Datasheet
Table Of Contents
- Cover
- Notes regarding these materials
- General Precautions on Handling of Product
- Configuration of This Manual
- Preface
- Contents
- Figures
- Tables
- Section 1 Overview
- Section 2 CPU
- Section 3 Exception Handling
- Section 4 Interrupt Controller
- 4.1 Features
- 4.2 Input/Output Pins
- 4.3 Register Descriptions
- 4.3.1 Interrupt Edge Select Register (IEGR)
- 4.3.2 Wakeup Edge Select Register (WEGR)
- 4.3.3 Interrupt Enable Register 1 (IENR1)
- 4.3.4 Interrupt Enable Register 2 (IENR2)
- 4.3.5 Interrupt Request Register 1 (IRR1)
- 4.3.6 Interrupt Request Register 2 (IRR2)
- 4.3.7 Wakeup Interrupt Request Register (IWPR)
- 4.3.8 Interrupt Priority Registers A to F (IPRA to IPRF)
- 4.3.9 Interrupt Mask Register (INTM)
- 4.4 Interrupt Sources
- 4.5 Interrupt Exception Handling Vector Table
- 4.6 Operation
- 4.7 Usage Notes
- Section 5 Clock Pulse Generator
- 5.1 Register Description
- 5.2 System Clock Generator
- 5.3 Subclock Generator
- 5.4 Prescalers
- 5.5 Usage Notes
- 5.5.1 Note on Resonators and Resonator Circuits
- 5.5.2 Notes on Board Design
- 5.5.3 Definition of Oscillation Stabilization Wait Time
- 5.5.4 Note on Subclock Stop State
- 5.5.5 Note on the Oscillation Stabilization of Resonators
- 5.5.6 Note on Using On-Chip Power-On Reset
- 5.5.7 Note on Using the On-Chip Emulator
- Section 6 Power-Down Modes
- 6.1 Register Descriptions
- 6.2 Mode Transitions and States of LSI
- 6.3 Direct Transition
- 6.3.1 Direct Transition from Active (High-Speed) Mode to Active (Medium-Speed) Mode
- 6.3.2 Direct Transition from Active (High-Speed) Mode to Subactive Mode
- 6.3.3 Direct Transition from Active (Medium-Speed) Mode to Active (High-Speed) Mode
- 6.3.4 Direct Transition from Active (Medium-Speed) Mode to Subactive Mode
- 6.3.5 Direct Transition from Subactive Mode to Active (High-Speed) Mode
- 6.3.6 Direct Transition from Subactive Mode to Active (Medium-Speed) Mode
- 6.3.7 Notes on External Input Signal Changes before/after Direct Transition
- 6.4 Module Standby Function
- 6.5 Usage Notes
- Section 7 ROM
- Section 8 RAM
- Section 9 I/O Ports
- Section 10 Realtime Clock (RTC)
- 10.1 Features
- 10.2 Input/Output Pin
- 10.3 Register Descriptions
- 10.3.1 Second Data Register/Free Running Counter Data Register (RSECDR)
- 10.3.2 Minute Data Register (RMINDR)
- 10.3.3 Hour Data Register (RHRDR)
- 10.3.4 Day-of-Week Data Register (RWKDR)
- 10.3.5 RTC Control Register 1 (RTCCR1)
- 10.3.6 RTC Control Register 2 (RTCCR2)
- 10.3.7 Clock Source Select Register (RTCCSR)
- 10.3.8 RTC Interrupt Flag Register (RTCFLG)
- 10.4 Operation
- 10.5 Interrupt Sources
- 10.6 Usage Notes
- Section 11 Timer C
- Section 12 Timer F
- Section 13 Timer G
- Section 14 16-Bit Timer Pulse Unit (TPU)
- 14.1 Features
- 14.2 Input/Output Pins
- 14.3 Register Descriptions
- 14.3.1 Timer Control Register (TCR)
- 14.3.2 Timer Mode Register (TMDR)
- 14.3.3 Timer I/O Control Register (TIOR)
- 14.3.4 Timer Interrupt Enable Register (TIER)
- 14.3.5 Timer Status Register (TSR)
- 14.3.6 Timer Counter (TCNT)
- 14.3.7 Timer General Register (TGR)
- 14.3.8 Timer Start Register (TSTR)
- 14.3.9 Timer Synchro Register (TSYR)
- 14.4 Interface to CPU
- 14.5 Operation
- 14.6 Interrupt Sources
- 14.7 Operation Timing
- 14.8 Usage Notes
- 14.8.1 Module Standby Function Setting
- 14.8.2 Input Clock Restrictions
- 14.8.3 Caution on Period Setting
- 14.8.4 Contention between TCNT Write and Clear Operation
- 14.8.5 Contention between TCNT Write and Increment Operation
- 14.8.6 Contention between TGR Write and Compare Match
- 14.8.7 Contention between TGR Read and Input Capture
- 14.8.8 Contention between TGR Write and Input Capture
- 14.8.9 Contention between Overflow and Counter Clearing
- 14.8.10 Contention between TCNT Write and Overflow
- 14.8.11 Multiplexing of I/O Pins
- 14.8.12 Interrupts when Module Standby Function is Used
- 14.8.13 Output Conditions for 0% Duty and 100% Duty
- Section 15 Asynchronous Event Counter (AEC)
- Section 16 Watchdog Timer
- Section 17 Serial Communications Interface 3 (SCI3, IrDA)
- 17.1 Features
- 17.2 Input/Output Pins
- 17.3 Register Descriptions
- 17.3.1 Receive Shift Register (RSR)
- 17.3.2 Receive Data Register (RDR)
- 17.3.3 Transmit Shift Register (TSR)
- 17.3.4 Transmit Data Register (TDR)
- 17.3.5 Serial Mode Register (SMR)
- 17.3.6 Serial Control Register (SCR)
- 17.3.7 Serial Status Register (SSR)
- 17.3.8 Bit Rate Register (BRR)
- 17.3.9 Serial Port Control Register (SPCR)
- 17.3.10 Serial Port Control Register 2 (SPCR2)
- 17.3.11 IrDA Control Register (IrCR)
- 17.3.12 Serial Extended Mode Register (SEMR)
- 17.4 Operation in Asynchronous Mode
- 17.5 Operation in Clock Synchronous Mode
- 17.6 Multiprocessor Communication Function
- 17.7 IrDA Operation
- 17.8 Interrupt Requests
- 17.9 Usage Notes
- 17.9.1 Break Detection and Processing
- 17.9.2 Mark State and Break Sending
- 17.9.3 Receive Error Flags and Transmit Operations (Clock Synchronous Mode Only)
- 17.9.4 Receive Data Sampling Timing and Reception Margin in Asynchronous Mode
- 17.9.5 Note on Switching SCK3 Pin Function
- 17.9.6 Relation between Writing to TDR and Bit TDRE
- 17.9.7 Relation between RDR Reading and bit RDRF
- 17.9.8 Transmit and Receive Operations when Making State Transition
- 17.9.9 Setting in Subactive or Subsleep Mode
- 17.9.10 Oscillator when Serial Communications Interface 3 is Used
- Section 18 Serial Communication Interface 4 (SCI4)
- Section 19 14-Bit PWM
- Section 20 A/D Converter
- Section 21 LCD Controller/Driver
- Section 22 I2C Bus Interface 2 (IIC2)
- 22.1 Features
- 22.2 Input/Output Pins
- 22.3 Register Descriptions
- 22.3.1 I2C Bus Control Register 1 (ICCR1)
- 22.3.2 I2C Bus Control Register 2 (ICCR2)
- 22.3.3 I2C Bus Mode Register (ICMR)
- 22.3.4 I2C Bus Interrupt Enable Register (ICIER)
- 22.3.5 I2C Bus Status Register (ICSR)
- 22.3.6 Slave Address Register (SAR)
- 22.3.7 I2C Bus Transmit Data Register (ICDRT)
- 22.3.8 I2C Bus Receive Data Register (ICDRR)
- 22.3.9 I2C Bus Shift Register (ICDRS)
- 22.4 Operation
- 22.5 Interrupt Request
- 22.6 Bit Synchronous Circuit
- 22.7 Usage Notes
- 22.7.1 Note on Issuing Stop Condition and Start (Re-Transmit) Condition
- 22.7.2 Note on Setting WAIT Bit in I2C Bus Mode Register (ICMR)
- 22.7.3 Restriction on Transfer Rate Setting in Multimaster Operation
- 22.7.4 Restriction on the Use of Bit Manipulation Instructions for MST and TRS Setting in Multimaster Operation
- 22.7.5 Usage Note on Master Receive Mode
- Section 23 Power-On Reset Circuit
- Section 24 Address Break
- Section 25 List of Registers
- Section 26 Electrical Characteristics
- Appendix
- Main Revisions and Additions in this Edition
- Index
- Colophon
- Address List
- Back Cover
Section 4 Interrupt Controller
Rev. 2.00 Jul. 04, 2007 Page 75 of 692
REJ09B0309-0200
Origin of
Interrupt Source
Name
Vector
Number
Vector Address IPR
Mask
Level
WDT WDT overflow (interval
timer)
27 H'00006C IPRB3, IPRB2 High
AEC AEC overflow 28 H'000070 IPRB1, IPRB0
TPU_1 TG1A (TG1A input
capture/compare match)
29 H'000074 IPRC7, IPRC6
TG1B (TG1B input
capture/compare match)
30 H'000078
TCI1V (overflow 1) 31 H'00007C
TPU_2 TG2A (TG2A input
capture/compare match)
32 H'000080 IPRC5, IPRC4
TG2B (TG2B input
capture/compare match)
33 H'000084
TCI2V (overflow 2) 34 H'000088
Timer F Timer FL compare match
Timer FL overflow
35 H'00008C IPRC3, IPRC2
Timer FH compare match
Timer FH overflow
36 H'000090
SCI4* Receive data full/transmit
data empty
Transmit end/receive error
37 H'000094 IPRC1, IPRC0
SCI3_1 Transmit
completion/transmit data
empty
Receive data full/overrun
error
Framing error/parity error
38 H'000098 IPRD7, IPRD6
SCI3_2 Transmit
completion/transmit data
empty
Receive data full/overrun
error
Framing error/parity error
39 H'00009C IPRD5, IPRD4
IIC2 Transmit data
empty/transmit end
Receive data full/stop
condition detection
NACK detection
Arbitration/overrun error
40 H'0000A0 IPRD3, IPRD2
10-bit A/D A/D conversion end 42 H'0000A8 IPRE7, IPRE6
(SLEEP instruction
execution)
Direct transition 43 H'0000AC IPRE5, IPRE4
Low