) 1 Operation The parking distance control system is only activated when the vehicle is driven at a speed below approximately 6 mph (10 km/h). Most objects located less than approximately 60 centimetres away from the front of the vehicle are detected and a beep is emitted. Depending on the vehicle, the red zone of the display 1 lights up - see the following page.
PARKING DISTANCE CONTROL (3/4) Deactivating the system 2 You may permanently activate or deactivate the front or rear parking distance control separately. A 3 Parking in forwards gear When the vehicle moves from a speed greater than 6 mph (10 km/h) to a speed of less than 6 mph (10 km/h), the red zone on the display 2 and the message “Warning : obstacle” appears on the instrument panel A to signal the presence of an object less than 60 centimetres in front of the vehicle.
PARKING DISTANCE CONTROL (4/4) Operating faults When the system detects an operating fault , a beep sounds for approximately 3 seconds each time reverse gear is selected and is accompanied by the message “Check parking sensor” shown on the instrument panel A. Please consult an authorised dealer. Special features Ensure that the ultrasonic sensors are not obscured (by dirt, mud, snow, etc.).
Reversing camera 1 2 C B A Fixed clearance gauge 2 The fixed clearance gauge comprises coloured markers A, B and C indicating the distance behind the vehicle: – A (red) approximately 50 centimetres from the vehicle; – B (yellow) approximately 1 metre from the vehicle; – C (green) approximately 2 to 3 metres from the vehicle; This gauge remains fixed and indicates the vehicle trajectory if the wheels are in line with the vehicle.
Automatic gearbox (1/3) Driving in automatic mode 4 1 3 2 5 9 6 8 7 Selector lever 1 Operation Display 3 on the instrument panel shows the mode and gear selected. With the gear lever 1 in position P, switch on the ignition. 4: P: park 5: R: reverse gear 6: N: neutral 7: D: automatic mode 8: manual mode 9: zone displaying gearbox mode or gear engaged in manual mode To move out of position P, you must depress the brake pedal before pressing unlocking button 2.
Automatic gearbox (2/3) Driving in manual mode Special circumstances Parking the vehicle With the selector lever in position D, move the lever to the left. Shifting the lever repeatedly allows you to change gears manually: – If the road contours and bends do not allow you to stay in automatic mode (e.g.: in the mountains), we recommend that you change to manual mode. This will prevent the automatic gearbox from changing gears repeatedly when climbing, and permit engine braking on long descents.
Automatic gearbox (3/3) Operating faults – When driving, if the message “Check auto gearbox” appears on the instrument panel, this indicates there is a fault. Contact your approved Dealer as soon as possible. A 2 3 – When driving, if the message “Auto gearbox overheating” appears on the instrument panel, stop the vehicle to allow the gearbox to cool down. Contact your approved Dealer as soon as possible.
2.
Section 3: Your comfort Air vents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual air conditioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic climate control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air conditioning: information and advice on use.. . .
AIR VENTS: air outlets (1/2) 1 2 3 4 5 6 7 7 9 8 8 1 side air vent 2 side window demister outlet 3 windscreen demister outlets 4 centre air vents 5 side window demister outlet 6 side air vent 3.2 8 7 rear air vents 8 passenger footwell heater outlets 9 automatic climate control/manual air conditioning control panel.
AIR VENTS: air outlets (2/2) 1 3 2 4 1 2 Front seats Air flow Turn control knob 1 (beyond the point of resistance): To remove bad odours from your vehicles, only use the systems designed for this purpose. Consult an approved Dealer. Rear seats Move tab 3 to the right or left to direct the air flow. Turn control knob 4: – downwards to decrease the air flow and direct it downwards; Up: maximum air flow. Down: closed. – upwards to increase the air flow and direct it upwards.
Manual air conditioning (1/2) 2 1 3 4 Distribution of air in the passenger compartment There are five air distribution options. Turn control 4 to choose the distribution option. W i The air flow is directed to the windscreen and the front side window demisting vents. The air flow is distributed between all the air vents, the front side window demisting vents, the windscreen demisting vents and the footwells. The controls 6 1 Adjusting the air temperature.
Manual air conditioning (2/2) 1 2 3 4 Adjusting the ventilation speed Turn control 2 clockwise to increase the air flow in the passenger compartment. Passenger compartment ventilation is referred to as “blown air”. The ventilation fan determines the air flow. However, it is also affected by the vehicle speed. Switching the air recirculation on “OFF" position: The system is deactivated: the ventilation speed is zero (vehicle stationary).
automatic climate control (1/5) 2 1 3 6 13 11 10 1 and 6 Air temperature. 2, 3 and 4 Automatic programmes. 5 Distribution of air in the passenger compartment. 7 Off button. 8 Air conditioning. Automatic mode 5 12 The controls 3.6 4 9 8 7 9 De-icing/demisting of the rear screen and, depending on the vehicle, the door mirrors. 10 “Clear View” function. 11 Air recirculation. 12 Ventilation speed. 13 Display.
automatic climate control (2/5) 2 1 3 Clear View function 4 12 Press button 10: the integrated indicator light comes on. 6 This function quickly demists and deices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-icing functions must be activated. Press button 9 to stop the heated rear screen operating; the integrated indicator goes out.
automatic climate control (3/5) 3 The displayed temperature values show a comfort level. Switching air conditioning on or off In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions. Press switch 8 to switch off the air conditioning; the integrated indicator comes on and “AC OFF” is shown on the display 13. 13 8 When starting the engine, increasing or decreasing the value displayed will not allow the comfort level to be reached any more quickly.
automatic climate control (4/5) 5 W × The air flow is directed to the windscreen and the front side window demisting vents. The air flow is distributed between all the air vents, the front side window demisting vents, the windscreen demisting vents and the footwells. 12 ¿ ¾ ½ The air flow is directed mainly towards the footwells. The air flow is directed towards the dashboard vents and the footwells. Rear screen de-icing/ demisting 13 B Press button 9: the integrated indicator light comes on.
automatic climate control (5/5) Recycling 2 This function is managed automatically (operation is confirmed by warning light 14 on display 13), but you can also activate it manually. Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle; – air recirculation allows the external atmosphere to be cut off (when driving in polluted areas, etc.); – lowering the passenger compartment temperature as quickly as possible.
Air conditioning: information and advice on use Advice on use In some situations, (air conditioning off, air recirculation activated, ventilation speed at zero or low, etc.) you may notice that condensation starts to form on the windows and windscreen. If there is condensation, use the “Clear View” function to remove it, then use the air conditioning in automatic mode to stop it forming again. If the condensation does not clear, use the FAST programme. Note Presence of water under the vehicle.
Electric windows/Electric sunroof (1/3) These systems operate with the ignition on or off, until one of the front doors is opened (limited to about 3 minutes). Safety of rear occupants The driver can disable operation of the electric windows and, depending on the vehicle, the rear doors, by pressing switch 4. The indicator light integrated in the switch lights up to confirm that the locks have been activated.
Electric windows/Electric sunroof (2/3) Special note 0 A B C D 8 9 Your vehicle is equipped with an antipinch facility: when the sunroof encounters resistance whilst closing, (somebody’s fingers, etc.) it stops and then moves back several centimetres.
Electric windows/Electric sunroof (3/3) Remote control window closing (vehicles with 4 one-touch electric windows). When you lock the doors from the outside, press the locking button on the RENAULT card twice in quick succession, or on the driver's door in hands-free mode, and all the windows will close automatically. It is recommended that the user only operates the system when the vehicle can be seen clearly and no one is inside. Note: locking the doors using the RENAULT card deactivates hands-free mode.
MANUAL WINDOW WINDERS/Interior lighting (1/2) 1 2 3 4 5 Manual window winders Courtesy light Front door lights Turn handle 1. Tilt switch 3 to move it to the position for: On equipped vehicles, light 5 comes on when the door is opened. – permanent lighting; – intermittent lighting, which comes on when a door is opened. This switches off after a time delay, once the doors concerned have been closed correctly; – immediate switching off.
Interior lighting (2/2) 7 6 7 Glove box light 6 Luggage compartment light 7 Light 6 comes on when the cover is opened. Depending on the vehicle, light 7 comes on when the luggage compartment is opened. 3.
SUN BLIND/mirrors 2 1 4 3 Front sun visor Vanity mirror Child minder mirror Lower the sun visor 1 over the windscreen or unclip it and lower it over the side window. Slide cover 3. Pull on recess 4 to open it. Depending on the vehicle, light 2 is automatic. 3.
SUN VISOR 5 2 1 3 4 6 Lateral sun visor Rear side sun blind Rear sun blind on the tailgate Pull the sun blind upwards using tab 1 until hook 2 engages in its housing (make sure that the hook is correctly clipped in). Pull the sun blind upwards using hook 3 until it engages in housing 4 (make sure that the hook is correctly clipped in). Pull the sun blind upwards using tabs 6 until they engage in hook 5 (make sure they are correctly clipped in). 3.
Passenger compartment storage/fittings (1/6) 3 2 1 Door pockets 1 It can hold a 1.5 litre bottle. Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use.
Passenger compartment storage/fittings (2/6) 4 5 6 Sunglasses holder 4 Sun blind storage 5 This can be used for storing motorway tickets, cards, etc. 3.20 Central storage compartment or control 6 Depending on the vehicle, central control 6 may be replaced by a storage compartment.
Passenger compartment storage/fittings (3/6) 10 8 A 7 C D B 9 Central elbow rest 8 The central elbow rest slides to allow the length to be adjusted. Slide it (movement A). Centre console 9 Centre console storage compartment C Armrest storage compartment D Lift up the armrest 8. With the armrest in the retracted position, press button 10 and lift armrest 8. The compartment can hold a 1.5 litre bottle. The centre console slides to allow the length to be adjusted.
Passenger compartment storage/fittings (4/6) 10 Passenger storage compartment 11 11 Cup holder 11 It can hold a can, a cup or the ashtray. Pull handle 10 to open it. The glove box can hold A4-size documents, a large bottle of water, etc. The storage compartment is ventilated and refrigerated. When turning corners, accelerating or braking, ensure that the receptacle being held by the cup holder is not dislodged. There is a risk of burning if hot liquid escapes. 3.
Passenger compartment storage/fittings (5/6) 13 14 15 12 13 Rear door storage compartment 12 Front seat storage compartments 13 Clothes hooks 14 Grab handle 15 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle. Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passengers during sudden turning or braking. 3.
Passenger compartment storage/fittings (6/6) 17 18 16 Retaining hook 16 This is used to hold bags while the vehicle is moving. Note: do not exceed a load of 9 kg. Storage drawer 17 under front and rear seats Front and rear underfloor storage 18 These drawers can hold a road atlas, the vehicle documentation, etc. These compartments can hold road maps, manuals, cloths, etc. Special feature of rear storage areas The storage area covers may be removed: once open, pull up.
Ashtray/cigar lighter/accessories socket 1 3 3 2 Cigar lighter 1 Accessories sockets With the ignition on, push in cigar lighter 1; it will spring back with a click when it is ready. Pull it out to use. After use, replace it without pushing it all the way in. You may use cigar lighter recess 1 or one of the sockets 3 (depending on the vehicle). They are designed for connecting accessories with a maximum power rating of 120 Watts (voltage: 12V) which have been approved by our Technical Department.
Rear headrests A B 1 Position for use To adjust side supports A Lift the headrest to maximum height, then lower it until it locks. Depending on the vehicle, sections A can be adjusted independently to the desired position. To remove the headrest Press the tab(s) 1, then remove the headrest. To refit the headrest Insert the rods into the holes, press tab 1 and lower the headrest. 3.26 Storage position B Press tab 1 and lower the headrest completely.
ADJUSTING THE REAR SEATS 3 1 To fold down a seatback (table position) 3 4 Lower headrest 3. 1 4 Lift handle 4 or, depending on the vehicle, pull tab 1. An occasional table position can be created by folding the seatback all the way down onto the seat cushion. The seats can hold up to 80 kg in this position. 2 The rear seats are separate seats. To tilt the seatback To move the seats forwards or backwards Lift handle 4 or pull strap 1 and tilt the seatback to the desired position.
REAR SEAT FUNCTIONS (1/2) 1 3 1 2 Folding up a seat Lower the headrest. Seat with control 2 Lift the control 2, the seatback is lowered and lift the seat as far forwards as possible. Seat without control 2 A 4 Note: it may be necessary to move the passenger and/or driver’s seats forwards and to lower the seatback in order to tilt the seat as far forwards as possible. The seats can be folded down from the rear of the vehicle on 7-seater vehicles.
REAR SEAT FUNCTIONS (2/2) When fitting side seats, make sure that the seat belt buckle is inside the vehicle. B 8 6 7 6 9 To remove a seat With the seat folded down, gently lower it while lifting handle 6. Release the handle and guide the seat to the floor. Remove the seat from the vehicle by lifting it. To fit a seat Attach the hooks 8 to rail 7 marked 9 by gently lifting the back of the seat. Tilt the seat as far forward as possible, movement B (handle 6 locks in place).
REAR SEAT OPERATION: 7-seater version (1/2) 1 1 A A A A 2 Third row rear seats Folding up a seat – From the luggage compartment, lower the headrest; – pull strap 2; – push the seatback (areas A) to lock the seat, ensuring that it is correctly locked. Note: the hooks 1 secure the seat belt buckles. 3.
REAR SEAT OPERATION: 7-seater version (2/2) 3 Accessing the third row rear seats – Via the rear doors, push the second row seat forwards; – lower the seat headrest; – lift handle 3; the seatback lowers itself. Fold the seat down; – pull the second row rear seat to put it into the table position; – lift the seatback. Use restriction It is not permitted to drive with a second row rear seatback or seat folded down when there is a passenger occupying a third row rear seat.
Tailgate 2 1 To open Press button 1 and lift the tailgate. To close Lower the tailgate using the handles 2 inside the tailgate to help you. 3 Opening the doors manually from the inside Special note If it is impossible to unlock the tailgate, it can be done manually from inside: – access the luggage compartment by tilting the rear bench seatback(s), – insert a pencil or similar object in recess 3 and slide the unit as shown in the illustration; – push the tailgate to open it. 3.
REAR PARCEL SHELF: normal chassis versions 1 B A Rear parcel shelf To remove, unhook the two straps 1. Fold section A onto section B, then pull up and towards you. To refit it, proceed in reverse order to removal. Maximum load on the rear parcel shelf: 25 kg evenly distributed. Do not place any objects, especially heavy or hard objects, on the parcel shelf. These may pose a risk to the vehicle occupants if the driver has to brake suddenly or if the vehicle is involved in an accident. 3.
LUGGAGE COVER: long chassis versions 1 B A 2 To remove the flexible section of the luggage cover Using handle 1, pull it gently to release the pins from their mounting points located on each side of the luggage compartment. Guide the luggage cover onto the roller. Removing the luggage cover Push the luggage cover to the right (movement A) and lift the left-hand side of the inertia reel (movement B).
Luggage compartment storage space and fittings (1/2) 2 1 Side storage compartments 1 Depending on the vehicle, this may be used to hold oil containers etc. Bag hooks 2 Maximum weight per hook: 5 kg. 3 Storage compartment under luggage compartment carpet Depending on the vehicle, to access this, lift the luggage compartment carpet. Partition 3 can be removed. 3.
Luggage compartment storage space and fittings (2/2) 4 5 6 Separating the luggage compartment (depending on the vehicle) The loading area can be separated. Lift divider 4. The elastic band 5 on the back is used to hold objects vertically. Maximum weight: 30 kg, evenly distributed. Always place objects being transported so that the heaviest items are resting against the back of the rear bench seat. 3.
Transporting objects in the luggage compartment/towing (towing equipment) A Always place the objects to be transported so that their largest side rests against the back of the rear bench seat, for normal loads (example A) or against the back of the front seats B when the rear bench seatbacks are folded down. If you have to place objects on the folded seat back, it is vital that you remove the headrests before folding the seat back so that it can be folded as flat as possible against the seat.
LUGGAGE NET (1/2) A 1 B 2 4 5 3 Depending on the vehicle, this may be used when transporting animals or luggage to isolate them from the passenger section. It can be positioned: – behind the rear seats A; – behind the front seats B. The luggage net is designed to retain a maximum weight of 10 kg. Risk of injury. 3.
LUGGAGE NET (2/2) 6 7 6 10 11 9 8 Fitting the luggage net behind the rear seats – attach net strap hook 8 to the lower ring; Inside the vehicle on each side: – adjust the position of the second row seats: ensure that the seatbacks do not touch the luggage net. (behind the second row rear seats on the 7-seater version) – push the second row seats fully forward; – lift cover 6 to access the luggage net upper mounting rail; – adjust net strap 9 so that it is taut.
ROOF BARS 1 1 Access to the mounting points Open the doors to access the mounting points 1. If original roof bars, approved by our Technical Department, are supplied with screws, only use these screws for attaching the roof bars to the vehicle. 3.40 For information on the range of equipment adapted to your vehicle, we advise you to consult an approved Dealer. Refer to the fitting instructions for information on how to fit roof bars and conditions of use.
multimedia equipment 1 2 6 4 5 3 Multimedia systems A The equipment described below may or may not be fitted to the vehicle, and its location may vary, depending on the vehicle navigation system version.
3.
Section 4: Maintenance Bonnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level/Engine oil change. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Levels:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . engine coolant. . . . . . . . . . . . . . . . .
Bonnet 2 Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and guide it down, allowing a 30 cm gap before it is closed, then release it. It will latch automatically under its own weight. 1 To open, pull handle 1, located on the left-hand side of the dashboard. Unlocking the bonnet catch To release it, lift tab 2. The engine may be hot when carrying out operations in close proximity.
ENGINE OIL LEVEL: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level between oil changes. B A However, contact your approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period. Oil change frequency: check the oil level from time to time and certainly before any long journey to avoid the risk of damaging your engine.
ENGINE OIL LEVEL: topping up, filling (1/3) 1 2 1 1 2 2 Topping up/Filling The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day). Engine oil grade Refer to the Maintenance Service Booklet for your vehicle. Do not exceed the max level and do not forget to refit cap 1 and dipstick 2. 4.
ENGINE OIL LEVEL: topping up, filling (2/3) 1 1 2 2 1 1 2 2 4.
ENGINE OIL LEVEL: topping up, filling (3/3)/Oil change Oil change Service interval: refer to the Maintenance Service Booklet for your vehicle. Average capacities for oil change including oil filter (for information) 1.6 16V engine: 5.0 litres 2.0 16V engine: 4.4 litres 1.4 TCe engine: 4.5 litres 1.5 dCi engine : 4.5 litres 1.6 dCi engine: 5.5 litres 1.9 dCi engine: 5.1 litres 2.0 dCi engine: 7.
LEVELS (1/3) 1 Checking intervals Replacement intervals Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). Refer to the Maintenance Service Booklet for your vehicle. If the level needs to be topped up, only use products approved by our Technical Department which ensure: – protection against freezing; – anticorrosion protection of the cooling system.
LEVELS (2/3) 2 Level 2 Topping up It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI” warning line. After any operation on the hydraulic circuit, a specialist must replace the fluid. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking procedure from our network or from the manufacturer’s website.
LEVELS (3/3)FILTERS Liquid 3 Windscreen washer fluid. In winter, use anti-freeze product. Jets Use a tool such as a needle to adjust the height of the windscreen washer jets. Filters The replacement of filter elements (air filter, passenger compartment filter, diesel filter, etc.) is scheduled in the maintenance operations for your vehicle. Replacement intervals for filter elements: refer to the Maintenance Service Booklet for your vehicle.
Tyre pressure A B A C D C D G H E E E E E F F F F F I The tyre pressure is indicated on label A affixed to the edge of the driver’s door. Open the door to read it. G: recommended pressure for optimising fuel consumption. B: dimension of the tyres fitted to the vehicle. H: emergency spare wheel dimensions. C: vehicle load. D: intended driving speed. Note: driving comfort may be altered. I: tyre pressure for the emergency spare wheel.
Battery (1/2) 1 Depending on the vehicle, a system continuously checks the battery charge status. If this drops, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine. Then the message “Battery charging” appears on the instrument panel for the duration of the charging time.
Battery (2/2) 8 9 Replacing the battery As this operation is complex, we advise you to contact an approved Dealer. After changing or disconnecting the battery, the message “New battery?” will appear on the instrument panel. Select “Yes” or “No” with a short press on one of the buttons 8 or 9, then confirm with a long press on one of the two buttons. dealer. 4.12 The battery is a specific type, please ensure it is replaced with the same type.
Bodywork maintenance (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the exterior of the vehicle regularly. Protection against the effects of corrosive agents Although your vehicle has been treated with very effective anti-corrosion products, it nevertheless remains subject to the effects of different parameters.
Bodywork maintenance (2/2) You should Observe the vehicle stopping distances when driving on gravelled surfaces to prevent paint damage. Repair, or have repaired quickly, areas where the paint has been damaged, to prevent corrosion spreading. Remember to visit the body shop periodically in order to maintain your anti-corrosion warranty. Refer to the Maintenance Service Booklet. Respect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway).
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the interior of the vehicle regularly. A stain should always be dealt with swiftly. Whatever type of stain is on the trim, use cold (or warm) soapy water with natural soap. Detergents (washing-up liquid, powdered products, alcohol-based products) should not be used. Use a soft cloth. Rinse and soak up the excess. Glass instrument panel (e.g.
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable equipment originally fitted in the vehicle If you need to remove equipment in order to clean the passenger compartment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driver’s mat should be fitted on the driver’s side, etc.) and fit them with the components supplied with the equipment (for example, the driver mat should always be fixed using the pre-fitted mounting components).
Section 5: Practical advice Puncture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tool kit (jack, wheelbrace, etc.). . . . . .
Puncture/EMERGENCY SPARE WHEEL (1/2) In case of puncture Depending on the vehicle, a tyre inflation kit or emergency spare wheel is provided (refer to the following pages). Special note The Tyre Pressure Monitor function does not check the emergency spare wheel (the wheel replaced by the emergency spare wheel disappears from the instrument panel display). Refer to the information on the “Tyre pressure monitor” in Section 2.
Puncture/EMERGENCY SPARE WHEEL (2/2) 4 B 5 3 Emergency spare wheel B It is located under the vehicle. In the luggage compartment, lift cover 3 and remove the blanking cover. Only use the wheel brace 4 (using a different tool could damage the mechanism) to unroll the retaining cable, making sure it remains taut, and the wheel falls to the ground. From outside the vehicle, stand the wheel up, press lock 5 and rotate it quarter of a turn. Remove the cable from the rim to release it.
TYRE PRESSURE KIT (1/3) B A Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE PRESSURE KIT (2/3) 1 2 – press switch 5 to inflate the tyre to the recommended pressure (check the label affixed to the edge of the driver’s door); 3 4 – after a maximum of 5 minutes, stop inflating and read the pressure (on pressure gauge 4); 5 C 6 D 8 Depending on the vehicle, in the event of a puncture, use the kit located in storage compartment C or underneath luggage compartment carpet D.
TYRE PRESSURE KIT (3/3) – affix the driving recommendation label 9 to the dashboard where it can easily be seen by the driver; – store the kit; 9 8 Once the tyre is inflated correctly: – stop using the kit; – close the integrated cap on the bottle again; – disconnect the adapter 8; – at the end of this initial inflation operation, air will still escape from the tyre; you must drive a short distance in order to seal the hole; – start immediately and drive at between 12 and 40 mph (20 and 60 km/h) in order
TOOLS (1/2) Hubcap tool 4 2 This tool is used to remove the wheel trims. 1 Bolt guide 5 For tightening/loosening wheel bolts on vehicles fitted with alloy wheels 3 4 5 6 The presence of the tools depends on the vehicle. Wheelbrace 1 Allows the wheel bolts to be locked/unlocked. Jack 2 Fold it correctly before refitting it in its housing (ensure that wheelbrace 3 is correctly positioned). Towing hitch 6 Refer to the information on “Towing” in Section 5.
TOOLS (2/2)/wheel trim 7 9 D 10 B C A 8 12 7-seater version 5-seater version Wheel trim The tools are in compartment 8 of the luggage compartment: lift the third row rear right-hand seat, pull tab 7 then take out the jack and the bag containing the tools. To refit, reposition the bag containing the tools in its housing, fold the jack fully, wrap it in its soundproofing material and place it in its housing. Check that the assembly is correctly positioned (to avoid noise).
Changing a wheel (1/2) Vehicles equipped with a jack and wheelbrace 3 If necessary, remove the wheel trim. Use the wheelbrace 3 to slacken off the wheel bolts. Position it so as to be able to push from above. Offer up the jack 1 horizontally; the jack head must be lined up with the sill, closest to the wheel concerned, as shown by arrow 2. Start cranking the jack up by hand to align the base plate (which should be pushed slightly under the vehicle).
Changing a wheel (2/2) Undo the bolts and take off the wheel. Fit the emergency spare wheel onto the hub and rotate it until the mounting holes in the wheel coincide with those of the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel. Tighten the bolts, checking that the wheel is correctly positioned on its hub and unscrew the jack.
Tyres (1/3) Tyre and wheel safety The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. 2 You must make sure that your tyres conform to local road traffic regulations. 1 When the tread has worn down to the wear warning strips, these strips will become visible 2: it is then necessary to replace your tyres because the tread rubber is now only 1.6 mm deep at most, resulting in poor road holding on wet roads.
Tyres (2/3) Tyre pressures Adhere to the tyre pressures (including the emergency spare wheel). The tyre pressures should be checked at least once a month and additionally before any long journey (refer to the label affixed to the edge of the driver’s door). Pressures should be checked when the tyres are cold; ignore higher pressures which may be reached in hot weather or following a fast journey. If tyre pressures cannot be checked when the tyres are cold, the normal pressures must be increased by 0.
Tyres (3/3) Use in winter Chains For safety reasons, fitting snow chains to the rear axle is strictly forbidden. Chains cannot be fitted to tyres which are larger than those originally fitted to the vehicle. Studded tyres This type of equipment may only be used for a limited period and as laid down by local legislation. It is necessary to observe the speed specified by current legislation. These tyres must, at a minimum, be fitted to the two front wheels.
Front headlights: changing bulbs (1/3) Daytime running light 1 2 A B The bulbs detailed below can be replaced. However, we recommend that these be replaced by an approved Dealer if this proves difficult. (depending on the vehicle) Remove cover B, turn bulb holder 3 to release it then replace the bulb. Daytime running light bulb type: P21LL. Discharge bulb main beam headlights/dipped beam headlights 3 Never open cover A Bulb type: D1S.
Front headlights: changing bulbs (2/3) 4 5 6 A C B Main beamA/dipped B halogen headlights Removal Remove the cover A or B, unclip the bulb raising the connector 4 or 5 (movement C or D), then replace the bulb. Bulb type: H7. Access to the dipped beam headlight on the battery side Depending on the vehicle, push cable 6, taking care not to detach clip 7 or deform terminal 8. D 7 8 Refitting Carry out the operations in reverse order.
Front headlights: changing bulbs (3/3) 9 10 Front fog lights 9 The front bumper needs to be removed; consult an approved Dealer. Daytime running lights 10 Please see an authorised dealer. The bulbs are under pressure and can break when replaced. Risk of injury. 5.16 Any operation on (or modification to) the electrical system must be performed by an approved dealer since an incorrect connection might damage the electrical equipment (harness, components and in particular the alternator).
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (1/4) 1 Long chassis version Direction indicator lights/brake and side lights From the luggage compartment, remove the cover and unscrew end piece 1. 2 From the outside, undo screw 2 using a flat-blade screwdriver or similar and pull the light unit towards you. Unclip the bulb holder a quarter of a turn. 3 4 LED lighting The lights are equipped with an LED lighting system as soon as the side lights are switched on. Replace the bulb.
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (2/4) 7 5 6 9 Normal chassis version Direction indicator lights and brake lights From the outside, undo screw 5 using a flat-blade screwdriver or similar and pull the light unit towards you. Unclip the bulb holder by pressing on the tabs 6. Refitting Replace the bulb. To refit, proceed in the reverse order, taking care not to damage the wiring. Direction indicator light 7 Note: do not remove seal 9. Bulb type: PY21W.
REAR LIGHTS AND INDICATOR LIGHTS: changing bulbs (3/4) 11 10 Side light From the luggage compartment, unclip the cover. Using a tool, unscrew nut 10. 12 From the outside of the vehicle, pull on the light unit to remove it then unscrew bulb holder 11 a quarter of a turn. Rear fog light and reversing light Replace the bulb. Access bulb holder 12 via the underneath of the vehicle, then unscrew it by turning towards the centre of the vehicle. Bulb type: W5W.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (4/4) 13 A 14 16 15 High level brake light 13 Number plate lights 14 Indicator lights 16 Consult an approved Dealer. Unclip light 14 by pressing tab 15. Unclip indicator light 16 using a flatblade screwdriver or similar. Position it to A to tilt the rear indicator light towards the front of the vehicle. Remove the light cover to gain access to the bulb. Bulb type: C5W festoon bulb. Turn the bulb holder a quarter of a turn and take out the bulb.
INTERIOR LIGHTING: changing bulbs (1/2) 1 A B 2 3 Courtesy light Door lights Sliding central console light – Set the three switches to the central position; Unclip light 2 (using a flat-blade screwdriver or similar). Unclip bulb 3 from its support. – move the courtesy light backwards (movement A) then tilt the front downwards (movement B); Turn the bulb holder a quarter of a turn and take out the bulb.
INTERIOR LIGHTING: changing bulbs (2/2) 5 6 7 4 Luggage compartment lights Unclip lights 4 using a flat-blade screwdriver or similar. Disconnect the light. Press tab 5 to release lens 7 and access bulb 6. Bulb type: W5W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
FUSES (1/2) 1 B A Fuse box Tweezers 1 If any electrical component does not work, check the condition of the fuses. Remove the fuse using tweezers 1, located at the back of flap A or B. Unclip cover A or B (depending on vehicle). In accordance with local legislation or as a precautionary measure: Check the fuse in question and replace it, if necessary, by a fuse of the same rating. To remove the fuse from the tweezers, slide the fuse to the side. It is not advisable to use the free fuse locations.
FUSES (2/2) 3 7 10 14 4 8 11 15 1 5 9 12 16 2 6 13 17 C 18 19 Allocation of fuses (the presence of certain fuses depends on the vehicle equipment level) 1 Electronic parking brake; 2 Brake lights; 3 Automatic door locking; 4 Driver’s window winder; 5 Instrument panel; 6 Direction indicator lights; 7 Navigation system; 8 Interior rear-view mirror; 9 Rear screen wiper; 10 and 11 Rear electric windows; 12 ABS/ESP; 13 Passenger electric window; 14 Windscreen washer; 15 Heated door mirrors;
Battery: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (courtesy lights, etc.) are switched off before disconnecting or reconnecting the battery; The battery charger must be compatible with a battery with nominal voltage of 12 volts. – when charging, stop the charger before connecting or disconnecting the battery; Do not disconnect the battery when the engine is running.
Battery: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle 2 If you have to use the battery from another vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you already have jump leads, ensure that they are in perfect condition. The two batteries must have an identical nominal voltage of 12 volts.
RENAULT card: battery 2 A B 4 1 Replacing the battery When the message “Low card battery” appears on the instrument panel, replace the RENAULTcard battery, press button 1, pulling on emergency key 2, then unclip cover 3 using tab 4. Remove the battery by pressing on one side (movement A) and by lifting the other (movement B) then replace it, ensuring the polarity and model, shown on cover 3 are respected.
Fitting a radio 1 2 2 3 3 If your vehicle is not fitted with an audio system, one can be fitted and locations have been provided for: – the radio 1; – tweeter speakers 2; – bass speakers 3. To install any equipment, please consult an approved dealer. Radio location 1 Unclip the blanking cover. The aerial, + and – supply and speaker wire connections are located behind it. 5.28 – In all cases, it is very important to follow the manufacturer’s instructions carefully.
ACCESSORIES Before fitting an electrical or electronic device (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle. If you are using an anti-theft device, only attach it to the brake pedal. Contact an approved dealer for this information. Electrical and electronic accessories – Connect accessories with a maximum power of 120 Watts only. Use of transmission/ receiving devices (telephones, CB equipment etc.
wiper blades: replacing 1 Check the condition of the wiper blades. You are responsible for their service life: 4 A B 5 2 3 C Windscreen wiper blades 1 With the ignition on and engine switched off, lower the windscreen wiper stalk completely: they stop slightly away from the bonnet. Lift wiper arm 3, pull tab 2 (movement A) and push the blade upwards. Refitting Slide the blade along the arm until it clips on. Check that it is correctly locked. Return the windscreen wiper stalk to the park position.
Towing: breakdown (1/2) Before towing, unlock the steering column: with the clutch depressed, engage first gear (lever in position N or R for vehicles with automatic gearboxes), insert the RENAULT card in the card reader, then press the engine start button for two seconds. Reposition the lever to neutral (position N for vehicles fitted with an automatic gearbox). The column is unlocked, the accessory functions are supplied: the vehicle lights can be used (indicators, brake lights etc.).
Towing: breakdown (2/2) – Use a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed must be able to brake. 3 4 7 Only use the front 3 and rear towing points 5 (never use the driveshafts). These towing points may only be used for towing: never use them for lifting the vehicle directly or indirectly. 6 5 4 Access to towing points – A vehicle must not be towed if it is not fit to be driven.
Operating faults (1/5) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved Dealer as soon as possible. Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or unlock the doors. Card battery is flat. Replace the battery. You can still lock/ unlock and start your vehicle (refer to the information on “Locking/unlocking the doors” in Section 1 and “Starting/Stopping the engine” in Section 2).
Operating faults (2/5) The starter is activated POSSIBLE CAUSES WHAT TO DO The instrument panel indicator lights are weak or fail to light up and the starter does not turn. Battery terminals not tight, battery terminals disconnected or oxidised. Retighten or reconnect the terminals, or clean them if they are oxidised. Discharged battery or not operational. Connect another battery to the faulty battery.
Operating faults (3/5) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pressures, incorrectly balanced or damaged. Check the tyre pressures: if this is not the problem, have them checked by an approved Dealer. White smoke from the exhaust. This is not necessarily a fault. Smoke may be caused by regeneration of the particle filter. Refer to the information on “Special features of diesel versions” in Section 2. Smoke under the bonnet.
Operating faults (4/5) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine is overheating. The coolant temperature indicator is in the warning zone and warning light ® comes on. Engine cooling fan not working. Stop the vehicle, switch off the engine and contact an approved dealer. Coolant leaks. Check the coolant reservoir: it should contain fluid. If there is no coolant, consult an approved dealer as soon as possible.
Operating faults (5/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse, refer to the information on “Fuses”. The wiper does not stop. Faulty electrical controls. Consult an approved dealer. Direction indicators flashing more quickly. Blown bulb.
5.
Section 6: Technical specifications Vehicle identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine specifications. . . . . . . . . . . .
Vehicle identification plates A 6 7 8 9 10 1 2 3 4 5 The information shown on the vehicle identification plate should be quoted on all correspondence or orders. A B 6.2 Vehicle identification plate A 1 Vehicle type and chassis number. Depending on the vehicle, this information is also given on marking B. 2 Maximum permissible all-up weight. 3 Total train weight (vehicle fully loaded, with trailer). 4 Front axle Maximum permissible weight. 5 Rear axle Maximum permissible weight.
Engine identification plates (1/2) C 1 2 C 3 C The information on the engine plate (or label) C should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. C 6.
Engine identification plates (2/2) C 1 2 3 C C The information on the engine plate (or label) C should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. C 6.
Dimensions (in metres) (1/2) Normal chassis versions 0,888 2,702 0,753 1,546 4,343 1,624* 1,547 * Unladen 2,077 6.
Dimensions (in metres) (2/2) Long chassis versions 0,888 2,769 0,903 1,536 4,560 1,675* 1,539 * Unladen 6.
Engine specifications Versions 1.6 16V 1.4 Tce 2.0 16V 1.5 dCi 1.6 dCi 1.9 dCi 2.0 dCi Engine type (see engine plate) K4M H4J M4R K9K R9M F9Q M9R Cubic capacity (cc) 1.598 1.395 1.995 1.461 1 598 1.870 1.995 Type of fuel Octane Rating Spark plugs It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap.
WEIGHTS (in kg) The weights indicated are for a basic vehicle without options: they may vary depending on your vehicle’s equipment. Consult an approved Dealer.
Replacement parts and repairs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
service sheets (1/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (2/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (3/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (4/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (5/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (6/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
Anticorrosion check (1/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (2/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (3/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (4/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (5/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (6/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
6.
Alphabetical index (1/5) A ABS........................................................................2.23 → 2.26 accessories........................................................................ 5.29 accessories socket............................................................. 3.25 additional methods of restraint......................1.24 → 1.27, 1.30 side protection.............................................................. 1.29 to the rear seat belts.........................................1.
Alphabetical index (2/5) driving.........2.2 → 2.5, 2.9 → 2.17, 2.19 → 2.26, 2.29 → 2.39, 2.41 → 2.43 driving position settings......................................................................... 1.20 E electric beam height adjustment......................................... 1.83 electric windows.....................................................3.12 → 3.14 electronic parking brake.........................................2.12 → 2.14 Electronic Stability Program: ESP..........................2.23 → 2.
Alphabetical index (3/5) sounding the horn......................................................... 1.77 hubcap tool.................................................................. 5.7 – 5.8 I indicators.......................................................1.77, 5.14 → 5.16 indicators: direction indicators............................................... 1.77, 5.17 exterior temperature indicator....................................... 1.74 instrument panel...............................................1.
Alphabetical index (4/5) parking distance control.........................................2.36 → 2.39 power-assisted steering..................................................... 1.73 puncture...................................................5.2 – 5.3, 5.7 → 5.10 R radio................................................................................... 3.41 fitting a radio................................................................. 5.28 rear parcel shelf................................................
Alphabetical index (5/5) transporting children...........................1.31 – 1.32, 1.34 → 1.46 transporting objects in the luggage compartment......................................... 3.37 luggage net........................................................ 3.38 – 3.39 trims...................................................................................... 5.8 trip computer and warning system... 1.54 → 1.58, 1.63 → 1.71 tyre inflation kit...........................................................5.
( www.e-guide.renault.com ) RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
