Datasheet
Table Of Contents
- Cover
- Notes regarding these materials
- General Precautions on Handling of Product
- Configuration of This Manual
- Preface
- Contents
- Figures
- Tables
- Section 1 Overview
- Section 2 CPU
- Section 3 Exception Handling
- Section 4 Interrupt Controller
- 4.1 Features
- 4.2 Input/Output Pins
- 4.3 Register Descriptions
- 4.3.1 Interrupt Edge Select Register (IEGR)
- 4.3.2 Wakeup Edge Select Register (WEGR)
- 4.3.3 Interrupt Enable Register 1 (IENR1)
- 4.3.4 Interrupt Enable Register 2 (IENR2)
- 4.3.5 Interrupt Request Register 1 (IRR1)
- 4.3.6 Interrupt Request Register 2 (IRR2)
- 4.3.7 Wakeup Interrupt Request Register (IWPR)
- 4.3.8 Interrupt Priority Registers A to F (IPRA to IPRF)
- 4.3.9 Interrupt Mask Register (INTM)
- 4.4 Interrupt Sources
- 4.5 Interrupt Exception Handling Vector Table
- 4.6 Operation
- 4.7 Usage Notes
- Section 5 Clock Pulse Generator
- 5.1 Register Description
- 5.2 System Clock Generator
- 5.3 Subclock Generator
- 5.4 Prescalers
- 5.5 Usage Notes
- 5.5.1 Note on Resonators and Resonator Circuits
- 5.5.2 Notes on Board Design
- 5.5.3 Definition of Oscillation Stabilization Wait Time
- 5.5.4 Note on Subclock Stop State
- 5.5.5 Note on the Oscillation Stabilization of Resonators
- 5.5.6 Note on Using On-Chip Power-On Reset
- 5.5.7 Note on Using the On-Chip Emulator
- Section 6 Power-Down Modes
- 6.1 Register Descriptions
- 6.2 Mode Transitions and States of LSI
- 6.3 Direct Transition
- 6.3.1 Direct Transition from Active (High-Speed) Mode to Active (Medium-Speed) Mode
- 6.3.2 Direct Transition from Active (High-Speed) Mode to Subactive Mode
- 6.3.3 Direct Transition from Active (Medium-Speed) Mode to Active (High-Speed) Mode
- 6.3.4 Direct Transition from Active (Medium-Speed) Mode to Subactive Mode
- 6.3.5 Direct Transition from Subactive Mode to Active (High-Speed) Mode
- 6.3.6 Direct Transition from Subactive Mode to Active (Medium-Speed) Mode
- 6.3.7 Notes on External Input Signal Changes before/after Direct Transition
- 6.4 Module Standby Function
- 6.5 Usage Notes
- Section 7 ROM
- Section 8 RAM
- Section 9 I/O Ports
- Section 10 Realtime Clock (RTC)
- 10.1 Features
- 10.2 Input/Output Pin
- 10.3 Register Descriptions
- 10.3.1 Second Data Register/Free Running Counter Data Register (RSECDR)
- 10.3.2 Minute Data Register (RMINDR)
- 10.3.3 Hour Data Register (RHRDR)
- 10.3.4 Day-of-Week Data Register (RWKDR)
- 10.3.5 RTC Control Register 1 (RTCCR1)
- 10.3.6 RTC Control Register 2 (RTCCR2)
- 10.3.7 Clock Source Select Register (RTCCSR)
- 10.3.8 RTC Interrupt Flag Register (RTCFLG)
- 10.4 Operation
- 10.5 Interrupt Sources
- 10.6 Usage Notes
- Section 11 Timer C
- Section 12 Timer F
- Section 13 Timer G
- Section 14 16-Bit Timer Pulse Unit (TPU)
- 14.1 Features
- 14.2 Input/Output Pins
- 14.3 Register Descriptions
- 14.3.1 Timer Control Register (TCR)
- 14.3.2 Timer Mode Register (TMDR)
- 14.3.3 Timer I/O Control Register (TIOR)
- 14.3.4 Timer Interrupt Enable Register (TIER)
- 14.3.5 Timer Status Register (TSR)
- 14.3.6 Timer Counter (TCNT)
- 14.3.7 Timer General Register (TGR)
- 14.3.8 Timer Start Register (TSTR)
- 14.3.9 Timer Synchro Register (TSYR)
- 14.4 Interface to CPU
- 14.5 Operation
- 14.6 Interrupt Sources
- 14.7 Operation Timing
- 14.8 Usage Notes
- 14.8.1 Module Standby Function Setting
- 14.8.2 Input Clock Restrictions
- 14.8.3 Caution on Period Setting
- 14.8.4 Contention between TCNT Write and Clear Operation
- 14.8.5 Contention between TCNT Write and Increment Operation
- 14.8.6 Contention between TGR Write and Compare Match
- 14.8.7 Contention between TGR Read and Input Capture
- 14.8.8 Contention between TGR Write and Input Capture
- 14.8.9 Contention between Overflow and Counter Clearing
- 14.8.10 Contention between TCNT Write and Overflow
- 14.8.11 Multiplexing of I/O Pins
- 14.8.12 Interrupts when Module Standby Function is Used
- 14.8.13 Output Conditions for 0% Duty and 100% Duty
- Section 15 Asynchronous Event Counter (AEC)
- Section 16 Watchdog Timer
- Section 17 Serial Communications Interface 3 (SCI3, IrDA)
- 17.1 Features
- 17.2 Input/Output Pins
- 17.3 Register Descriptions
- 17.3.1 Receive Shift Register (RSR)
- 17.3.2 Receive Data Register (RDR)
- 17.3.3 Transmit Shift Register (TSR)
- 17.3.4 Transmit Data Register (TDR)
- 17.3.5 Serial Mode Register (SMR)
- 17.3.6 Serial Control Register (SCR)
- 17.3.7 Serial Status Register (SSR)
- 17.3.8 Bit Rate Register (BRR)
- 17.3.9 Serial Port Control Register (SPCR)
- 17.3.10 Serial Port Control Register 2 (SPCR2)
- 17.3.11 IrDA Control Register (IrCR)
- 17.3.12 Serial Extended Mode Register (SEMR)
- 17.4 Operation in Asynchronous Mode
- 17.5 Operation in Clock Synchronous Mode
- 17.6 Multiprocessor Communication Function
- 17.7 IrDA Operation
- 17.8 Interrupt Requests
- 17.9 Usage Notes
- 17.9.1 Break Detection and Processing
- 17.9.2 Mark State and Break Sending
- 17.9.3 Receive Error Flags and Transmit Operations (Clock Synchronous Mode Only)
- 17.9.4 Receive Data Sampling Timing and Reception Margin in Asynchronous Mode
- 17.9.5 Note on Switching SCK3 Pin Function
- 17.9.6 Relation between Writing to TDR and Bit TDRE
- 17.9.7 Relation between RDR Reading and bit RDRF
- 17.9.8 Transmit and Receive Operations when Making State Transition
- 17.9.9 Setting in Subactive or Subsleep Mode
- 17.9.10 Oscillator when Serial Communications Interface 3 is Used
- Section 18 Serial Communication Interface 4 (SCI4)
- Section 19 14-Bit PWM
- Section 20 A/D Converter
- Section 21 LCD Controller/Driver
- Section 22 I2C Bus Interface 2 (IIC2)
- 22.1 Features
- 22.2 Input/Output Pins
- 22.3 Register Descriptions
- 22.3.1 I2C Bus Control Register 1 (ICCR1)
- 22.3.2 I2C Bus Control Register 2 (ICCR2)
- 22.3.3 I2C Bus Mode Register (ICMR)
- 22.3.4 I2C Bus Interrupt Enable Register (ICIER)
- 22.3.5 I2C Bus Status Register (ICSR)
- 22.3.6 Slave Address Register (SAR)
- 22.3.7 I2C Bus Transmit Data Register (ICDRT)
- 22.3.8 I2C Bus Receive Data Register (ICDRR)
- 22.3.9 I2C Bus Shift Register (ICDRS)
- 22.4 Operation
- 22.5 Interrupt Request
- 22.6 Bit Synchronous Circuit
- 22.7 Usage Notes
- 22.7.1 Note on Issuing Stop Condition and Start (Re-Transmit) Condition
- 22.7.2 Note on Setting WAIT Bit in I2C Bus Mode Register (ICMR)
- 22.7.3 Restriction on Transfer Rate Setting in Multimaster Operation
- 22.7.4 Restriction on the Use of Bit Manipulation Instructions for MST and TRS Setting in Multimaster Operation
- 22.7.5 Usage Note on Master Receive Mode
- Section 23 Power-On Reset Circuit
- Section 24 Address Break
- Section 25 List of Registers
- Section 26 Electrical Characteristics
- Appendix
- Main Revisions and Additions in this Edition
- Index
- Colophon
- Address List
- Back Cover
Section 14 16-Bit Timer Pulse Unit (TPU)
Rev. 2.00 Jul. 04, 2007 Page 305 of 692
REJ09B0309-0200
14.6 Interrupt Sources
There are two kinds of TPU interrupt source; TGR input capture/compare match and TCNT
overflow. Each interrupt source has its own status flag and enable/disable bit, allowing the
generation of interrupt request signals to be enabled or disabled individually.
When an interrupt source is generated, the corresponding status flag in TSR is set to 1. If the
corresponding enable/disable bit in TIER is set to 1 at this time, an interrupt is requested. The
interrupt request is cleared by clearing the status flag to 0.
Mask levels within a channel can be changed by the interrupt controller. For details, see section 4,
Interrupt Controller.
Table 14.13 lists the TPU interrupt sources.
Table 14.13 TPU Interrupts
Channel Name Interrupt Source Interrupt Flag Priority
1 TGI1A TGRA_1 input capture/compare match TGFA_1 High
TGI1B TGRB_1 input capture/compare match TGFB_1
TCI1V TCNT_1 overflow TCFV_1
2 TGI2A TGRA_2 input capture/compare match TGFA_2
TGI2B TGRB_2 input capture/compare match TGFB_2
TCI2V TCNT_2 overflow TCFV_2 Low
(1) Input Capture/Compare Match Interrupt
An interrupt is requested if the TGIE bit in TIER is set to 1 when the TGF flag in TSR is set to 1
by the occurrence of a TGR input capture/compare match on a particular channel. The interrupt
request is cleared by clearing the TGF flag to 0. The TPU has a total of four input capture/compare
match interrupts, two for each channel.
(2) Overflow Interrupt
An interrupt is requested if the TCIEV bit in TIER is set to 1 when the TCFV flag in TSR is set to
1 by the occurrence of TCNT overflow on a channel. The interrupt request is cleared by clearing
the TCFV flag to 0. The TPU has a total of two overflow interrupts, one for each channel.