User's Manual

ManualsBrandsResolution Products ManualsElectronicsWiFi Home Automation Device

RE926S Wifi Module

Features

•

Connects in the daughter board slot of a GE SimonXT security panel.

•

Allows reporting of alarm status conditions over Wifi connection to a home internet

network.

•

Allows control of system functions (arming, disarming, etc.) over Wifi connection.

•

Allows control of additional wireless sirens in alarm conditions.

•

Easy Wifi connection to existing secured network using WPS functionality.

Key Instructions

•

Power down the SimonXT panel, and open the back cover.

•

Install the RE926S unit into the slot at the back of the panel.

•

Power up the panel.

•

Press the button labeled WPS on the RE926S until the red Wifi LED starts flashing.

•

Press the WPS button on the Wifi router or access point.

•

Wait until the security information is exchanged and a stable connection is made, this may

take one to two minutes to complete.

•

Close the back cover on the panel.

•

Connect to configuration software and enter MAC address.

•

Configure RE926S to correct IP address for reporting.

•

Configure RE926S to correct IP address for system control.

LED Operation

•

The Wifi LED should be lit red when connected to Wifi network, and may flicker when

sending and receiving network data.

•

Power LED lights green when powered and shows a 'heartbeat' for processor functioning

correctly.

•

CS LED lights when connected to Central Station

•

Platform LED lights when connected to interactive platform website.

RE926S Wifi Module User Manual Page 1 of 5

www.resolutionproducts.com

Summary of content (5 pages)

PAGE 1
RE926S Wifi Module Features • Connects in the daughter board slot of a GE SimonXT security panel. • Allows reporting of alarm status conditions over Wifi connection to a home internet network. • Allows control of system functions (arming, disarming, etc.) over Wifi connection. • Allows control of additional wireless sirens in alarm conditions. • Easy Wifi connection to existing secured network using WPS functionality. Key Instructions • Power down the SimonXT panel, and open the back cover.
PAGE 2
Specifications Panel Compatibility: Power Supply: Current draw: PCB dimensions: GE/Interlogix SimonXT 9-18V DC, minimum 100mA. 70-85mA, normal operation 1.9 x 4.1 inches Specifications subject to change without notice. Internal Pictures Top view: Factory Default Switch Daughter board connector Status LEDs Wifi Module External Siren Connector WPS Button Side view: RE926S Wifi Module User Manual Page 2 of 5 www.resolutionproducts.
PAGE 3
OEM Installation Instructions The RE926S module is installed in the GE SimonXT host as follows: 1. The SimonXT panel should be powered down, with battery unplugged. 2. Open the panel and expose the back. 3. Unwrap the module from its packaging and carefully slide the module underneath the plastic tabs at the top of the expansion slot. 4. Gently press down on the bottom of the module so that it engages with the connector on the panel. 5. Secure the module in place using four screws in the corner holes. 6.
PAGE 4
Notices: “GE” is a trademark owned by General Electric Company. “Interlogix” is a trademark of UTC. This Resolution Product is not produced by, endorsed by, or officially associated with GE or UTC. Resolution recommends verifying operation at installation. This product is only usable with the GE/Interlogix SimonXT alarm panel. FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference.
PAGE 5
IC Notice This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1)This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.