Modular Point Source Array Modules Associated 15 Inch Subwoofer VA101-7 & VAX101-7 Series VA101-15 & VAX101-15 Series VA101-22 & VAX101-22 Series VA15S & VAX15S Subwoofer Users Manual
Point Source Array Modules Introduction To VARIA The VARIA loudspeaker family includes 3 fullrange array modules and a 15 inch subwoofer. All have been designed to offer the ultimate in versatility and performance. When used as a stand alone loudspeaker each array module is a powerful 10 inch loudspeaker that can be easily mounted on a tripod stand or pole mounted on the associated subwoofer. All 3 models offer a wide range of horizontal coverage options.
Point Source Array Modules The VARIA Hardware Concept The array modules have heavy metal side channels and each module is provided with 2 heavy joining bars (one for each side) and associated quick release pins so it can easily be stacked with similar modules For example , -7 modules with other -7 modules. Joining unlike modules, for example joining -7 modules with -15 modules requires special joining bars, called "biscuits". See list below.
Point Source Array Modules VA/VAX101-7 Array Module VA / VAX15S Subwoofer “Stand Alone” Applications VARIA array modules are equipped with dual Metric M10 attachment points top and bottom so they can be easily flown using eye bolts. Multi-angle pole sockets bottom mounted and side mounted flying hardware add further to their versatility.
Point Source Array Modules Stand Alone Applications (cont) The array modules and the subwoofers are joined together with heavy-duty tie bars and quick-disconnect pins that provide quick and easy assembly along with metal-to-metal reliability. Ground stacks of this type can easily handle up to 3 array modules and two subwoofers. Assembling a ground stack is as easy as A,B,C. A. First position the subwoofer and then set the next cabinet on top of it making sure the metal channels are aligned See Figure 1.
Point Source Array Modules Vertical Line Arrays Most vertical line arrays are not assembled in a straight line as their name implies. Instead they are constructed in either a curved or a J shape or a combination of both shapes to obtain the proper sound coverage. The shape of the array is typically determined by the flying hardware and the splay between the cabinets can easily be different than what is optimum from an acoustical standpoint.
Point Source Array Modules Assembling Vertical Line Arrays 1. Attach the RHANG101LA Flybar to the top cabinet using the quick release pins. Note the bridle construction which allows you to move the suspension bar laterally and adjust the array’s tilt (aiming angle). Move the bridle toward the rear of the cabinets for more tilt.
Point Source Array Modules Assembling Vertical Line Arrays (continued) 1 2 3 One of the situations you may run into is you want to use a number of 7.5 degree modules at the top of a tall vertical array , but the 7.5 degree tilt provided when two -7 modules are tight packed provides to much tilt. Fortunately, the VA101-7's connecting bar is hinged and allows you to vary the aiming angle from 7.5 degrees down to 0 degrees in half degree steps.
Point Source Array Modules This page intentionally left blank for future expansion of ground stacking instructions Page 9
Point Source Array Modules Horizontal Arrays The skillful design, complementary cabinet angles and tightly controlled dispersion that allow the sonic outputs of VARIA array modules to be smoothly mixed to obtain the desired coverage perform just as well in horizontal arrays as they do in vertical line arrays. R-HANG-VA101H Joining two VA101-22 22.5º modules together in a horizontal array or cluster produces a seamless 45º horizontal pattern; use three 22.5º modules for 67.
Point Source Array Modules Simulation Software EASE and EASE Focus II Simulation Software Varia101 GLL data in EASE and EASE Focus II simulation software tools allows you and system designers to quickly and accurately predict the performance of individual Varia loudspeakers and of Varia arrays in various settings.
Point Source Array Modules Rear Panel Connections & Controls VAX101 Connections Screw Terminal Strip Inputs Looping In & Out Neutrik 4-Pin Speakon Connectors Array Module High Frequency Control Not all setups are identical and neither are all rooms. That is why the VAX series non-powered array modules include a rear mounted high frequency level control. The high frequency level control allows you to adjust the high frequency output of each array module to compensate for: 1.
Point Source Array Modules RHAON Empowered VARIA Array Module Connections Power LED Thermal LED Primary Analog Input XLR female Looping Analog Output XLR male Secondary Analog input & Looping Output Signal & Overdrive LED Status Indicators Input Pad & LED Indicator Fault Detect Push Button Volume Controls Fault Relay Mute Buttons AC Power On/Off Switch Primary & Secondary Ethernet (CobraNet) Inputs RJ-45 female AC Line Voltage Selector AC Line Fuse IEC Power Connector The input panel shown
Point Source Array Modules VA101-x-52R & VAX101-x Array Modules Technical Specifications Sensitivity VA101-x-52R: 1.0 V for RPO VAX101-x: 96 dB (1W/1m) Freq.
Point Source Array Modules PF2-500 Digital Amplifier Technical Specifications Output Power: LF: 500 W RMS @ 4 Ohms HF: 100 W RMS @ 4 Ohms Freq. Resp: +0.0, -.5 dB, 20 Hz to 20 kHz THD Distortion: < 0.02% typical Hum & Noise: <100 dB (A weighted) Damping: >100 Input: 10K Ohm balanced differential Sensitivity: 1.0 V for RPO CMR: 74 dB Input Connectors CobraNet; Dual RJ45 connectors; accept Cat 5 copper cable.
Point Source Array Modules VA101 & VAX101 Dimensional Drawings VA101-22-52R VAX101-22 Top View 15” 23 3/4” VA101-15-52R VAX101-15 13” 15” Front View VA101-22-52R VAX101-22 End Views Bottom View VA15S-R & VAX15S Dimensional Drawing Metric M10 Attachment Points (typical for 8) 22 1/2” Treaded Pole Socket 6 1/8” 23 3/4 “ 19” Page 16
Point Source Array Modules VA15SR & VAX15S Technical Specifications VA15S-5R: 115 V AC or 230V AC VAX15S: 800 W Pgm @ 8 Ohms Connectors: VA15S-5: See PF1-500R amplifier below VAX15S: Screw terminals, Looping 4-pin Neutrik Speakon connectors Sensitivity VA15S: 1.0 V for RPO VAX15S: 97 dB (1W/1m) Max SPL VA15S: 127 dB peak VAX15S: 129 dB peak Freq.
Page 18 AMP GAIN OUTPUT DELAY POLARITY CROSSOVER CENTER FREQUENCY TYPE SLOPE EQ #1 CENTER FREQUENCY Bandwidth BOOST/CUT EQ #2 CENTER FREQUENCY Bandwidth BOOST/CUT EQ #3 CENTER FREQUENCY Bandwidth BOOST/CUT EQ #4 CENTER FREQUENCY Bandwidth BOOST/CUT VAX101-7 2.7 kHz .3 -2 dB 4.5 kHz .6 +2 dB 13 kHz .7 +9 dB 570 Hz 0.4 -3.0 dB 1 kHz 0.4 -4.0 dB NONE NONE NONE 1.7 kHz HP LINKWITZ-RILEY 24 dB/ Oct 1.5 kHz .3 3 dB 1.6 kHz LP LINKWITZ-RILEY 24 dB/ Oct -11 dB NONE NORMAL HF 125 Hz 0.4 4.
Point Source Array Modules NOTES: 1. The EQ settings shown are for a single array module and may need “fine tuning” in multi cabinet arrays. 2. When the VAX101-7 is being used with a VAX15S subwoofer the VAX101-7 should be delayed 2.7 ms.
Page 20 AMP GAIN OUTPUT DELAY POLARITY CROSSOVER CENTER FREQUENCY TYPE SLOPE EQ #1 CENTER FREQUENCY Bandwidth BOOST/CUT EQ #2 CENTER FREQUENCY Bandwidth BOOST/CUT EQ #3 CENTER FREQUENCY Bandwidth BOOST/CUT EQ #4 CENTER FREQUENCY Bandwidth BOOST/CUT VAX101-15 2.2 kHz .250 -3 dB 3.2 kHz .7 -3.0 dB 13 kHz .7 +9 dB 520 Hz 0.4 -1.5 dB 1.1 kHz .5 -4.0 dB 1.8 kHz .3 2.0 dB 1.7 kHz HP LINKWITZ-RILEY 24 dB/ Oct 1.7 kHz .3 3 dB 1.7 kHz LP LINKWITZ-RILEY 24 dB/ Oct -11 dB NONE NORMAL 125 Hz 0.4 4.
Point Source Array Modules NOTES: 1. The EQ settings shown are for a single array module and may need “fine tuning” in multi cabinet arrays. 2. When the VAX101-15 is being used with a VAX15S subwoofer the VAX101-15 should be delayed 2.7 ms.
Page 22 AMP GAIN OUTPUT DELAY POLARITY CROSSOVER CENTER FREQUENCY TYPE SLOPE EQ #1 CENTER FREQUENCY Bandwidth BOOST/CUT EQ #2 CENTER FREQUENCY Bandwidth BOOST/CUT EQ #3 CENTER FREQUENCY Bandwidth BOOST/CUT EQ #4 CENTER FREQUENCY Bandwidth BOOST/CUT VAX101-22 2.6 kHz .4 -4 dB 4.7 kHz .35 -1.5 dB 13 kHz .7 +9 dB 520 Hz 0.4 -1.5 dB 1.1 kHz .5 -4.0 dB 1.8 kHz .3 2.0 dB 1.6 kHz HP LINKWITZ-RILEY 24 dB/ Oct 1.7 kHz .3 4 dB 1.7 kHz LP LINKWITZ-RILEY 24 dB/ Oct -7.5 dB NONE NORMAL 125 Hz 0.4 4.
Point Source Array Modules NOTES: 1. The EQ settings shown are for a single array module and may need “fine tuning” in multi cabinet arrays. 2. When the VAX101-22 is being used with a VAX15S subwoofer the VAX101-22 should be delayed 2.7 ms.
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
