Owners manual

ManualsBrandsRenovators Supply ManualsBathroomRenovator's Supply Dual Flush Corner Toilet Round White Porcelain Chrome Button

Table Of Contents

These instructions and drawings disclose condential and other data of proprietary nature

owned by Renovator's Supply Inc.

and may not be used or disclosed to others without the

prior written consent of Renovator's Supply Inc.

Renovators Supply, Inc.© www.rensup.com

Please Read The Following Instructions Before Installing.

NOTE: It is not recommended to pre-install or rough-in the product before actually receiving it

on location. This is due to slight variations in the product.

Preparation and disassembly:

1. Shut o water supply to the existing water closet

2. Disconnect water supply tubing from existing tank and angle stop valve

3. Remove existing water closet and tank from oor

4. Remove old wax seal and clean area around the drain

Toilet Bowl Installation

1. To install the toilet bowl tum it upside-down.

Place the new wax ring (available at any hardware or plumbing supply store)

and sleeve over the drain horn. Press it down rmly. Note: if the ring has a

paper cover, remove it.

2. Make sure the toilet ange is clean and the oor bolts point straight up.

Carefully position the toilet bowl over the ange, and t the holes in the

toilet base directly over the oor bolts.

3. Press down on the toilet bowl to compress the wax ring. To form a tight

seal. Attach the washers and nuts to the oor bolts, and tighten them with

a (non-scratch) adjust able wrench.

(Note: Don't over-tighten the bolts as you may crack the ceramic base).

Toilet Bolt Covers are available at rensup.com

17612 White

17613 Bone

17614 Black

Our No Slam Toilet Seats are available at rensup.com

White round 14349, elongated 13506.

Bone round 15390, elongated 15389.

Summary of content (4 pages)

PAGE 1
Renovators Supply, Inc.© www.rensup.com Please Read The Following Instructions Before Installing. NOTE: It is not recommended to pre-install or rough-in the product before actually receiving it on location. This is due to slight variations in the product. Preparation and disassembly: 1. Shut off water supply to the existing water closet 2. Disconnect water supply tubing from existing tank and angle stop valve 3. Remove existing water closet and tank from floor 4.
PAGE 2
Renovators Supply, Inc.© www.rensup.com Please Read The Following Instructions Before Installing. NOTE: It is not recommended to pre-install or rough-in the product before actually receiving it on location. This is due to slight variations in the product. Standard 12 inch rough-in: 12” Corner 12 inch rough-in: 12” 12” These instructions and drawings disclose confidential and other data of proprietary nature owned by Renovator's Supply Inc.
PAGE 3
Renovators Supply, Inc.© www.rensup.com Before installing, remove old fittings and clean tank. Do NOT useplumber’s putty to seal fittings. Do NOT use chlorine (bleach) cleaners or related products. Note: valves shown below may vary in appearance from the actual valves you may have received. Top Push Button Button Nut Refill Tube Overflow Pipe Float Clip Stainless Steel Lift Rod Arm Valve Lid Valve Body Seal Washer Plastic Washer Lock Nut Move the slide up or down to adjust half flush.
PAGE 4
Renovators Supply, Inc.© www.rensup.com Refill Tube Dual Flush Valve 1. Disassemble the lock nut for valve installation. Position the valve inside the tank. Push down on the valve body while tightening the lock nut from outside. Dual Push Button 1. 3. 2. Position the rubber washer Position the tank gasket on the lock in the lock nut. nut & position the tank on the toilet bowl. Fasten the tank to the toilet bowl using tank bolts. NOTE: tighten bolts simoultaneously. 2.