Wireless MP3 USB Door Chime Kit Model: User Manual SC379
Contents Before you start 3 Kit Components Safety Precautions 3 3 Installation 4 Battery Installation 4 Bell Push Portable Door Chime Unit Installation Instructions 4 4 5 Bell Push Chime Position 5 6 Chime Sounds 6 Setting Up 7 Programming Proceedure 7 Download a) Auto-Run b) Editing c) Build up the Play List d) Play or Delete in the Play List 2 7 7 7 8 8 e) f) g) h) Synchronize Memory Disconnect Tune/chime sound selection Digital Code Set Up 1 First Time Operation 8 9 9 9 9 9 2
Before you start ■ Unpacking Unpack your chime kit and identify the following parts: • • • • • • Chime Unit Bell Push 4 x Push Inserts (1 x each white, black, silver, brass colour) USB Cable Fixings User Manual ■ Safety Precautions Before proceeding with the installation please note the following safety warnings: • Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc.
Installation ■ Battery Installation Bell Push The Bell Push is operated by 1 x 3volt CR2032 Lithium battery (included) The Lithium battery (CR2032) has been installed. To activate the battery remove the battery cover by inserting a small flat-bladed screwdriver into the recess and push the battery cover forward. Remove the isolation strip from the battery compartment, then snap the cover back on. The Bell Push is now ready to use.
Portable Door Chime Unit Remove the battery cover by pushing upwards on the arrow and insert 2 x 1.5volt alkaline batteries (“C”, UM2 & R14 – not included), ensure the battery polarity matches the internal markings. The door chime is ready to learn the operation code (please see Digital Code set up).
Chime Position The chime can be free standing or wall mounted. 3mm ■ Chime Sounds Bell Push The chime sound selector is located inside the Bell Push, a small switch on the top right corner of battery compartment marked with “S”. Press the switch once, the chime sound will change to play the next tune on the list.
Setting Up ■ Programming Proceedure Download: The programme supports: Windows 2000, XP, Vista and Windows 7. Firstly create a folder to store your music/chime sounds in MP3 or WAV format and save to your “Desktop”. Connect the USB cable between the chime unit and your computer. The program will auto-run. Your computer will show the download programme display.
and drag your mouse to the end of selected section, then release the left button, the window at bottom right corner of the soundwave bar will show the duration time of this section. You can play the selected section by pressing the play button on the bottom left corner of the sound wave bar. Note: The music/chime sound duration time used as a door chime sound should be 8-15 seconds.
the Play List in the memory. The “Synchronize is finished” icon will pop up for confirmation. Note: Always synchronize your door chime before disconnecting the USB cable. f) Memory: The door chime has 8 MB of memory and will store approximately 8-9 minutes of music/chime sounds. The memory bar shows the percentage of memory used. g) Disconnect: Disconnect the USB cable, the door chime is ready for use.
2 Interference from a similar unit operating nearby (i.e. the chime sounds when the Bell Push has not been operated): a) Remove the batteries from the Bell Push and Door Chime units and rest for 10 seconds, this will erase the memory. b) Insert the batteries into the Bell Push and Door Chime units, the chime unit is now ready for the new code registration.
e) It is important to remember that when you replace your chime batteries that you will need to follow the same procedure of pairing the devices as above. Important: Repeat this procedure after changing the Push Button battery. Note: If the Chime Unit sounds for no reason during the digital code setting, it is indication that there is interference by other similar door chime unit(s) nearby, reset the digital code as (2) above.
Low Battery Indicator The red LED indicator on the Door Chime Unit will flash when the chime batteries need replacing. Important: a) If mounting the Bell Push onto a metal surface or a UPVC door frame the operation range will be reduced. Always test the operating range prior to fixing the Bell Push into its permanent position. b) Do not mount either Unit close to a heat source or expose to high temperature. c) Do not use a different type of batteries, or mix up old and new batteries.
Troubleshooting If the door chime unit does not sound, please check the following: a) Batteries in the Bell Push and Door Chime units, if flat change the batteries. e) Units are out of range - operate the Chime Unit within the operation range. b) Wrong battery polarity in either Bell Push or Door Chime units – reinsert the batteries.
Specification ■ Door Chime Operation Operating Temperature: 0C to +35C Operating Distance: Up to 100 metres (330ft approx. in open field & at suitable conditions) The Chime Unit can be mounted or portable for use around the home, workshop, office or garden. The transmission range of the wireless signal will be reduced if the signal is transmitted through a number of walls or ceilings. Metal and UPVC doorframes will also reduce the operating range.
Tunes/chime sounds: a) Supports all MP3 format (All i-Pod MP-3 files cannot be supported) V1 – MPEG Version 1, V2 – MPEG Version 2 & Version 2.5, L1 – Layer I, L2 – Layer II, L3, Layer III. Sampling rate frequency index (values are in Hz) bits: MPEG1 44,100 48,000 32,000 MPEG2 22,050 24,000 16,000 MPEG2.5 11,025 12,000 8,000 (b) Support all WAV files. Batteries: Bell Push: Power: Door Chime unit: 1 x 3volt CR2032 Lithium battery (included) 2 x 1.
Telephone Helpline: 0845 373 1353 Local Rate Call Response Electronics Limited, Roman House, Lysons Avenue, Ash Vale, GU12 5QF www.responseelectronics.com SC379 Ed.