Night Stand Contains One (1) Night Stand and Hardware IMPORTANT NOTE: Carefully remove all the parts from the box. Arrange on a flat TOOLS REQUIRED: surface and verify you have all of the following parts and hardware. Phillips Screwdriver For customer support please call 314-993-2693. -Hammer 1.Top Panel (1 PC) 2.Left Side Panel (1 PC) 3.Right Side Panel (1 PC) 4.Bottom Panel (1 PC) 5.Back Panel (1 PC) Bar Panel | | (2 PCS) 7.Side Bar Panel (2 PCS) 8.Legs L/R (4 PCS) 9.Drawer Front Panel 2 PCS) 10.
HARDWARE LIST A.Allen Key (1 PC) B.Dowel (8 PCS) C.JCBC W Screw 40mm (4 PCS) D. Minifix Bolt (20 PCS) E. Minifix House (20 PCS) F. Minifix Cap (20 PCS) G.Screw 16mm (36 PCS) H.Screw 50mm (16 PCS) LL Bracket (4 PCS) fmm J. Handle (PCS) K.Drawer Slider 2 SET) L.
ASSEMBLY INSTRUCTIONS STEP 1 & Tap Dowels (Part B) into the Left and Right Side Panel (Part 2,3) in the larger holes provided.
ASSEMBLY INSTRUCTIONS Attach the Drawer Slider (Part K) to the Left Side Panel (Part 2) using Screw 16mm (Part the Pilot Holes as marked. Attach the Drawer Slider (Part K) to the Right Side Panel (Part 3) using Screw 16mm (Part the Pilot Holes as marked.
ASSEMBLY INSTRUCTIONS ‘5 Toe bond of to mii fix 557 housing goes to the open ‘mouth of the mini ix bolt. «| Ruthenium tho mini fix Say Rousing so it frightens over the mini fx bolt. Insert the Mini fix House (Part E) to the Right Side Panel (Part 3) and make sure the open side of the Mini fix House (Part E) is facing the opening on panels.Attached the Right Side Panel (Part 3) as shown. Tum the Mini fix House (Part E) fo tighten using the Allen Key (Part A) or screwdriver.
ASSEMBLY INSTRUCTIONS STEP 7 Insert the Back Panel (Part 5) into the back of the nightstand by sliding the Back panel into the slots provided. BACK VIEW This is how to insert back panel STEP 8 Attach the Bottom Panel (Part 4) to the Left and Right Side Panels (Part 2,3) using CBC W Screw 40mm (Part C) and Allen Key (Part A) as shown.
ASSEMBLY INSTRUCTIONS STEP 9 “This is how a mini fix works... Insert the Mini fix House (Part E) to the Front and The head of the mini fix Back Bar Panel (Part 6) and Side Bar Panel (Part and make sure the open side of the Mini fix &. You Thea turn the mini fx House (Part E} is facing the opening.Attach the ” Sy oe Legs (Part 8) as shown. Turn the Mini fix House (Part E) to tighten using the Allen Key (Part A) or screwdriver.
ASSEMBLY INSTRUCTIONS STEP 11 et a BACK VIEW Insert the Mini fix House (Part E) to the Legs (Part 8), make sure the open side of the Mini fix House (Part E) is facing the opening. Turn the Mini fix House (Part E) fo Tighten using the Allen Key (Part A) or screwdriver.Cover the Mini fix House using the Mini fix Cap (Part F) by pressing it into the Mini fix House Attach White Nail (Part L) to each corner of the Left and Right Panel (Part 2,3) using hammer as shown.
ASSEMBLY INSTRUCTIONS STEP 13 Attach Drawer Back Panel (Part 10) to Drawer Side Panels (part 11) using Screw 50mm (Part H) and a Phillips Screwdriver as shown. Back View STEP 14 Attach Drawer Slider (Part K) to the Back View Drawer Side Panels (Part 11) using Screw 16mm (Part G) and a Phillips screwdriver. Attach the Handle (Part J) to the Drawer Front Panel (Part 9) using Handle Screw 16mm (Part G) and a Phillips screwdriver. Tighten the screws.