E100 Wirefree Alarm System Installation & Operating Manual
FOREWORD CONTENTS Your decision to purchase an Eclipse Wirefree Solar Alarm System represents a major and sensible step towards total protection of your premises, its contents and its occupants. INTRODUCTION The Eclipse Wirefree Solar Alarm System complies with the requirements of BS6799 Class 1 for Wireless Alarms. All components are designed and manufactured to provide a high standard of security protection and long, reliable service.
INTRODUCTION The Eclipse Wirefree Solar Alarm System contains all components necessary to install a complete system. Wirefree items included are: 1 x Wirefree External Solar Siren 2 x PIR Movement Detectors 1 x Remote Control 2 x Wirefree Passive Infra Red Movement Detectors (PIR’s) Wirefree External Solar Siren PANIC ON OFF Wirefree Remote Control WP1.
PLANNING AND EXTENDING YOUR WIREFREE ALARM SYSTEM For even greater protection you can fit as many PlR Movement Detectors and Magnetic Contact Detectors as and when you require. The Eclipse Alarm System is designed to give you protection for a two bedroomed house. Just add additional detectors where further protection is needed.
WIREFREE EXTERNAL SOLAR SIREN GENERAL INFORMATION HOUSING The Siren and Solar Panel are all encapsulated within a tough polycarbonate housing. This housing provides full protection against adverse weather conditions. All electronic components are specially treated to ensure long, reliable, trouble free operation and an integral tamper switch gives maximum security protection to the unit.
Solar Panel Front cover locating tabs Receiver Aerial 7.5 Volt DC charging adaptor input Dip switch cover Tamper switch Bleep Disable Link P2 Siren Disable Link P3 P1 J.D. Link 1 2 3 4 5 6 7 8 6 Volt 1.
Detection. In order to detect any attempts to illegally jam the radio channel used with your alarm system a special jamming detection function is incorporated into the Solar Siren. If this feature is selected, and the radio channel is jammed continuously for 30 seconds, when the system is armed, the Solar Siren will emit a pre-alarm series of rapid bleeps for 5 seconds. If the jamming continues for a further 10 seconds or more a full alarm condition will occur.
WIREFREE PASSIVE INFRA RED MOVEMENT DETECTORS (PlR’s) Two Passive Infra Red Movement Detectors are supplied in the standard package. However, additional Passive Infra Red Movement Detectors can be purchased separately, if required. Passive Infra Red Movement Detectors are designed to detect movement within a protected area. The detector element detects differences in Infra Red radiation when a person moves within the protected area.
Anti Tamper Switch House Code ON 1 2 3 ON 1 2 3 4 5 6 7 8 9 10 4 5 6 7 8 9 10 IMPORTANT Switch 9 MUST BE "ON" Switch 10 MUST BE "OFF" Backplate Fixing Screw View inside PIR Movement Detector Battery Compartment SETTING THE WIREFREE PASSIVE INFRA RED MOVEMENT DETECTORS (PIR’s) 1. Using a ball-point pen, set the miniature switches 1 - 8 to the same combination of ‘ON’ and ‘OFF’ as the dip switches in the Solar Siren. 2. Ensure that dip switch 9 is set to ‘ON’.
3. Fix the detector and magnet to the opening using either the double sided tape OR screws provided. 4. Using a ball-point pen, set the miniature switches 1-8 to the same combination of ‘ON’ and ‘OFF’ as the dip switches in the Solar Siren. Before fixing the detector to a metal door/window check the radio range as previously described.
To test the optional Magnetic Contact Detectors, Arm the system using the remote control. Open the protected door/window and ensure that the Solar Siren goes into Alarm Mode. Disarm the system using the Remote Control. Test each Magnetic Contact Detector by arming and disarming the system and operating each detector in turn. When you have completed testing leave the Solar Siren in the Disarmed Mode. You may test your system at any time.
battery(ies) as required turn the Solar Siren back to Disarmed Mode. Note: When replacing PIR batteries, fit PP3 Alkaline type. Rechargeable batteries should NOT be fitted. MAINTENANCE Your Wirefree Alarm System requires very little maintenance. However, a few simple tasks will ensure its continued reliability and operation. SOLAR SIREN 1. At least once a year, preferably in the Autumn, the solar panel on the top of the siren housing should be cleaned using a soft, damp cloth.
TROUBLE SHOOTING Symptom / Recommendation Siren gives full alarm condition when arming 1. Rear anti-tamper switch on siren is open - ensure that it is pressed fully closed. The wall is possibly uneven, the siren may need relocating to a more suitable position. Symptom / Recommendation PIR Movement Detector not detecting a person’s movement 1. Ensure ‘House Codes’ are the same in the Solar Siren and Remote Control. 2. Solar Siren in Service Mode.
EXTENDING YOUR E100 WIREFREE ALARM SYSTEM You may add Wirefree Magnetic Contact Detectors and additional Wirefree PIR Detectors etc. from the CA2000 range of accessories as required, to give additional protection where needed. The following accessories are also available to extend and enhance your system. ACCESSORIES STROBE UPGRADE CA2000STR STROBE UPGRADE (This part only) Add to your existing Siren Unit to give full Siren & Strobe protection.
If you need help, just dial the Helpline for expert technical support: 01372 450960 (Lines open 9.00am to 6.00pm, Monday to Friday). We can solve most problems quickly over the phone. GUARANTEE This product (excluding Alkaline batteries) is guaranteed for one year from the date of purchase against faulty materials or workmanship. We will repair or replace any faulty product.
ECLIPSE E100 SPECIFICATION External Solar Siren Wirefree Remote Control 315 mm 1 2 3 4 ON OFF 98 mm 70 25 mm 225 mm 85 mm ● Case material 3mm Polycarbonate ● Dual front and rear anti-tamper ● Internal receiver and aerial UK ● ● ● ● ● ● ● ● ● ● ● ● RESEARCH & DEVELOPMENT Our R & D Department is constantly developing new products. We practice a policy of continued improvement and reserve the right to change specifications without prior notice.
