Use Instructions

ManualsBrandsRETEVIS ManualsElectronicsTwo Way Radio

8.4 Scan channel

This function needs to be set by the dealer through PC software. Channel scanning can search for a signal channel. When there is a

signal on the scanned channel, the walkie-talkie will stop on the channel for you to talk.

The scanning mode can be set to [Carrier] or [Time].

Set to [Carrier], that is, if the scanned channel has a signal, the walkie-talkie will always stay on this channel, and continue scanning

when there is no signal.

Set to [Time], that is, the scanned channel has a signal, and the intercom will stay for a period of time. If the machine does not operate,

it will continue to scan.

After the PC software is set up, by pressing the [Scan] shortcut key, the walkie-talkie can scan. When the walkie-talkie is in the

scanning state, press the [Scan] shortcut key to stop scanning.

8.5 TOT

This function needs to be set by the dealer through PC software. The transmission time limit function prevents users from occupying

the channel for too long. If the continuous transmission time exceeds the time programmed by the dealer, the two-way radio will stop

transmitting and sound a warning tone. To stop the warning tone, release the [PTT] key. If you need to transmit again, you can press

and hold the [PTT] key again.

9 Common failure phenomena and troubleshooting methods.

Can’t turn on

The voice is too low

Can't talk

A. The battery is dead: please fully charge the dedicated charger

and try again or replace with a new battery;

B. Poor volume switch or other problems: please go to the

designated repair station for repair;

A. Too far away from the microphone of the walkie talkie when

speaking: the best distance is 3-10cm;

B. The volume setting is wrong: turn the volume switch clockwise to

increase the volume;

A. The channel parameters are not set correctly: reset the

parameters and try again;

B. The group identity of the default call is incorrect: please select the

correct person and try again;

C. The call distance of the walkie talkie is exceeded;

Number Failure phenomenon Causes and troubleshooting

SPECIFICATIONS

GENERAL

Channel: 30CH

Working voltage: 7.4V DC

Weight: 310g(including antenna

and battery)

Dimension: 129X63X39mm

TRANSMITTER

Frequency range: GMRS

RF power: 5W/0.5W

Modulation type: FM

Spurious radiation: <-36dBm

Modulation noise: >40dB

Modulation distortion: <3%

Frequency stability: 2.5ppm

Max Fr. Deviation: <5kHz

Audio response: +6.5~-14dB

RECEIVER

Frequency range: GMRS

Receiving sensitivity: <-121dBm

Selectivity: >60dB

Audio power output: 1W@16R

Modulation distortion: <3%@1W

Frequency stability: 2.5ppm

Current: Current standby 55mA,

working 300mA

Audio response: +7~-12.5dB

Frequency

CH.NO RX Freq.(MHz) TX Freq.(MHz) CTCSS/DCS ERP

462.5625

462.5875

462.6125

462.6375

462.6625

462.6875

462.7125

467.5625

467.5875

467.6125

467.6375

467.6625

467.6875

467.7125

462.5500

462.5750

462.6000

462.6250

462.6500

462.6750

462.7000

462.7250

462.5500

462.5750

462.6000

462.6250

462.6500

462.6750

462.7000

462.7250

462.5625

462.5875

462.6125

462.6375

462.6625

462.6875

462.7125

467.5625

467.5875

467.6125

467.6375

467.6625

467.6875

467.7125

462.5500

462.5750

462.6000

462.6250

462.6500

462.6750

462.7000

462.7250

467.5500

467.5750

467.6000

467.6250

467.6500

467.6750

467.7000

467.7250

67.0

118.8

127.3

131.8

136.5

141.3

146.2

D243N

D032N

D047N

D051N

D053N

D065N

D116N

123

D743I

D332I

127.3

D243I

D606N

D731I

136.5

0.5W

For further resources: Brochures, Software/Firmware, Manual and Declaration-of-Conformity, Pls contact your direct reseller OR

go to web retevis.com, and check "support" in the each product link to download it