Instructions / Assembly

Step 6. Add Dimension A and B together. Measure this distance from
bottom of the inside cabinet door and mark a horizontal line.
(See gure 4)
Due to the many dierent door styles, overlays, and cabinet constructions, the Rev-A-Shelf door mount brackets provide the ultimate in exibility for
ensuring that the positioning of the hole pattern on the door bracket installs with the thick portion of any cabinet door frame. Thus, eliminating any need
for adding a sub door panel.
Step 7.
Take Dimension C from Step 4 and divide it by two. Measure this
distance to the left of the center point on the inside of the cabinet door
and make a vertical line. Measure this distance to the right of the center
point on the inside of the cabinet door and make another vertical line.
(See gure 5)
Step 7
Take Dimension C (from Step 4)
and divide it by two. Measure this
distance to the left of the center point
on the inside of the cabinet door and make a
vertical line. Measure this
distance to the right of the center
point on the inside of the cabinet
door and make another vertical line
(See illustration 6)
Step 8
Remove Door Brackets from product
members and screw to inside of cabinet
door with #6 x 1/2'' flat head screws.
NOTE: Line up door bracket to cabinet door
by aligning door bracket with the vertical and
horizontal lines you have marked in Steps 6
& 7.
(See illustration7)
Step 9
Hang door with brackets attached on
the mounting screws on to the product
members. Tighten bottom screws
securly. Tighten top screws (with
washer) snugly allowing for future
adjustment.
(See illustration 8)
Step 6
Add Dimension A and Dimension B
together. Measure this distance from
bottom of the inside of your cabinet
door and mark a horizontal line.
(See illustration 5). Measure center
point on inside of cabinet door and mark
this point as well.
A+B
Center
Dimension C
Equal
Equal
Step 10.
Be sure bumper pads are installed to all four
corners of door. Push door closed and apply
pressure to all four
corners making sure
door is flush with cabinet.
(See illustration 9).
Step 11.
Pulling from bottom,
pull door open.
(See illustration 10).
Securly tighten
top screws.
Step 12.
If your cabinet door is not straight
(even all around) you can adjust it
by loosing the screws on one of the
sides, properly align the cabinet
door and re-tighten the screws.
Helpful Hints:
There are several different
ways to mount the Door
Brackets to your cabinet
door ensuring that you
are mounting to the
thick portion of the door.
For instance, spacers can
be used when mounting Door Brackets to the
Product Members (spacer kit included). The Door
Bracket can also be installed on the inner side of the
Product Member.
Illustration 5
illustration 8
illustration 6
ilustration 7
If your door is parallel but slightly
off center. Loosen screws
that attach the slide mounting feet
to the cabinet floor, slide assembly
sideways as needed and re-tighten
screws.
2409 Plantside Drive
Jeffersontown, KY 40299
800-626-1126
502-491-2215 fax
illustration 9
illustration 10
Door...
off left
to right
Door...
crooked
all around
Door...
straight
after
ajustment
Door...
straight
after
ajustment
Door
Door
Door
I-RV-DM KIT
Step 5. Measure the distance from the bottom face frame to the bottom
of the door mount bracket, Noted as Dimension A. Measure your door
overlap. Noted as Dimension B as shown in gure 3. NOTE: On
frameless cabinets, measure from the cabinet oor to the bottom of the
door bracket.
Installing Door Mount Brackets on Cabinet Door
Mounting
Instructions
Step 1. Remove left and right door mount brackets. Leave product
member attached.
Step 2. Remove cabinet door and hinges. Place the product inside
cabinet. NOTE: If a rear wood bin is included, remove for installation.
Step 3. Center the wood frame left to right in the opening.
Position the front of the wood frame even with the front of the face frame
as shown in gure 1. Attach to bottom of cabinet using (5) #8 x 5/8” pan
head screws (included). (See gure 1)
Step 4. Re-install door mount brackets as shown in gure 2. Measure
outside to outside dimension of door brackets. This is Dimension C.
Step 7
Take Dimension C (from Step 4)
and divide it by two. Measure this
distance to the left of the center point
on the inside of the cabinet door and make a
vertical line. Measure this
distance to the right of the center
point on the inside of the cabinet
door and make another vertical line
(See illustration 6)
Step 8
Remove Door Brackets from product
members and screw to inside of cabinet
door with #6 x 1/2'' flat head screws.
NOTE: Line up door bracket to cabinet door
by aligning door bracket with the vertical and
horizontal lines you have marked in Steps 6
& 7.
(See illustration7)
Step 9
Hang door with brackets attached on
the mounting screws on to the product
members. Tighten bottom screws
securly. Tighten top screws (with
washer) snugly allowing for future
adjustment.
(See illustration 8)
Step 6
Add Dimension A and Dimension B
together. Measure this distance from
bottom of the inside of your cabinet
door and mark a horizontal line.
(See illustration 5). Measure center
point on inside of cabinet door and mark
this point as well.
A+B
Center
Dimension C
Equal
Equal
Step 10.
Be sure bumper pads are installed to all four
corners of door. Push door closed and apply
pressure to all four
corners making sure
door is flush with cabinet.
(See illustration 9).
Step 11.
Pulling from bottom,
pull door open.
(See illustration 10).
Securly tighten
top screws.
Step 12.
If your cabinet door is not straight
(even all around) you can adjust it
by loosing the screws on one of the
sides, properly align the cabinet
door and re-tighten the screws.
Helpful Hints:
There are several different
ways to mount the Door
Brackets to your cabinet
door ensuring that you
are mounting to the
thick portion of the door.
For instance, spacers can
be used when mounting Door Brackets to the
Product Members (spacer kit included). The Door
Bracket can also be installed on the inner side of the
Product Member.
Illustration 5
illustration 8
illustration 6
ilustration 7
If your door is parallel but slightly
off center. Loosen screws
that attach the slide mounting feet
to the cabinet floor, slide assembly
sideways as needed and re-tighten
screws.
2409 Plantside Drive
Jeffersontown, KY 40299
800-626-1126
502-491-2215 fax
illustration 9
illustration 10
Door...
off left
to right
Door...
crooked
all around
Door...
straight
after
ajustment
Door...
straight
after
ajustment
Door
Door
Door
I-RV-DM KIT
Face Frame
Mounting hole
locations
Dimension C
g. 5
g. 4
g. 1
g. 2
Face Frame
g. 3
Door
Cabinet
Floor
Dimension
A
Dimension
B
Paso 10: Asegúrese de instalar topes de amortiguación (no incluidos) en las cuatro
esquinas de la puerta. Cierre la puerta y presione las cuatro esquinas para
asegurarse de que la puerta esté a ras con el armario. (Ver la ilustración 8)
Étape 10: Veiller à ce que les quatre coins de la porte soient munis de coussinets
amortisseurs (non fournis). Fermer la porte et appuyer fermement sur les quatre
coins pour assurer que la porte est à aeurement de l’armoire. (Voir l’illustration 8)
Paso 11: Tire de la puerta por los costados y a la altura de las deslizaderas
para abrirla. (Ver la ilustración 9) Apriete bien los tornillos superiores.
Étape 11: Ouvrir la porte en tirant sur les côtés au niveau des glissières.
(Voir l’illustration 9). Bien serrer les vis du haut.
Paso 12: Para ajustar la puerta del armario si no está derecha
(emparejarla a todo su alrededor), debe aojar los tornillos en uno de los lados,
alinear bien la puerta y volver a apretar los tornillos.
Étape 12: Si la porte de l’armoire est de travers, desserrer les vis d’un côté, corriger
l’alignement de la porte et resserrer les vis.
Si la puerta está paralela pero ligeramente descentrada, aoje los tornillos que
sujetan las patas de las deslizaderas al piso del armario, mueva el ensamblaje lat-
eralmente según sea necesario y vuelva a apretar los tornillos.
Si la porte est parallèle mais légèrement décentrée, desserrer les vis xant les pattes
de l’ensemble de glissières au fond de l’armoire. Glisser l’ensemble vers le côté
jusqu’à ce que la position soit correcte et resserrer les vis.
Paso 9: Monte la puerta con los soportes instalados en los tornillos de
montaje en las placas del producto. Apriete bien los
tornillos de la parte inferior. Apriete los tornillos superiores (con las
arandelas) pero de modo que le permite realizar ajustes más adelante.
(Ver la ilustración 7)
Étape 9: Suspendre la porte avec les
supports aux vis de montage du produit. Fermement serrer les vis du
bas. Bien serrer les vis du haut (avec les rondelles) en
laissant un peu de jeu pour des réglages futurs. (Voir l’illustration 7)
12400 Earl Jones Way • Louisville, KY 40299
[phone] • www.rev-a-shelf.com
Paso 8: Retire los soportes de puerta de las placas del producto y atorníllelos en
el interior de la puerta del armario con tornillos de cabeza plana núm. 6 x 1/2 pulg.
Nota: Coloque los soportes de puerta sobre las líneas verticales y horizontales que
ha dibujado en los pasos 2 y 3 para alinearlos. (Ver la ilustración 6)
Étape
8: Enlever les supports de porte du produit et visser sur l’intérieur de la
porte d’armoire avec des vis à tête plate no 6 x 1/2 po. REMARQUE. Aligner le
support de porte sur la porte en l’alignant sur les lignes verticale et horizontale
tirées aux étapes 2 et 3. (Voir l’illustration 6)
Step 7
Take Dimension C (from Step 4)
and divide it by two. Measure this
distance to the left of the center point
on the inside of the cabinet door and make a
vertical line. Measure this
distance to the right of the center
point on the inside of the cabinet
door and make another vertical line
(See illustration 6)
Step 8
Remove Door Brackets from product
members and screw to inside of cabinet
door with #6 x 1/2'' flat head screws.
NOTE: Line up door bracket to cabinet door
by aligning door bracket with the vertical and
horizontal lines you have marked in Steps 6
& 7.
(See illustration7)
Step 9
Hang door with brackets attached on
the mounting screws on to the product
members. Tighten bottom screws
securly. Tighten top screws (with
washer) snugly allowing for future
adjustment.
(See illustration 8)
Step 6
Add Dimension A and Dimension B
together. Measure this distance from
bottom of the inside of your cabinet
door and mark a horizontal line.
(See illustration 5). Measure center
point on inside of cabinet door and mark
this point as well.
A+B
Center
Dimension C
Equal
Equal
Step 10.
Be sure bumper pads are installed to all four
corners of door. Push door closed and apply
pressure to all four
corners making sure
door is flush with cabinet.
(See illustration 9).
Step 11.
Pulling from bottom,
pull door open.
(See illustration 10).
Securly tighten
top screws.
Step 12.
If your cabinet door is not straight
(even all around) you can adjust it
by loosing the screws on one of the
sides, properly align the cabinet
door and re-tighten the screws.
Helpful Hints:
There are several different
ways to mount the Door
Brackets to your cabinet
door ensuring that you
are mounting to the
thick portion of the door.
For instance, spacers can
be used when mounting Door Brackets
to the
Product Members (spacer kit included). The Door
Bracket can also be installed on the inner side of the
Product Member.
Illustration 5
illustration 8
illustration 6
ilustration 7
If your door is parallel but slightly
off center. Loosen screws
that attach the slide mounting feet
to the cabinet floor, slide assembly
sideways as needed and re-tighten
screws.
2409 Plantside Drive
Jeffersontown, KY 40299
800-626-1126
502-491-2215 fax
illustration 9
illustration 10
Door...
off left
to right
Door...
crooked
all around
Door...
straight
after
ajustment
Door...
straight
after
ajustment
Door
Door
Door
I-RV-DM KIT
STEP 5:
Peel off the exterior layer of tape.
Now carefully line up your desired
door position by eyesight using
the drawer above and any cabinets
to your left or right as a gauge for
correct alignment.
STEP 6:
Press the door firmly onto the
door brackets with the two sided
tape. Put pressure directly on the
lower left and right edge to allow
for good adhesion.
ALTERNATIVE “EASY INSTALL”
for RV Series Pull-Out Waste Containers WITH
Door Mounting Brackets Tape
Your Door Mount Kit also includes two pieces of specially designed two-sided tape. Follow the directions below for quick and easy installation
method that is usually much faster for “In-Home” retro-fitting:
STEP 1:
Follow steps one through four on “Installation
Instructions” (Seperate Sheet).
STEP 3:
Peel off one side of each of the (4) tape squares provided and
carefully place over the door bracket flanges
STEP 2:
Make sure you have correctly
selected the correct positioning of
our Door Bracket Flanges so that
the mounting holes will be located
in a position to insert the fastners
(screws) in the thick, outside
section of the door panel.
STEP 4:
Loosen the 4 bolts (2 each side) that connect the door brackets to
the product member bracket. Pull them forward (towards you) and
tighten them. This will insure that the face of the door bracket
extends slightly outside of the front frame of your cabinet.
STEP 9:
• Final adjustment
• Loosen the four bolts and make adjustments if necessary.
(See Step 12 on installation instructions)
STEP 7:
Carefully pull out door from bottom edge and mark
several holes on each side through the brackets.
STEP 8:
Fasten the brackets to the door
using the tape as a temporary hold
while you insert your #6 x 1/2"
wood screws.
2409 Plantside Drive • Jeffersontown, KY 40299
800-626-1126 • 502-491-2215 fax
www.rev-a-shelf.com
I-RV-DM-KIT-E 4-02
g. 6
g. 7
g. 9
g. 8
I-4WBM-RM 02/09
Paso 7: Tome la Dimensión C del Paso 4 y divídala entre 2. Mida esta
distancia a la izquierda del punto central en el interior de la puerta de
gabinete y haga una línea vertical. Mida esta distancia a la derecha del
punto central en el interior de la puerta del gabinete y haga otra línea
vertical. (Ver gura 5)
Étape 7. Prenez la dimension C de l’étape 4 et divisez-la par deux.
Mesurez cette distance à la gauche du point central sur l’intérieur de la
porte du caisson et marquez une ligne verticale. Mesurez cette distance
à la droite du point central sur l’intérieur de la porte de coret et
marquez une autre ligne verticale. (Voir la gure 5)
Step 7
Take Dimension C (from Step 4)
and divide it by two. Measure this
distance to the left of the center point
on the inside of the cabinet door and make a
vertical line. Measure this
distance to the right of the center
point on the inside of the cabinet
door and make another vertical line
(See illustration 6)
Step 8
Remove Door Brackets from product
members and screw to inside of cabinet
door with #6 x 1/2'' flat head screws.
NOTE: Line up door bracket to cabinet door
by aligning door bracket with the vertical and
horizontal lines you have marked in Steps 6
& 7.
(See illustration7)
Step 9
Hang door with brackets attached on
the mounting screws on to the product
members. Tighten bottom screws
securly. Tighten top screws (with
washer) snugly allowing for future
adjustment.
(See illustration 8)
Step 6
Add Dimension A and Dimension B
together. Measure this distance from
bottom of the inside of your cabinet
door and mark a horizontal line.
(See illustration 5). Measure center
point on inside of cabinet door and mark
this point as well.
A+B
Center
Dimension C
Equal
Equal
Step 10.
Be sure bumper pads are installed to all four
corners of door. Push door closed and apply
pressure to all four
corners making sure
door is flush with cabinet.
(See illustration 9).
Step 11.
Pulling from bottom,
pull door open.
(See illustration 10).
Securly tighten
top screws.
Step 12.
If your cabinet door is not straight
(even all around) you can adjust it
by loosing the screws on one of the
sides, properly align the cabinet
door and re-tighten the screws.
Helpful Hints:
There are several different
ways to mount the Door
Brackets to your cabinet
door ensuring that you
are mounting to the
thick portion of the door.
For instance, spacers can
be used when mounting Door Brackets to the
Product Members (spacer kit included). The Door
Bracket can also be installed on the inner side of the
Product Member.
Illustration 5
illustration 8
illustration 6
ilustration 7
If your door is parallel but slightly
off center. Loosen screws
that attach the slide mounting feet
to the cabinet floor, slide assembly
sideways as needed and re-tighten
screws.
2409 Plantside Drive
Jeffersontown, KY 40299
800-626-1126
502-491-2215 fax
illustration 9
illustration 10
Door...
off left
to right
Door...
crooked
all around
Door...
straight
after
ajustment
Door...
straight
after
ajustment
Door
Door
Door
I-RV-DM KIT
g. 5
Puerta
Porte
Dimensión C
Door Mount
Bracket
Product
Member