Instructions / Assembly

INSTALLATION INSTRUCTIONS: DOUBLE 30QT WASTE CONTAINER WITH BLUM SOFT-CLOSE
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
4WC DOUBLE 30QT WASTE CONTAINER WITH BLUM
®
SOFT-CLOSE
TOOLS REQUIRED:
15 MIN
ESTIMATED ASSEMBLY TIME:
CARE AND MAINTENANCE:
Clean with a damp cloth and
wipe parts dry.
STEP 1
To assemble the slides, attach
the cross bar into the feet as
shown in Fig 1.1.
Attach the left and right slides
respectively to the top of
the feet. You will hear/feel
a “Snap” when connected
completely. See Fig 1.2.
Once slides are assembled, set
them to the side.
For video instruction visit:
rev-a-shelf.com/videos
#2
3
32
I-4WC-24DM2-SC-0217
FIGURE 1.1 FIGURE 1.2
Remove the slide triggers from
their wrapping.
Turn your waste container
chassis over and locate the pre-
drilled holes on the front lip of
the box. Refer to Figure 2.1
for help locating.
Using the provided screws,
attach the left and right sided
triggers (See Figure 2.2) and
set the waste container chassis
to the side.
NOTE:
Release triggers are side
sensitive and are marked
with an “L” & “R” for Left
and Right.
STEP 2
Place template into cabinet
and position front edge to
where the back of your door
will be when closed.
Inset door = set back the
thickness of your door
Overlay door = place at the
front edge of cabinet
Using an awl or pencil, mark
through the bold dotted screw
locations onto your cabinet
oor. Remove template when
done. Using your 3/32” drill
bit, pre-drill your cabinet oor
in all 8 locations being sure to
NOT drill through the cabinet
oor completely.
Lay your assembled slide set
over the top of the marked
holes. Using the 8 screws
provided, attach the slides to
the cabinet oor through the
grey slide feet holes.
Place your 4WC wood box with
attached triggers on top of the
slides and push back until you
hear the “Click” sound.
STEP 3
Customer Service: 800-626-1126 | rev-a-shelf.com
Pre-drilled holes
Slide triggers
Edge of paper to
back of door
Center line of
cabinet opening
Fold here to t Cabinet
1) Place template into cabinet and position front edge to where the back of
your door will be
a. Inset door = set back the thickness of your door
b. Overlay = place at the front edge of cabinet
2) Using an awl or pencil, mark through the bold dotted screw locations onto
your cabinet oor. Remove template when done
3) Lay your assembled slide set over the top of the marked holes and using the
provided 8 screws, attach the slides to the cabinet oor through the grey
slide feet holes
4) Place your Waste Container chassis with attached triggers on top of the
slides and push back until you hear the “click” sound. You are now ready to
insert the waste receptacles into the chassis.
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
DOUBLE 30QT WASTE CONTAINER W/ BLUM SOFT-CLOSE TEMPLATE
T-4WCBM2430SC-TRI-0116
#2
#2
3
32
BY DATE
DRAWN
DRAWING NO. SCALE
MATERIAL
FINISH
PART NO. SHEET OF
This drawing is the property of Rev-A-Shelf (RAS) and is disclosed
in confidence to the extent its subject matter is original to RAS. Any
vendor receiving this drawing from RAS shall hold and use this drawing
for the sole benefit of RAS and shall not disclose it to, or use or
reproduce it for any third party, or perform any act adverse to the interest
of RAS with respect to this drawing without the express written permission
of RAS. Vendors shall not revise any physical, dimensional or
performance characteristic unless authorized by Rev-A-Shelf Engineering.
TOLERANCES
MAT. DEC. ANGLES
(WOOD) .XX .03 [.8mm] 1/2
(OTHER) .XX .02 [.5mm]
(ALL) .XXX .005 [.13 mm]
FRACTIONS 1/32 [.8 mm]
SIZE
B
INCH
[MM]
AMERICAN
PROJECTION
1 2
CUSTOMER DRAWING
20.97
[532,64]
19.62
[498,3]
9.82
[249,3]
5.00
[127]
23.00
[584,3]
21.63
[549,3]
20.25
[514,4]
21.87
[555,6]
REV. DATE BY DESCRIPTION OF CHANGE
DOUBLE 30 QUART WASTE
CONTAINER BLUM SOFT CLOSE
BKT 7/30/15
0.100 4WCSC-2430DM-2
4WCSC-2430DM-2
Note: The ideal distance between
bracket screws should
be 21-5/8”, allowing for
maximum adjustability.
23“
21-5/8“
21-1/4“
9-13/16“
5“
FIGURE 2.1 FIGURE 2.2