To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.
Notice 1. 2. 3. 4. 5. 6. 7. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office.
User’s Manual H8SX/1663 Group E6000H FP-144L User System Interface Board HS1664ECH61H User’s Manual Renesas Microcomputer Development Environment System H8SX Family / H8SX/1600 Series HS1664ECH61HE Rev.1.00 2006.
Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage.
IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. User System Interface Board: Throughout this document, the term "user system interface board" shall be defined as the following product produced only by Renesas Technology Corp. excluding all subsidiary products.
LIMITED WARRANTY Renesas warrants its user system interface boards to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will repair or replace any user system interface boards determined to be defective in material and/or workmanship. User system interface boards are wearing parts which Renesas will not repair or replace if damaged and/or worn through use.
State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which may vary from state to state.
SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance. 2. Always switch OFF the E6000H emulator and user system before connecting or disconnecting any CABLES or PARTS. 3.
Preface The HS1664ECH61H is a user system interface board that connects a user system for the H8SX/1663, H8SX/1664 FP-144L package to the H8SX/1650 E6000H emulator (HS1650EPH60H). Emulation of the H8SX/1663 group is only possible when this user system interface board is connected to the HS1650EPH60H.
Contents Section 1 Configuration.....................................................................................1 Section 2 Connection Procedures ......................................................................3 2.1 2.2 2.3 2.4 2.5 2.6 2.7 Connecting the User System Interface Board to the User System .................................... 3 2.1.1 Installing the IC Socket........................................................................................ 4 2.1.2 Soldering the IC Socket .......
Section 1 Configuration Figure 1 and table 1 show the configuration and components of the user system interface board for the FP-144L package. Please make sure you have all of these components after you have unpacked the box.
CAUTION Use an NQPACK144SD socket (manufactured by Tokyo Eletech Corporation) as the FP-144L-packaged IC socket on the user system. Table 1 HS1664ECH61H Components No. Component Quantity Remarks 1 User system interface board 1 2 IC socket 1 For the FP-144L package (to be mounted on the user system) 3 Socket cover 1 For installing an FP-144L-packaged MCU 4 Screw (M2 x 10 mm) 4 For fastening the board 5 Screw (M2 x 6 mm) 4 For installing an FP-144L-packaged MCU 6 Spacers (2.
Section 2 Connection Procedures 2.1 Connecting the User System Interface Board to the User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting the two, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. CAUTION 1.
To connect the board to the user system, follow the instructions below. 2.1.1 Installing the IC Socket After checking the location of pin 1 on the IC socket fasten it to the user system before soldering. CAUTION After confirming the location of pin 1 on the IC socket, apply epoxy resin adhesive to the end of the four projections at the bottom of the IC socket, and fasten it to the user system. Use the guide pins provided with the product to determine where to install the IC socket, as shown in figure 2.
2.1.2 Soldering the IC Socket After fastening, solder the IC socket for an FP-144L package to the user system. CAUTION Be sure to completely solder the leads so that the solder gently covers the leads and forms solder fillets. (Use slightly more solder than with the MCU.) 2.1.3 Inserting the IC Socket Connector CAUTION Check the location of pin 1 before inserting.
2.1.4 Fastening the IC Socket Connector CAUTION 1. Use the screwdriver provided for tightening screws. 2. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening. If a screw is tightened too much, the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder. 3.
Screws (M2 × 10 mm) (for fastening the board) User system interface board Pin 1 User system IC socket (NQPACK144SD manufactured by Tokyo Eletech Corporation) Figure 3 Connecting the User System Interface Board to the User System 7
2.2 Exchanging the Spacers of the Evaluation Chip Board After connecting the user system interface board to the user system, be careful not to apply load to the user system. Exchange the spacers (2.6MP × 10 mm) of the evaluation chip board with the spacers (2.6MP × 25 mm) provided with the user system interface board and adjust the height. Evaluation chip board Spacer (2.
2.3 Connecting the User System Interface Board to the Evaluation Chip Board WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed.
Evaluation chip board Connector No. Evaluation Chip Board Connector No. Board Connector No.
2.4 Recommended Dimensions for the User System Mounting Pad (Footprint) Figure 6 shows the recommended dimensions for the mounting pad (footprint) for the user system with the IC socket for an FP-144L package (NQPACK144SD: manufactured by Tokyo Eletech Corporation). Note that the dimensions in figure 6 are somewhat different from those of the mounting pad for the system with the actual MCU. 23.00 ± 0.15 0.50 23.00 ± 0.15 11.50 11.50 2.00 ±0.10 0.50 0.25 (max.) Unit: mm Tolerance: ± 0.
2.5 Dimensions of the Evaluation Chip Board and the User System Interface Board The dimensions of the evaluation chip board and the user system interface board are shown in figure 7. 100.0 140.0 Evaluation chip board 118.5 16.0 34.5 69.0 84.5 102.5 78.5 User system interface board Unit: mm Tolerance: ± 0.
2.6 Resulting Dimensions after Connecting the User System Interface Board The dimensions of the assembly after the user system interface board has been connected to the user system are shown in figure 8. 13.3 32.9 54.9 Evaluation chip board 56.5 Spacer (φ5.8) IC socket (NQPACK144SD manufactured by Tokyo Eletech Corporation) User system 45.0 45.0 56.5 Unit: mm Tolerance: ±1.
2.7 Using the Emulator without Connecting User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting the two, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST.
USER ON SW1 USER OFF P1 Figure 9 SW1 Jumper Socket Spacer (2.
Section 3 User System Interface Circuits The following user interface circuits are required for the emulator when the user system interface board is in use.
MCU User system SN74CB3Q3306A P23 P23 SN74CB3Q3306A P27 P27 Figure 12 User System Interface Circuit (2) MCU User system SN74CB3Q3306A P14 P14 Sub-MCU SN74CB3Q3306A TXD Figure 13 User System Interface Circuit (3) 17
MCU VHC244 EPM7128 UHC14 _RES 47 kΩ _RES EPM7128 Figure 14 User System Interface Circuit (4) 18 User system Vcc
Section 4 Verifying Operation 1. Turn on the emulator according to the procedures described in the H8SX/1650 E6000H Emulator User's Manual (HS1650EPH60HE). 2. Verify the user system interface cable connections by checking the pin states with the EXMONITOR_DISPLAY command (emulator command) and checking the bus states with the MEMORY_FILL command (emulator command). If an error is detected, recheck the soldered IC socket and the location of pin 1. 3.
⎯ To use the crystal oscillator mounted on the evaluation chip board Install the crystal oscillator into the crystal oscillator terminals on the evaluation chip board.
Section 5 Points for Caution 1. Before connecting any parts or cables, make sure that the pins at the pin 1 position on both sides are correctly aligned. 2. Do not apply excessive force to the user system interface board while it is connected to the user system. 3. The dimensions of the recommended mounting pad for the IC socket for this user system interface board are different from those of the pad for the MCU. 4. This user system interface board is specifically designed for the HS1650EPH60H emulator.
8. When you use the emulator without connecting it to the user system, ensure that the SW1 jumper pin is inserted to [USER-OFF]. While no pin or SW1 jumper pin is inserted to [USER-OFF], the emulator supplies 3.3-V power to DrVCC, which is the power supply exclusively used for USB. 9. To connect the emulator to the user system, ensure that the SW1 jumper pin is inserted to [USER-ON].
Section 6 Restrictions There are the following restrictions on emulation of the H8SX/1663 group when the user system interface board is connected to the emulator. 1. The USB clock frequency is fixed to 48 MHz regardless of the EXTAL input. 2. P14 cannot be used as a port if the serial output function has already been selected. The port pin state cannot be read from the port register. 3. The user system interface board does not support subclock operation.
H8SX/1663 Group E6000H FP-144L User System Interface Board HS1664ECH61H User's Manual Publication Date: Rev.1.00, June 28, 2006 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Support Department Global Strategic Communication Div. Renesas Solutions Corp. © 2006. Renesas Technology Corp., All rights reserved. Printed in Japan.
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan RENESAS SALES OFFICES http://www.renesas.com Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
H8SX/1663 Group E6000H FP-144L User System Interface Board HS1664ECH61H User’s Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan REJ10J1395-0100