User manual
Operating instructions
LED exterior wall lamp Prebent
Item no. 1284364
Intended use
This product is designed for use as an indoor and outdoor light. It is built according
to IP54 and can be mounted and operated both indoors and outdoors. The product is
designed to be mounted on a wall. The LED exterior wall lamp is not dimmable.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting,
re, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• Exterior wall lamp
• 2 x screws
• 2 x dowels
• 2 x washers
• Operating instructions
Meaning of symbols
The symbol with the lightning in the triangle is used if there is a risk to
your health, e.g. due to an electric shock.
The exclamation mark indicates specic risks associated with
handling, function and use.
The “arrow” symbol indicates special tips and operating information.
All metal parts that can carry voltage in the event of a fault during
operation and maintenance must be electrically connected to the
protective earth conductor.
The product is not dimmable.
This symbol reminds you to read the operating instructions included
with the product.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, ammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Also observe the safety and operating instructions of any other devices
which are connected to the product.
• Mount the light so that children cannot reach it.
• The product must only be operated using the mains voltage (see "Technical
data" section). Never try to operate the product using another type of
voltage as this will destroy the product.
• The product is designed according to protection class I; the earth wire
must be connected.
• Attention, LED light: Do not look directly into the LED light! Do not look into
the beam directly or with optical instruments!
• The product is built according to IP54 and can be mounted and operated
both indoors and outdoors. However, never mount the product in or under
water.
• Ensure that you mount the light in the correct mounting position (see
"Mounting and connection" section), otherwise there is a risk of a fatal
electric shock!
• The product must be not be operated using a dimmer.
• Do not mount and use the product in rooms or in adverse environmental
conditions that contain or may contain ammable gases, vapours or dust!
There is a risk of explosion!
• Never point a garden hose or a pressure washer etc. at the product (e.g.
for cleaning)!
• The product must only be used when mounted in a xed location. Never
mount the lamp in vehicles.
• Do not hang or secure any objects (e.g. decorations) to the product.
• Never cover the product. The surface gets hot; covering the product not
only constitutes a re hazard but may also cause it to overheat, damaging
the product.
• In industrial facilities, the accident prevention regulations for electrical
equipment and facilities issued by the Industrial Employers' Liability
Association must be adhered to!
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modications and repairs are to be performed exclusively
by an expert or at a qualied shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Preparation for mounting
Pay attention to the "Safety instructions" section.
Attention! The product must only be installed by a qualied electrician
who is familiar with the relevant regulations (e.g. VDE)! By carrying out
improper work on the mains voltage you endanger not only yourself, but
also others! If you do not know how to mount the product, get an expert to
do it for you; do not mount it yourself.
• Only mount the lamp on a stable surface. Depending on the surface, suitable screws
and dowels must be used.
• The lamp must be protected with a 10/16A fuse at the sub-distribution. An earth
leakage circuit breaker must be installed before this.
• The lamp may only be installed when it is disconnected from the power supply. It is
not sucient just to turn o the light switch!
• Isolate all poles of the mains cable from the mains supply by removing the electric
circuit fuse or switching o the circuit breaker. Then turn o the earth leakage
circuit breaker. Protect it against an unauthorised restart, e.g. with a danger sign.
• Check that the mains cable is free of current, e.g. with an appropriate testing device.