2400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 448 PULLOUT BASE ORGANIZERS TOOLS REQUIRED: 3 7 32 64 2 mm #2 3 8 ESTIMATED ASSEMBLY TIME: 20 MIN CARE AND MAINTENANCE: Clean with a damp cloth and wipe parts dry.
STEP 1 Disengage cabinet slide assembly from unit by pressing release levers on the two vertical slides and pulling unit away from cabinet slide assembly (See Figure 1). FIG. 1 NOTE: Center slide does not have a release lever, pull strongly to separate. STEP 2 Center cabinet slide assembly on cabinet floor 7/8” from front outside edge of cabinet (See Figure 2). FIG. 2 Note: If installing into a cabinet with an inset door, move the slide assembly back additionally the thickness of the door.
STEP 4 Engage product slide assembly to cabinet slide assembly (Fig 4). FIG. 4 Note: Before engaging be sure to move the ball bearing tracks found inside the cabinet slide assembly forward so they are flush with the black mouth piece caps. STEP 5 Attach door to unit using (4) 6 x 1/2” flat head screws. (See Figure 5). Note: Utilize the adjustable door mounting brackets to ensure mounting in thick portion of cabinet door (front of product should line up with front of face frame).
Door Adjustment Section STEP 6 FIG. 6 To add tilt to your door: Tighten or loosen “Adjustment Screw” until cabinet door is at desired position. whether it be to the left, right, top, or bottom, use the adjustment screw (Figure 6A). Adjustment Screws Note: Each corner can be adjusted independently. STEP 7 To adjust your cabinet door side to side use a 3/8” nut driver, you will want to use the “Lock Nut” adjustment, refer to Figure 7 for the “Lock Nut” location. FIG.
12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 INSTRUCCIONES DE INSTALACIÓN / LES INSTRUCTIONS D’INSTALLTION ORGANIZADORES DE BASE EXTRAÍBLE 448 448 ORGANISATEUR COULISSANT POUR BAS D’ARMOIRE HERRAMIENTAS REQUERIDAS: OUTILS REQUIS: 3 7 32 64 2 mm #2 3 8 TIEMPO ESTIMADO DE ENSAMBLADO: DUREE ESTIMÉE DE L’ASSEMBLAGE: 20 MIN CUIDADO Y MANTENIMIENTO: ENTRETIEN ET MAINTENANCE: Limpie con un paño húmedo y seque las partes.
PASO 1 / ÉTAPE 1 Retire el conjunto de deslizamiento del gabinete de la unidad presionando las palancas de liberación de los dos deslizadores verticales y separando la unidad del conjunto de deslizamiento (Observe la Figura 1). FIG. 1 NOTA: La corredera central no tiene una palanca de liberación, hale con fuerza para separarla.
PASO 4 / ÉTAPE 4 Enganche el conjunto de deslizamiento del producto al conjunto de deslizamiento del gabinete (Fig. 4). FIG. 4 Nota: Antes de enganchar, asegúrese de mover las surcos de los rodamientos que se encuentran dentro del conjunto de deslizamiento del gabinete hacia adelante para que queden al ras con las tapas negras de la boquilla. Enclenchez le module coulissant au module de l’armoire (fig. 4).
Sección de ajuste de la puerta Section d’ajustement de la porte PASO 6 / ÉTAPE 6 FIG. 6 Tornillos de ajuste Vis d’ajustement Para agregar inclinación a su puerta: Apriete o afloje el “Tornillo de ajuste” hasta que la puerta del gabinete esté en la posición deseada. ya sea a la izquierda, derecha, arriba o abajo, use el tornillo de ajuste (Figura 6A). Nota: Cada esquina se puede ajustar de forma independiente.