Installation Sheet

ManualsBrandsRev-A-Shelf ManualsShop All Rev-A-ShelfRev-A-Shelf 4WTCD Series Two-Tiered Cutlery Drawer for 30" Base Cabinet

INSTALLATION INSTRUCTIONS: WOOD TWO–TIERED DRAWER

12400 Earl Jones Way

Louisville, KY 40299

rev-a-shelf.com

Customer Service: 800-626-1126

WOOD TWO–TIERED DRAWER

TOOLS REQUIRED:

20 MIN

ESTIMATED ASSEMBLY TIME:

CARE AND MAINTENANCE:

Clean with a damp cloth and

wipe parts dry.

NOTE:

The wood two–tiered drawer

is designed to use either

BLUMOTION 563F5330B

under mount slides or Grass

Elite 7523-19/550/533 under

mount slides.

4WTCD-30 & 4WTCD-36 with

BLUMOTION slides require an

additional stabilizer bar which

is included in the kit purchase.

I-4WTCD-TRI-0116

THE WOOD TWO–TIERED DRAWER (WTCD) IS DESIGNED

TO USE UNDER MOUNT FULL-EXTENSION DRAWER

HARDWARE ONLY. IF YOU ARE REPLACING A DRAWER

BOX THAT DOES NOT CURRENTLY USE FULL-EXTENSION

(FX) OR PREMIUM GUIDE (PG) HARDWARE YOU WILL

NEED TO ORDER A DRAWER GUIDE KIT (DGK).

4WTCD-15

4WTCD-343FLSC

4WTCD-18

4WTCD-419FL

4WTCD-30 4WTCD-36 4WTCD-18-KCUP

4WTCD-21

4WTCD-495FL

4WTCD-24

4WTCD-572FL

For video instruction visit:

rev-a-shelf.com/videos

JUST ADD

YOUR OWN

DRAWER

FRONT!

Summary of content (8 pages)

PAGE 1
2400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 WOOD TWO–TIERED DRAWER JUST ADD YOUR OWN DRAWER FRONT! TOOLS REQUIRED: #2 7 64 4WTCD-343FLSC 4WTCD-419FL 4WTCD-495FL 4WTCD-572FL 4WTCD-15 4WTCD-18 4WTCD-21 4WTCD-24 #2 ESTIMATED ASSEMBLY TIME: 20 MIN CARE AND MAINTENANCE: Clean with a damp cloth and wipe parts dry.
PAGE 2
STEP 1 Remove existing drawer box from cabinet by squeezing the drawer locking devices and pulling the drawer box forward. FIG. Bottom view 1 Using a pencil trace around the bottom two corners of the drawer and onto the back of the drawer front. Remove the screws that secure the drawer front to the drawer box. Also remove the two drawer locking devices by removing the two screws that secure each locking device to the bottom front edge of the drawer box. Discard the existing drawer box.
PAGE 3
STEP 3 Secure a Figure 8 fastener on each side of the drawer box front using the pre-drilled pilot hole as a locator. FIG. 3a Once the (2) Figure 8 fasteners have been secured to the drawer box place the drawer box on the back of the drawer front from Step one. Align the bottom (2) corners of the drawer box with the pencil marks. Drill a 7/64” dia. X 3/8” deep pilot hole through the middle of each fasterner and into the back of the front. Be careful to not drill through the drawer front.
PAGE 4
PAGE 5
12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.
PAGE 6
PASO 1 ÉTAPE1 Quite el cajón existente del gabinete, apretando los dispositivos de seguridad del cajón, y jalándolo hacia adelante. Usando un lápiz, trace alrededor de las esquinas de la parte inferior del cajón y hacia la parte posterior del frente del cajón. Quite los tornillos que aseguran la parte del frente del cajón hacia el cajón.
PAGE 7
PASO STEP 1 3 ÉTAPE 3 Asegure el cierre de la figura 8 a cada lado de la parte frontal del cajón, usando los orificios pre taladrados como punto de referencia. Una vez que los dos cierres de la figura 8 estén asegurados a la caja, coloque la caja en la parte posterior del cajón del paso número 1. FIG. 3A Alinee las dos esquinas inferiores de la caja con las marcas del lápiz.
PAGE 8
PASO 3 ÉTAPE 3 Coloque el Cajón de Madera de Dos Niveles (WTCD por sus siglas en inglés) con el frente del cajón sujeto dentro del gabinete, deslizando la caja dentro del sistema hasta que el gancho engrane con los orificios taladrados en la parte trasera del cajón. Usted escuchará un chasquido cuando el cajón y el sistema estén completamente engranados. Usted podría necesitar apretar los dispositivos de liberación de seguridad y empujarlos hacia atrás para asegurar que el sistema esté engranado. FIG.