Installation Guide

Contents of Bathroom Fixtures
Robe Hook (03)
1 - Mounting Plate
2 - Plastic Anchor
2 - Mounting Screws
1 - Rosette
1 - Hook with Setscrew
Euro Tissue (07)
1 - Mounting Plate
2 - Plastic Anchor
2 - Mounting Screws
1 - Rosette
1 - Assembled Tissue arm
with Setscrew
Standard Tissue (08)
2 - Mounting Plate
4 - Plastic Anchor
4 - Mounting Screws
2 - Rosette
2 - Posts (1 left & 1 Right)
1 - Plunger assembly
18” or 24” Towel Bar (18 or 24)
2 - Mounting Plate
4 - Plastic Anchor
4 - Mounting Screws
2 - Rosette
2 - Posts (1 left & 1 Right)
1 - Towel Bar (Either 18” or 24”)
Towel Ring (86)
1 - Mounting Plate
2 - Plastic Anchor
2 - Mounting Screws
1 - Rosette
1 - Assembled Towel Ring
with Setscrew
Mounting
Plate
Posts
Left Side
Set screw should
be on bottom
Right Side
Set screw should
be on bottom
Robe Hook
(03)
Euro Tissue
(07)
Standard Tissue
(08)
18”
Towel Bar
(18)
Towel Ring
(86)
24”
Towel Bar
(24)
Screw, Anchor
& Allen Wrench
1. Locate where Robe Hook should be installed
2. Mark holes by using mounting plate as template
3. Drill 1/4” holes in wall and install plastic anchors
ush with nished wall
4. Place mounting plate on wall and secure with
screws provided
5. Place Robe Hook on the Rosette style you have
chosen by inserting square on bottom of Robe Hook
into square in center of Rosette
6. Slide both Rosette and Robe Hook onto mounting
plate. You may need to loosen the installed set screw
with the allen wrench provided.
7. Press the Robe Hook rmly to the wall and tighten
set screw with the allen wrench provided.
Robe Hook (03)
1. Locate where Euro Tissue should be installed
2. Mark holes by using mounting plate as template
3. Drill 1/4” holes in wall and install plastic anchors ush with nished wall
4. Place mounting plate on wall and secure with screws provided
5. Place Euro Tissue assembly on the Rosette style you have chosen by inserting square on bottom of
Euro Tissue into square in center of Rosette
6. Slide both Rosette and Euro Tissue assembly onto mounting plate. You may need to loosen the installed
set screw with the allen wrench provided.
7. Press the Euro Tissue rmly to the wall and tighten set screw with the allen wrench provided.
Euro Tissue(07)
1. Locate where Standard Tissue should be installed
2. Mark holes by using mounting plate as template
3. Drill 1/4” holes in wall and install plastic anchors ush with nished wall
4. Place mounting plate on wall and secure with screws provided
5. Place Standard Tissue assembly on the Rosette style you have chosen by inserting square on
bottom of Standard Tissue into square in center of Rosette
6. Slide both Rosette and Standard Tissue assembly onto mounting plate. You may need to loosen
the installed set screw with the allen wrench provided.
7. Press the Standard Tissue rmly to the wall and tightenset screw with the allen wrench provided.
Standard Tissue(08)
TIP - Put posts on mounting plates
without Rosettes and insert the
plunger between them. Locate on
wall were it’s comfortable to you,
level, and mark the holes in the
mounting plates
1. Locate where Towel Ring should be installed
2. Mark holes by using mounting plate as template
3. Drill 1/4” holes in wall and install plastic anchors
ush with nished wall
4. Place mounting plate on wall and secure with
screws provided
5. Place Towel Ring on the Rosette style you have chosen by inserting
square on bottom of Towel Ring into square in center of Rosette
6. Slide both Rosette and Towel Ring onto mounting plate. You may
need to loosen the installed set screw with the allen wrench provided.
7. Press the Towel Ring rmly to the wall and tighten set screw with
the allen wrench provided.
Towel Ring (86)
1. Locate where Towel Bar should be installed
2. Mark holes by using mounting plate as template
3. Drill 1/4” holes in wall and install plastic anchors ush with nished wall
4. Place mounting plate on wall and secure with screws provided
5. Place Towel Bar assembly on the Rosette style you have chosen. Insert square
on bottom of Towel Bar into square in center of Rosette
6. Slide both Rosette and Towel Bar assembly onto mounting plate. You may need
to loosen the installed set screw with the allen wrench provided.
7. Press the Towel Bar rmly to the wall and tighten set screw with the allen
wrench provided.
18” Towel Bar (18)
24” Towel Bar (24)
TIP - Put posts on mounting plates
without Rosettes and insert the
bar between them. Locate on
wall were it’s comfortable to you,
level, and mark the holes in the
mounting plates