Install Instructions

ManualsBrandsResideo Braukmann ManualsHeating Supplies3/4" Sweat Union Mixing Valve (LF)

Table Of Contents

INSTALLATION INSTRUCTIONS

62-3075EFS-09

CUS

Braukmann

AM-1 Series

PROPORTIONAL THERMOSTATIC MIXING AND DIVERTING VALVE STANDARD AND “C”

TEMPERATURE RANGE MODEL

APPLICATION

The AM-1 Series family of quality valves in a variety of

temperature ranges and connections, for master mixing or

diverting applications.

SPECIFICATIONS

Media Temperature Ranges:

Cold Inlet: 39°F-80°F (4°C-27°C)

Hot Inlet: 120°F-180°F (49°C-82°C)

Mixed Outlet:

C Model: 70°F-120°F (21°C-49°C)

Standard Model: 70°F-145°F (21°C-63°C)

Connections:

Straight-through design (HOT and COLD at same level).

Construction:

Nickel plated brass construction. EPDM o-rings. Made in

USA.

Lead Free Plumbing Code Compliance: The wettable sur-

faces of lead free models contain less than .25% of lead by

weighted average

Operating Pressure: 150 psi (1034 kPa) maximum.

Patent Information: U.S. Patent No. 6,079,625.

Temperature Gauge Adapter: Lead-free brass,

EPDM o-ring

INSTALLATION

IMPORTANT

Mounting must comply with all local codes.

NOTE TO INSTALLER:

This product should be installed by a

qualified individual, in accordance with local codes and

ordinances. It is the responsibility of the installer to properly

select, install and adjust these devices as specified in these

instructions. For installations which require compliance with

Building/Mechanical/Plumbing Codes, the appropriate AM-1

Series valve must be chosen and installed, and the discharge

temperature set and locked according to these instructions.

AM-1 “C” Series models with the temperature range, 70°F–

120°F (21°C–49°C) and "Standard" models with temperature

range 70°F–145°F (21°C–63°C) are ASSE

1017 (point of

source application) certified, and CSA

®a

and IAPMO

listed.

These models shall be used to supply water to tubs, showers,

bathing facilities and other outlets. These valves should be

installed where they will be accessible for cleaning, servicing

or adjustment.

ASSE 1017 Applications—Point of

Source

These AM-1 Series models can be installed in any position

consistent with the intended use. For domestic hot water

supply, the valve must be installed as shown in Fig. 1. There

shall be no shut-off valves installed between the cold water

line and the cold water connection on the AM-1 Series valve.

Check valves shall be installed as indicated for NPT models;

all AM-1 models with union fittings are supplied with integral

check valves on both the hot and cold ports. A cold water

service valve may be installed, as indicated, between the cold

water supply line to the distribution system and the cold

water line supplying both the water heater and the AM-1

Series valve.

NPT

Union

Press

Temperature

Gauge

Push

Connect

CPVC

PEX

-UCPVC and -UPEX models are not CSA listed.

Summary of content (12 pages)

PAGE 1
Braukmann AM-1 Series PROPORTIONAL THERMOSTATIC MIXING AND DIVERTING VALVE STANDARD AND “C” TEMPERATURE RANGE MODEL INSTALLATION INSTRUCTIONS INSTALLATION IMPORTANT Mounting must comply with all local codes. Press Union CPVC Temperature Gauge NPT NOTE TO INSTALLER: This product should be installed by a qualified individual, in accordance with local codes and ordinances. It is the responsibility of the installer to properly select, install and adjust these devices as specified in these instructions.
PAGE 2
AM-1 SERIES WATER USE FIXTURES THERMOMETER RECIRCULATION T (1) PUMP AM SERIES C M TO DISHWASHER IF PERMITTED BY CODES T AQUASTAT (1) CHECK VALVE ALLOWABLE SERVICE VALVE LOCATION (1) H 8 (203) MAX WATER HEATER THERMOWELL HEAT TRAP 6 (152) V EXPANSION TANK COLD WATER SUPPLY SCREW O-RING THERMOMETER ADAPTER WITH UNION NUT M25029A Fig. 1. AM-1 Series ASSE 1017 application. Dimensions shown in in (mm).
PAGE 3
AM-1 SERIES Thermostrip Installation Clean pipe and firmly apply Thermostrip on mix outlet of valve. Flow water and adjust mixed outlet temperature for desired setting range. Actual mixed water temperature is indicated in green with 2° F (1° C) increments. Blue means slightly lower and brown means slightly higher. WARNING Water Temperature above 120°F (49° C) can cause serious injury. Mixing valve temperature setting should be done by licensed contractor per local code requirement.
PAGE 4
AM-1 SERIES Table 1. AM-1 Series Replacement Kits. Part No. Model Description AM-1-020RP C 70 °F-120 °F (21 °C-49 °C) Thermostatic Element Replacement Kit AM-1-025RP STD 70 °F-145 °F (21 °C-63 °C) Thermostatic Element Replacement Kit AM1-TG100-US-LF/U ALL 1/2" (12.7 mm) AM1 Temp Gauge Tail PC w/Sweat AM1-TG101-US-LF/U ALL 3/4" (19 mm) AM1 Temp Gauge Tail PC w/Sweat AM1-TG102-US-LF/U ALL 1" (25.4 mm) AM1 Temp Gauge Tail PC w/Sweat TG200-UT/U ALL Thermometer, 2" (50.
PAGE 5
Braukmann Série AM-1 VANNES DE MÉLANGE ET DE RÉPARTITION À DÉBIT PROPORTIONNEL ET MODÈLE DE PLAGE DE TEMPÉRATURES « C » INSTRUCTIONS D’INSTALLATION Adaptateur de l'indicateur de température : Laiton sans plomb, joint torique EPDM INSTALLATION Raccord Presse PVC-C Indicateur de À compression température NPT IMPORTANT L'installation doit être conforme à tous les codes locaux en vigueur.
PAGE 6
Série AM-1 APPAREILS CONSOMMANT DE L’EAU THERMOMÈTRE RECIRCULATION T (1) POMPE SÉRIE AM M VERS LE LAVE-VAISSELLE SI LE CODE LE PERMET T AQUASTAT (1) CLAPET ANTIRETOUR EMPLACEMENT PERMIS POUR LE ROBINET DE SERVICE (1) C H 8 (203) MAX CHAUFFEEAU PIÈGE À CHALEUR 6 (152) V RÉSERVOIR D’EXPANSION PUITS THERMOMÉTRIQUE ARRIVÉE D’EAU FROIDE VIS JOINT TORIQUE ADAPTATEUR DU THERMOMÈTRE AVEC ÉCROU-UNION MF25029A Fig. 1. Application ASSE 1017 de la vanne AM-1. Dimensions en po (mm).
PAGE 7
Série AM-1 vanne retrouve son fonctionnement d'origine. Dans certains cas, il peut être nécessaire de remplacer les pièces inférieures. Installation de la bande thermique Nettoyer la canalisation et appliquer fermement la bande thermique à la sortie d'eau mélangée. Faire couler l'eau et ajuster la température à la sortie d'eau mélangée jusqu'à obtenir la gamme de température souhaitée. La température réelle de l'eau mélangée apparaît par incrément de 1 °C (2 °F).
PAGE 8
Série AM-1 Tableau 1. Trousses de remplacement de la gamme AM-1. No de pièce Modèle Description AM-1-020RP C 70 °F à 120 °F (21 °C à 49 °C) Trousse de remplacement de l'élément thermostatique AM-1-025RP STANDARD 70 °F à 145 °F (21 °C à 63 °C) Trousse de remplacement de l'élément thermostatique AM1-TG100-US-LF/U TOUS Indicateur de température PC avec soudure AM1 de 1/2 po (12.
PAGE 9
Braukmann AM-1 Series MEZCLADORAS TERMOSTÁTICAS PROPORCIONALES Y NORMA DE LA VÁLVULA DE DISTRIBUCIÓN Y MODELO DE RANGO DE TEMPERATURA “C” INSTRUCCIONES DE INSTALACIÓN Conector del termómetro: Latón libre de plomo, Junta de EPDM INSTALACIÓN Press Union CPVC Termómetro NPT Conexión a presión IMPORTANTE El montaje debe cumplir con todos los códigos locales. NOTA PARA EL INSTALADOR: Este producto debe instalarse por una persona calificada, de acuerdo con los códigos y reglamentos locales.
PAGE 10
AM-1 SERIES ARTEFACTOS DE USO DE AGUA TERMÓMETRO RECIRCULACIÓN T (1) BOMBA AM SERIES C M AL LAVAPLATO, SI LO PERMITE LA REGLAMENTACIÓN T AQUASTAT (1) VÁLVULA DE RETENCIÓN UBICACIÓN AUTORIZADA DE LA VÁLVULA DE SERVICIO (1) H 8 (203) MAX CALENTADOR DE AGUA TRAMPA DE CALOR 6 (152) V TANQUE DE EXPANSIÓN TERMOPOZO FUENTE DE AGUA FRÍA TORNILLO JUNTA ADAPTADOR DE TERMÓMETRO MS25029A Fig. 1. Aplicación ASSE 1017 de AM-1 Series. Dimensiones en pulg. (mm).
PAGE 11
AM-1 SERIES Instalación de la tira térmica Limpie el tubo y aplique con firmeza la tira térmica en la salida mezcladora de la válvula. Haga correr el agua y ajuste la temperatura de salida al rango deseado. La temperatura real del agua mezclada se indica en verde con incrementos de 2° F (1° C). El azul significa que la temperatura es ligeramente menor y el marrón indica que es apenas mayor. ADVERTENCIA Temperaturas superiores a los 120° F (49° C) pueden provocar lesiones serias.
PAGE 12
AM-1 SERIES Tabla 1. Kits de reemplazo Serie AM-1. Pieza n.º Modelo Descripción AM-1-020RP C 21 °C-49 °C (70 °F-120 °F) Kit de reemplazo de Kit de reemplazo de cartucho termostático inferior AM-1-025RP STD 21 °C-63 °C (70 °F-145 °F) Kit de reemplazo de Kit de reemplazo de cartucho termostático inferior AM1-TG100-US-LF/U TODOS 1/2" (12.