Datasheet
R01DS0190EJ0100 Rev.1.00 Page 57 of 107
Jun 19, 2013
RX111 Group 5. Electrical Characteristics
Note 1. The reference power supply current is included in the power supply current value for D/A conversion.
Note 2. Current consumed only by the USB module.
Note 3. Includes the current supplied from the pull-up resistor of the USB0_DP pin to the pull-down resistor of the host device, in addition
to the current consumed by this MCU during the suspended state.
Note 1. When OFS1.(STUPLVD1REN, FASTSTUP) = 11b.
Note 2. When OFS1.(STUPLVD1REN, FASTSTUP) = 10b.
Note 3. When OFS1.STUPLVD1REN = 0.
Note 4. Turn on the power supply voltage according to the normal startup rising gradient because the register settings set by OFS1 are
not read in boot mode.
Table 5.11 DC Characteristics (9)
Conditions: VCC = AVCC0 = VCC_USB = 1.8 to 3.6 V, VSS = AVSS0 = VREFL0 = VSS_USB = 0 V, T
a
= –40 to +105°C
Item Symbol Min. Typ. Max. Unit
Test
Conditions
Analog power
supply current
During A/D conversion
I
AVCC
—0.71.2mA
During D/A conversion (per channel)*
1
——1.5
Temperature sensor
—75—μA
Waiting for A/D, D/A conversion (all units)
——0.3
Reference
power supply
current
During A/D conversion
I
REFH0
—2552μA
Waiting for A/D conversion (all units)
——60nA
USB operating
current
During USB communication operation under the following
settings and conditions
Host controller operation is set to full-speed mode
Bulk OUT transfer (64 bytes) × 1,
bulk IN transfer (64 bytes) × 1
Connect peripheral devices via a 1-meter USB
cable from the USB port.
I
USBH
*
2
—4.3
(VCC)
0.9
(USB_VCC)
—mA
During USB communication operation under the following
settings and conditions
Function controller operation is set to full-speed
mode
Bulk OUT transfer (64 bytes) × 1,
bulk IN transfer (64 bytes) × 1
Connect the host device via a 1-meter USB cable
from the USB port.
I
USBF
*
2
—3.6
(VCC)
1.1
(USB_VCC)
—mA
During suspended state under the following setting and
conditions
Function controller operation is set to full-speed
mode (pull up the UDP0 pin)
Software standby mode
Connect the host device via a 1-meter USB cable
from the USB port.
I
SUSP
*
3
—0.35
(VCC)
170
(USB_VCC)
— μA
Table 5.12 DC Characteristics (10)
Conditions: VCC = AVCC0 = VCC_USB = 1.8 to 3.6 V, VSS = AVSS0 = VREFL0 = VSS_USB = 0 V, T
a
= –40 to +105°C
Item Symbol Min. Typ. Max. Unit Test Conditions
RAM standby voltage
V
RAM
1.8 — 3.6 V
Table 5.13 DC Characteristics (11)
Conditions: VCC = AVCC0 = VCC_USB = 0 to 3.6 V, VREFH0 = 0 to AVCC0, VSS = AVSS0 = VREFL0 = VSS_USB = 0 V,
T
a
= –40 to +105°C
Item Symbol Min. Typ. Max. Unit Test Conditions
Power-on VCC rising
gradient
At normal startup*
1
SrVCC 0.02 — 20 ms/V
During fast startup time*
2
0.02 — 2
Voltage monitoring 1 reset
enabled at startup*
3,
*
4
0.02 — —