V1.
Disclaimer of Warranties All UREACH flash duplicators are made specifically for data backup with legal authorities from copyright owners. Any unauthorized action of copyright is strictly prohibited, and UREACH-INC disclaims all warranties or representations of illegal actions by users. UREACH-INC also disclaims any liability for any of losses or damages due to not be able to perform its undertakings or provide any of the services attributable to any events or circumstances beyond our control.
Before you start Important Notice ▸▸ Read the complete operation instruction carefully contributes to better operation. ▸▸ Make sure the source device is correct and workable. ▸▸ To guarantee data consistency, strongly suggest the capacity of source and targets should be the same. ▸▸ It is strongly suggest to use “Copy+Compare” to achieve a perfect duplication. Safety Precautions ▸▸ The warranty will expire if damage is incurred resulting from noncompliance with theses operating instructions.
Content Index 6 Setup 6.1 Copy Area 6.1.1 System and Files 6.1.2 All Partitions 6.1.3 Whole HDD 6.1.4 Percentage(%) 6.2 Skip Error 6.3 Language 6.4 Advanced Setup 6.4.1 Unknown Format 6.4.1.1 Copy Unknown 6.4.1.2 Skip Unknown 6.4.2 Erase Master 6.4.3 Erase Pattern 6.4.3.1 ONE Byte 6.4.3.2 Big Random Data 6.4.4 Wait HDD Time 6.4.5 Transfer Rate 6.4.6 Stop Motor Time 6.
1Features Chapter ➀ - Product Introduction ▸▸ High copy speed supports up to 250MB/second. ▸▸ Support reading/writing speed measuring function. ▸▸ Show the detailed information of HDD and its quality. ▸▸ Auto power control system helps to protect the HDD from any damage during the insertion and removal from the duplicator. ▸▸ Support compatibility of multiple interfaces via external adapters:2.5”/3.5” IDE HDD, mSATA SSD , eSATA , iVDR , microSATA , CF, cFAST, SSD. Support HDD interfaces: 1.8" / 2.5"/ 3.
Chapter ➀ - Product Introduction 2Product Overview 2.1 System Overview Red : Fill Flashing Green : Operating Remain Green : Pass Port 1 (Source) Yellow : Power Supplying Port 4 (Target 3) Port 2 (Target 1) Backward Forward Comfirm/OK Cancel/Back Port 3 (Target 2) 2.
Chapter ➀ - Product Introduction 3Function Table Function Description 1. Copy To copy source HDD to multiple target HDDs. Refer to function [6.1 Copy Area] for 4 different copy modes selection. 2. Compare To compare data bit for bit between source and target HDDs. 3.Copy +Compare It makes copy first and then compare target HDD with source HDD to ensure data correctness. 4.1 Quick Erase To erase HDD’s index table only, it takes short time to execute this function. 4.
Chapter ➀ - Product Introduction 5.2.1 Update BIOS To update the system firmware via the HDD. 5.2 Update System 5.2.2 Create Update HDD To format the HDD with a 2GB FAT partition in order to quickly save the new firmware in the HDD. 5. Utility 5.3 System Info. This function will show information of the duplicator system, including controller model, number and software version. 5.4 Read Speed To show the speed of reading. 5.5 Write Speed To show the speed of writing. 6.1.
Chapter ➀ - Product Introduction 6.4.5 Transfer Rate 6.4 Advanced Setup 6. Setup Select the proper transfer rate from UDMA2~UDMA7. 6.4.6 Stop Motor Time Auto running time after stopping motor. 6.5 Restore Default Back to original manufacturer setting.
Chapter ➁ - Function Introduction 1Copy It copies data from the source HDD to the target HDD. Please ensure you have selected the copy mode require before executing the copying process. Refer to function [6.1 Copy Area] for details. Copy Process Copie Time Copy 0:26 2047M 1037M 50% Total data capacity Copied data capacity Copy Process % Copy Result Pass 0:58 No Bad Sector! Note The default setting is the quick copy mode “System and Files”.
4Erase Chapter ➁ - Function Introduction There are Quick Erase, Full Erase, DoD Erase, DoD EraseComp , and Secure Erase, totally 5 kinds of erasing modes. Select the appropriate erase method when you would like to dispose or reuse the HDDs. Note • Users can go to Function [6.4.2 Erase Master] to select if erasing the source HDD. The default setting is “Disable” to erase the source HDD. • This function can be stopped while processing by pressing [ESC] for about 3~4 seconds. 4.
Chapter ➁ - Function Introduction Erasing. Erasing 1 HDD DoD Erase 2:05 [02] Erase[00] 465G 4818M The system will show the result after finishing. DoD Erase Pass: 5 Fail: 0 4.4 DoD Erase Comp As well as DoD erase, this function will also execute compare function to make sure the random bit was correctly written.
Chapter ➁ - Function Introduction 4.5 Secure Erase The international authorized high standard Secure Erase function. It overwrites every single track on the hard drive with "00". Even PA/DCO or other data area which are not able to load, can be erased all together. Note Please do not disrupt during Secure Erase, otherwise it would cause irretrievable error on HDD, which turns the HDD unusable. 5Utility 5.1 Show Disc Info. The function will show basic information of both source and target HDDs. 5.1.
Chapter ➁ - Function Introduction 5.1.4 Device Power Cycle This function is to show the count of HDD's turning on and off. [Disc Info.] 4.Device Power C [Device Power C] 99 5.1.5 Power-on Hours This function is to show the total hours of HDD powering-on. [Disc Info.] 5.Power-on Hours [Power-on Hours] 18 5.1.6 Reallocation Event Count This function is to show the count of reallocating event. When the HDD fails to save data, it will need to redefine the location to store data.
Chapter ➁ - Function Introduction 5.1.8 Seek Error Rate This function is to show the error rate of searching for data. It can represent the damage rate of data stored in the HDD. [Disc Info.] 8.Seek Error Rat [Seek Error Rat] 0 5.1.9 Temperature This function is to show the temperature of HDD. [Disc Info.] 9.Temperature [Temperature] 22 o C 5.2 Update System This function is to execute firmware updating of system. You can follow the following steps to update the system firmware.
Chapter ➁ - Function Introduction ⊳ Download the BIOS from the PC to your HDD. HDD USB HDD Enclosure PC ⊳ Plug the HDD into Port 1of the duplicator, select Function 5.2.1 to update BIOS, and wait for about 1 minute to finish the update process. [Update System] 1.Update BIOS 5.3 System Info. This function shows the duplicator information such as model name and firmware version. HDD Dupe 1-1 Ver: 2.31.0 5.4 Read Speed This function is to measure the reading speed of the HDD by reading the whole HDD.
Chapter ➁ - Function Introduction 5.5 Write Speed This function is to measure the writing speed of the HDD by writing the whole HDD. [5.Utility] 5.Write Speed Content will be erased. Confirm? W 1:08 89.6M/S Note 465G 4423M This function will delete the content in HDD, so please make sure you have backup data before executing this function. 6Setup 6.1 Copy Area This setting is to select the copy mode you would like to use. 6.1.
Chapter ➁ - Function Introduction Source HDD 320GB Data : 20GB Partition1 : 90GB Note Tatget HDD 320GB When choosing “System and Files Copy”, only 20G data will be copied, and it just takes 6.2% time compared to “Whole HDD Copy”. The target HDD will be exactly the same as source HDD after copy. System and Files only supports FAT, NTFS, and LINUX (ext2/ ext3/ ext4). 6.1.2 All Partitions This mode will copy all of the partitions areas bit by bit including the free space.
6.1.3 Whole HDD Chapter ➁ - Function Introduction This mode will copy the entire HDD, regardless of content, format, partition or free space. This mode will take much more time to duplicate the source HDD completely. [Copy Area] Whole HDD Source HDD 320GB Data : 20GB Partition1 : 90GB Note Tatget HDD 320GB When choosing “Whole HDD Copy”, completed 320GB HDD will be copied, and it takes the longest time. The target HDD will be exactly the same as the source HDD after copy.
Chapter ➁ - Function Introduction Source HDD 500GB Data:250GB Partition:250GB Tatget HDD 500GB Only percentage range from25% to 32% will be copied. 25% 25% 32% 32% 500GB 6.2 Skip Error This function sets the volume of errors that is acceptable for you to skip during the copy process. [Skip Error] 0 Note If it’s critical that there are no errors on the HDD, then the error counter should be set to 0. 6.3 Language Select preferred language. 6.4 Advanced Setup 6.4.
Chapter ➁ - Function Introduction 6.4.1.1 Copy Unknown The setting copies all the unknown area even if the format is not identified. [Unknown Format] Copy Unknown 6.4.1.2 Skip Unknown The setting skips the unknown format area during copy process. [Unknown Format] Skip Unknown 6.4.2 Erase Master This function is to set if erasing the source or not when executing erasing function. [Erase Master] Disable [Erase Master] Enable 6.4.
Chapter ➁ - Function Introduction 6.4.3.2 Big Random Data A set of different random character to be written into a set of area. This erase pattern method is safer for preventing from data recovered. [Erase Pattern] Big Random Data 26A5C8781 BF51337E81 AA9641D3B 5CDA756B1 3BAFF21FF4 1FBAC4C99 7EDAF1237 7F51C59C3 6.4.4 Wait HDD Time You can select auto-start time after plugging in HDD, able to set the waiting time from 0 to 30 seconds. [Wait HDD Time] 15 seconds 6.4.
Chapter ➁ - Function Introduction [Stop Motor Time] 8 Seconds 6.5 Restore Default This function is to go back to the manufacturer's default setting.
Chapter ➂ - Specification Product Name Carry Mini Super High Speed HDD Dupe. Product Number PRO368 Targets 1:3 (4-port) Transfer Speed 250MB/sec Support HDD Interface 1.8”/2.5”/3.5” SATA HDD and SSD Display 2x16 Monochrome LCD Control Button 4 push buttons( ▲ , ▼ , OK, ESC ) Compatible HDD/SSD All major brand of 2.5"/3.5" IDE HDD, mSATA SDD, eSATA, microSATA, iVDR, CF, cFAST, USB3.0 Duplication Mode 1.System and Files 2.All Partitions 3.Whole HDD 4.
U-Reach The Data Equipment Expert www.ureach-inc.
