User manual
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the
technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE. V1_0615_02-ETS-Mkd
Operating elements
1
2
3
4
5
6
1 Indicator for power level 1
2 Display
3 Indicator for power level 2
4 +/- Button
5 MODE button
6 On/oswitch
Installation
a) Feet with castors
• Insert 2 castors all the way into both feet. Do not use any force.
• Mount both feet to the bottom of the product using the premounted screws. Note that one of the
feet features a notch for the power cable.
b) Wall installation
When drilling or tightening screws, make sure not to damage any cables, wires or
pipes located underneath the surface.
For installation in bathrooms, maintain a safety clearance of at least 60 cm to
bathtubs or showers.
The product must be installed at least 70 cm above the oor.
Do not mount any objects (e.g. shelves or cabinets) directly above the product.
Maintain a safety clearance of at least 100 cm above the product.
• Use the wall bracket as a template and mark the drill holes on the wall through the screw holes.
• Drill the holes in the wall and insert the dowels.
• Mount the wall bracket to the wall using 2 screws.
• Mount the product to the wall bracket.
• There are 2 additional brackets on the bottom of the product. Mark the drill holes on the wall
through the screw holes.
• Remove the product from the wall bracket.
• Drill the holes in the wall and insert the dowels.
• Remount the product to the wall bracket.
• Mount the brackets on the bottom of the product to the wall using 2 screws.
Operation
• Makesuretheproductisturnedo.
• Connect the power plug to a common household power outlet.
• Pressthe on/o switchto turnon theproduct.The display shows00 untilthe internalNTC
sensor registers the room temperature.
The product is set to power level 1 with a temperature of 16 °C ex works.
If the room temperature is below 16 °C, the indicator for power level 1 lights up.
• Press the MODE button to switch to power level 2. The indicator for power level 1 goes out and
the indicator for power level 2 lights up.
• On power levels 1 or 2, press the +/– button to select the desired temperature between 16 and
32°C.Theselectedtemperatureashesfor5seconds.Thenthedisplayagainshowsthecurrent
room temperature.
• Press the MODE button to switch to timer mode. There are 4 settings available: 1H, 3H, 5H or
7H. Repeatedly press the MODE button until the display shows the desired time setting. The
indicatorforpowerlevel2ashesfor5seconds.
During these 5 seconds, press the +/– button to use the timer function on power level 1.
Whentheindicatorceasesashing,pressthe+/– button to set the temperature (16 to 32 °C) for
the timer function.
• To activate antifreeze protection, press the +/– button to select the temperature setting 5 °C
(does not work in timer mode). Should the room temperature fall below 5 °C, the product will
automatically begin to heat.
Tilt and overheating protection
• Theproductfeaturestiltprotectionthatturnstheproductoautomaticallyshouldittipover.
Check the product for possible damages before continued operation. Set the product upright
and turn it back on. Make sure the product cannot accidentally tip over.
• The product also has overheating protection. The internal thermal fuse triggers when the
temperature inside the product housing exceeds 100 °C (item no. 1308749) or 90 °C (item no.
1308750).
Maintenance and cleaning
• This product does not require maintenance. There are no components located inside the product
you need to maintain. Never open/dismantle the product. Have maintenance and repairs done
byqualiedexpertsorrepairshopsonly.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they
can cause damage to the housing and malfunctioning.
• Never submerge the product in water or other liquids.
• Beforecleaning,turnoandunplugtheproduct.Allowittocooldowncompletely.
• Tocleantheproduct,adry,softandcleanclothissucient.Donotapplytoomuchpressureto
the housing to prevent scratching.
• You can use a long-haired, soft and clean brush and a vacuum cleaner to remove dust.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household
waste.
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
You thus full your statutory obligations and contribute to the protection of the
environment.
Technical data
Operating voltage.........................................230 V/AC, 50 Hz
Power input ................................................... 1000/1500 W (item no. 1308749)
650/1000 W (item no. 1308750)
Suitable for .................................................... spaces up to 10 m
2
(item no. 1308749)
spaces up to 7.5 m
2
(item no. 1308750)
Protection type ............................................. IP24
Protection class ...........................................I
Cable length .................................................. 175 cm
Operating conditions ................................... +5 to +35 ºC, 0 – 100 % RH
Storage conditions.......................................+5 to +35 ºC, 0 – 85 % RH
Dimensions (W x H x D)...............................850 x 460 x 230 mm (item no. 1308749)
550 x 460 x 230 mm (item no. 1308750)
Weight ............................................................ 5.2 kg (item no. 1308749)
3.7 kg (item no. 1308750)