User Guide English Nasal Pillows System
Fitting / Anlegen / Mise en place / Applicazione 1 2 3 Adjustment / Anpassen / Ajustement / Regolazione
Removal / Abnehmen / Retrait / Rimozione Disassembly / Auseinanderbau / Démontage / Smontaggio 1 2
Reassembly / Zusammenbau / Remontage / Riassemblaggio 1 2 3
English AirFit™ P10 NASAL PILLOWS SYSTEM Thank you for choosing the AirFit P10. This document provides the user instructions for the AirFit P10 and AirFit P10 for Her masks referred to collectively as AirFit P10 throughout this manual. AirFit P10 has blue headgear while AirFit P10 for Her has pink headgear. Using this guide Please read the entire guide before use. When following instructions, refer to the images at the front and back of the guide.
2 the device is turned on and functioning properly, new air from the device flushes the exhaled air out through the mask vent holes. However, when the device is not operating, insufficient fresh air will be provided through the mask, and the exhaled air may be rebreathed. Rebreathing of exhaled air for longer than several minutes can, in some circumstances, lead to suffocation. This applies to most models of CPAP or bilevel devices. Follow all precautions when using supplemental oxygen.
Refer to your CPAP or bilevel device manual for details on settings and operational information. Remove all packaging before using the mask. Using your mask When using your mask with ResMed CPAP or bilevel devices that have mask setting options, refer to the Technical specifications section in this user guide for mask selection options. For a full list of compatible devices for this mask, see the Mask/Device Compatibility List on www.resmed.com on the Products page under Service & Support.
3. Finally, connect the end of the mask tubing into your device air tubing. Your mask is now fitted and ready to use. When the device is running, a light breeze should be felt through the vent. To inspect the vent place a finger close but not over the entire vent area. Adjustment To achieve a comfortable fit, adjust the split straps by spreading them apart to loosen or draw them closer together to tighten.
Cleaning your mask at home Your mask and headgear should only be gently handwashed. The mask vent may discolour over time due to dust. Follow the cleaning instructions in this guide to maintain performance and safety of the mask. WARNING Always follow cleaning instructions and use mild soap. Some cleaning products may damage the mask, its parts and their function, or leave harmful residual vapours that could be inhaled if not rinsed thoroughly.
When all components including the vent are dry, reassemble according to the reassembly instructions. Weekly: Handwash the headgear in warm (approximately 30°C) water using mild soap. It may be washed without being disassembled. Rinse well and allow it to air dry out of direct sunlight. Reprocessing the mask between patients This mask should be reprocessed when used between patients. Cleaning, disinfection and sterilisation instructions are available from the ResMed website, www.resmed.
Problem/possible cause Solution Vent is blocked or dirty/discolored. If the vent requires cleaning, use a soft bristle brush. The vent may discolor over time and this is not a safety concern. Follow the cleaning instructions in this guide to maintain performance and safety of the mask. Ensure the vent is dry after cleaning and in the case of excess condensation. Vent is wet. Mask too noisy System is assembled incorrectly. System is leaking air.
Resistance Sound Environmental conditions Gross dimensions Mask setting options Drop in pressure measured (nominal) at 50 L/min: 0.4 cm H2O at 100 L/min: 1.4 cm H2O DECLARED DUAL-NUMBER NOISE EMISSION VALUES in accordance with ISO 4871. The Aweighted sound power level of the mask is 21 dBA, with uncertainty of 3 dBA. The A-weighted sound pressure level of the mask at a distance of 1 m is 13 dBA, with uncertainty of 3 dBA.
Symbols The following symbols may appear on your product or packaging: Catalog number Batch code Humidity limitation Temperature limitation Fragile, handle with care Not made with natural rubber latex Manufacturer European Authorised Representative Keep away from rain This way up Indicates a Warning or Caution and alerts you to a possible injury or explains special measures for the safe and effective use of the device Caution, consult accompanying documents.
Mask components / Maskenkomponenten / Composants du masque / Componenti della maschera A Headgear / Kopfband / Harnais / Copricapo 1 Split-strap headgear / Geteiltes Kopfband / Harnais avec sangle à lanière double / Copricapo con cinghia con fenditura 2 Buttonhole / Knopfloch / Boutonnière / Asola 3 Fabric end / Textilende / Extrémité en tissu / Estremità in tessuto B Pillows / Nasenpolster / Coussins / Cuscinetti 4 Nasal pillows / Nasenpolster / Coussins narinaires / Cuscinetti nasali C Frame
B+C A+B+C AirFit P10 AirFit P10 for Her * Pillows system / Nasenpolstermaske / Masque narinaire / Cuscinetti nasali 62920 (XS) 62921 (S) 62922 (M) 62923 (L) 62920 (XS) 62921 (S) 62922 (M) 62923 (L) Complete system / Komplettes System / Système complet / Maschera con tutti i componenti 62901 62911 XS Extra Small / Extra Small / Très petit / Extra Small S Small / Small / Petit / Small M Medium / Medium / Médium / Medium L Large / Large / Grand / Large
1 2 3 * * 4 5 6 7 8 Global leaders in sleep and respiratory medicine www.resmed.com 618265/1 2013-10 Manufacturer: ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia. Distributed by: ResMed Corp 9001 Spectrum Center Boulevard San Diego CA 92123 USA. ResMed (UK) Ltd 96 Jubilee Ave Milton Park Abingdon Oxfordshire OX14 4RW UK. See www.resmed.com for other ResMed locations worldwide. For patent information, see www.resmed.com/ip. AirFit is a trademark of ResMed Ltd. © 2013 ResMed Ltd.
