Instructions

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE. *1493869_V2_0717_02_mxs_m_en
• Connect all the components following the sequence shown on the drawing below. Make
sure to top align the arrow on the connection cable with the +5V marking on the LED strip,
otherwise the strips will not illuminate.
LED CONTROLLER
5-24V
RGB LED
Output: 3x 2A
A
B
+5V
C
D
1
E
F
4
2
2 3
2
1
1
Operating elements
1 LED strip
2 Connection cable
3 USB cable with control unit and IR receiver
4 Remote control (incl. CR2025 battery)
Operation
Using remote control
• This remote control comes with a pre-installed battery. To activate the remote control, remove
the plastic tag.
• Point the infrared sensor on the remote control in the lamp direction.
The remote control features a range of max. 5-7 m. Any objects located between the
remote control and the lights will reduce the range.
Button Feature
Increase brightness: 25% → 50% → 75% → 100%.
Decrease brightness: 100% → 75% → 50% → 25%.
ON Switch light on
OFF Switch light off
R Select RED colour
G Select GREEN colour
B Select BLUE colour
W Select WHITE colour
FLASH
Activate pre-dened ash program. Red, green and blue colours will ash
quickly. The program speed in this mode can be changed by using and
button.
STROBE
Activate pre-dened strobe program. All available colours will ash quickly.
The program speed in this mode can be changed by using and
button.
FADE
Activate pre-dened fade program. All available colours will light up
individually and simultaneously while increasing and decreasing light
intensity. The program speed in this mode can be changed by using
and button.
SMOOTH
Activate pre-dened smooth program. Seven colours will light up
individually and simultaneously while increasing and decreasing light
intensity. The program speed in this mode can be changed by using
and button.
Coloured
buttons
Select desired pre-set colour temperature.
Care and cleaning
a) Inserting/changing the battery
• Remove the battery holder from the battery
compartment as shown.
• Insert a new battery (type CR2025).
• Make sure the polarity is correct. It is shown
on the back of the remote control.
• Slide the battery holder back into the battery
compartment until it clicks into place.
Replace the batteries as soon as the lights do no longer respond to commands from
the remote control.
b) Cleaning
• Apart from the occasional battery change for the IR remote control, the product is
maintenance-free. The built-in LED bulbs are permanently installed; they cannot be replaced.
• Disconnect the product from the power supply before cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
• Clean the outside of the product with a soft, dry, ber-free cloth.
• Do not immerse the product in water.
Disposal
a) Product
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product according to
the relevant statutory regulations. Remove any inserted batteries and dispose of
them separately from the product.
b) Batteries
As the end user, you are required by law (Battery Ordinance) to return all used
batteries; disposal of them in the household waste is prohibited!
Contaminated batteries are labelled with this symbol to indicate that disposal in the
domestic waste is forbidden. The designations for the heavy metals involved are:
Cd = Cadmium, Hg = Mercury, Pb = Lead (name on batteries, e.g. below the trash
icon on the left).
Used batteries can be returned to collection points in your municipality, our stores or wherever
batteries are sold.
You thus full your statutory obligations and contribute to the protection of the environment.
Technical data
a) General
Power supply ........................................................................ USB port, 5 V/DC, max. 0.5 A
Power consumption .............................................................. 1.4 W
Protection class .................................................................... Class III
Operating conditions ............................................................. 0 to +45 ºC, 0 – 90 % RH
Storage conditions ................................................................ 0 to +45 ºC, 0 – 90 % RH
b) LED strip (each)
Length................................................................................... 0.5 m
Number of LEDs....................................... ............................ 9x LED
Dimensions (L x W) ............................................................... 500 x 10 mm
Weight ................................................................................... approx. 16 g
c) Remote control
Operational range ................................................................. max. 7 m
Power supply ........................................................................ 1 x 3 V/DC button cell,
type CR2025
Dimensions (W x H x D) ........................................................ 52 x 7 x 85 mm
Weight ...................................................................................approx. 22 g (with battery)