Installation Guide

SYSTEM 9
ADJUSTMENT
INSTRUCTIONS
TO ADJUST DOOR HEIGHT
Shipping pins must be removed before atempting
height adjustment. You will need to use pliers.
Rotate the doors to the right, exposing the height
adjustment screw.
TO ADJUST DOOR CLOSING ALIGNMENT
Open the doors so that one side of the bottom
mounting bracket can be seen.
Remove the shipping screw and loosen the star-
washer screw. If the door is out of alignment to
the left insert shipping screw into the right side of
the slot as shown. Reverse if alignment is out to
the right. Repeat on both sides of bottom mount-
ing bracket.
Rotate bracket to the left or right depending which
way the doors should go.
Turn the screw to the right to raise the doors and
turn to left to lower the doors.
*Trays do not need to be unloaded to adjust (up to 100 lbs.)
Tighten the door alignment screws and close the
door to check alignment. Repeat if necessary.
TO ADJUST FOR SIDE/SIDE CLEARANCE
Remove shipping screws. Loosen the front and
back (star-washer) screws.
Adjust mounting bracket to correct the gap between
the sides of the door and frame at the top.
TOP ADJUSTEMENT
Tighten, check and repeat if necessary..Re-insert
shipping screw in any unused hole or slot.
Remove shipping screws. If you have not already
done so. Loosen (star-washer) screws.
Adjust mounting bracket to correct the gap
between the sides of the door and frame at the
bottom.
BOTTOM ADJUSTMENT
Tighten, check and repeat if necessary.
REMOVAL of the Lazy Daisy® Susan Unit
In the unlikely event that the entire Lazy Daisy
Susan. Unit must be removed, please follow
these instructions.
1. Detach doors from both the top and bottom
trays.
2. Remove the shipping pins from above
the top tray.
3. Lift bottom tray and remove bottom tray
securing pin.
4. Lift top tray and remove top tray securing pin.
5. Remove screws from top mounting bracket.
6. Lift both trays to the middle of the cabinet. Tilt
the tube and remove top mounting bracket.
7. Tilt bottom of the tube and remove brake pivot
post.
8. Rotate trays so that complete unit can be
removed from cabinet.
9. Remove trays from tube.
10. Remove bottom mounting bracket.
SYSTEM 9 PIE-CUT PARTS DRAWING
________________________________________
_____________________________________
________________________________________
CARE INSTRUCTIONS: Wipe clean with soft cloth and mild, non-abrasive detergent or soap solution. Avoid scoring pads, etc.
1.
2.
3.
1.
2.
3.
4.
1.
2.
1.
2.
3.
3.
I-LD-3002
BY
SYSTEM 9
ADJUSTMENT
INSTRUCTIONS
TO ADJUST DOOR HEIGHT
Shipping pins must be removed before atempting
height adjustment. You will need to use pliers.
Rotate the doors to the right, exposing the height
adjustment screw.
TO ADJUST DOOR CLOSING ALIGNMENT
Open the doors so that one side of the bottom
mounting bracket can be seen.
Remove the shipping screw and loosen the star-
washer screw. If the door is out of alignment to
the left insert shipping screw into the right side of
the slot as shown. Reverse if alignment is out to
the right. Repeat on both sides of bottom mount-
ing bracket.
Rotate bracket to the left or right depending which
way the doors should go.
Turn the screw to the right to raise the doors and
turn to left to lower the doors.
*Trays do not need to be unloaded to adjust (up to 100 lbs.)
Tighten the door alignment screws and close the
door to check alignment. Repeat if necessary.
TO ADJUST FOR SIDE/SIDE CLEARANCE
Remove shipping screws. Loosen the front and
back (star-washer) screws.
Adjust mounting bracket to correct the gap between
the sides of the door and frame at the top.
TOP ADJUSTEMENT
Tighten, check and repeat if necessary..Re-insert
shipping screw in any unused hole or slot.
Remove shipping screws. If you have not already
done so. Loosen (star-washer) screws.
Adjust mounting bracket to correct the gap
between the sides of the door and frame at the
bottom.
BOTTOM ADJUSTMENT
Tighten, check and repeat if necessary.
REMOVAL of the Lazy Daisy® Susan Unit
In the unlikely event that the entire Lazy Daisy
Susan. Unit must be removed, please follow
these instructions.
1. Detach doors from both the top and bottom
trays.
2. Remove the shipping pins from above
the top tray.
3. Lift bottom tray and remove bottom tray
securing pin.
4. Lift top tray and remove top tray securing pin.
5. Remove screws from top mounting bracket.
6. Lift both trays to the middle of the cabinet. Tilt
the tube and remove top mounting bracket.
7. Tilt bottom of the tube and remove brake pivot
post.
8. Rotate trays so that complete unit can be
removed from cabinet.
9. Remove trays from tube.
10. Remove bottom mounting bracket.
SYSTEM 9 PIE-CUT PARTS DRAWING
________________________________________
_____________________________________
________________________________________
CARE INSTRUCTIONS: Wipe clean with soft cloth and mild, non-abrasive detergent or soap solution. Avoid scoring pads, etc.
1.
2.
3.
1.
2.
3.
4.
1.
2.
1.
2.
3.
3.
I-LD-3002
BY
SYSTEM 9
ADJUSTMENT
INSTRUCTIONS
TO ADJUST DOOR HEIGHT
Shipping pins must be removed before atempting
height adjustment. You will need to use pliers.
Rotate the doors to the right, exposing the height
adjustment screw.
TO ADJUST DOOR CLOSING ALIGNMENT
Open the doors so that one side of the bottom
mounting bracket can be seen.
Remove the shipping screw and loosen the star-
washer screw. If the door is out of alignment to
the left insert shipping screw into the right side of
the slot as shown. Reverse if alignment is out to
the right. Repeat on both sides of bottom mount-
ing bracket.
Rotate bracket to the left or right depending which
way the doors should go.
Turn the screw to the right to raise the doors and
turn to left to lower the doors.
*Trays do not need to be unloaded to adjust (up to 100 lbs.)
Tighten the door alignment screws and close the
door to check alignment. Repeat if necessary.
TO ADJUST FOR SIDE/SIDE CLEARANCE
Remove shipping screws. Loosen the front and
back (star-washer) screws.
Adjust mounting bracket to correct the gap between
the sides of the door and frame at the top.
TOP ADJUSTEMENT
Tighten, check and repeat if necessary..Re-insert
shipping screw in any unused hole or slot.
Remove shipping screws. If you have not already
done so. Loosen (star-washer) screws.
Adjust mounting bracket to correct the gap
between the sides of the door and frame at the
bottom.
BOTTOM ADJUSTMENT
Tighten, check and repeat if necessary.
REMOVAL of the Lazy Daisy® Susan Unit
In the unlikely event that the entire Lazy Daisy
Susan. Unit must be removed, please follow
these instructions.
1. Detach doors from both the top and bottom
trays.
2. Remove the shipping pins from above
the top tray.
3. Lift bottom tray and remove bottom tray
securing pin.
4. Lift top tray and remove top tray securing pin.
5. Remove screws from top mounting bracket.
6. Lift both trays to the middle of the cabinet. Tilt
the tube and remove top mounting bracket.
7. Tilt bottom of the tube and remove brake pivot
post.
8. Rotate trays so that complete unit can be
removed from cabinet.
9. Remove trays from tube.
10. Remove bottom mounting bracket.
SYSTEM 9 PIE-CUT PARTS DRAWING
________________________________________
_____________________________________
________________________________________
CARE INSTRUCTIONS: Wipe clean with soft cloth and mild, non-abrasive detergent or soap solution. Avoid scoring pads, etc.
1.
2.
3.
1.
2.
3.
4.
1.
2.
1.
2.
3.
3.
I-LD-3002
BY
SYSTEM 9
ADJUSTMENT
INSTRUCTIONS
TO ADJUST DOOR HEIGHT
Shipping pins must be removed before atempting
height adjustment. You will need to use pliers.
Rotate the doors to the right, exposing the height
adjustment screw.
TO ADJUST DOOR CLOSING ALIGNMENT
Open the doors so that one side of the bottom
mounting bracket can be seen.
Remove the shipping screw and loosen the star-
washer screw. If the door is out of alignment to
the left insert shipping screw into the right side of
the slot as shown. Reverse if alignment is out to
the right. Repeat on both sides of bottom mount-
ing bracket.
Rotate bracket to the left or right depending which
way the doors should go.
Turn the screw to the right to raise the doors and
turn to left to lower the doors.
*Trays do not need to be unloaded to adjust (up to 100 lbs.)
Tighten the door alignment screws and close the
door to check alignment. Repeat if necessary.
TO ADJUST FOR SIDE/SIDE CLEARANCE
Remove shipping screws. Loosen the front and
back (star-washer) screws.
Adjust mounting bracket to correct the gap between
the sides of the door and frame at the top.
TOP ADJUSTEMENT
Tighten, check and repeat if necessary..Re-insert
shipping screw in any unused hole or slot.
Remove shipping screws. If you have not already
done so. Loosen (star-washer) screws.
Adjust mounting bracket to correct the gap
between the sides of the door and frame at the
bottom.
BOTTOM ADJUSTMENT
Tighten, check and repeat if necessary.
REMOVAL of the Lazy Daisy® Susan Unit
In the unlikely event that the entire Lazy Daisy
Susan. Unit must be removed, please follow
these instructions.
1. Detach doors from both the top and bottom
trays.
2. Remove the shipping pins from above
the top tray.
3. Lift bottom tray and remove bottom tray
securing pin.
4. Lift top tray and remove top tray securing pin.
5. Remove screws from top mounting bracket.
6. Lift both trays to the middle of the cabinet. Tilt
the tube and remove top mounting bracket.
7. Tilt bottom of the tube and remove brake pivot
post.
8. Rotate trays so that complete unit can be
removed from cabinet.
9. Remove trays from tube.
10. Remove bottom mounting bracket.
SYSTEM 9 PIE-CUT PARTS DRAWING
________________________________________
_____________________________________
________________________________________
CARE INSTRUCTIONS: Wipe clean with soft cloth and mild, non-abrasive detergent or soap solution. Avoid scoring pads, etc.
1.
2.
3.
1.
2.
3.
4.
1.
2.
1.
2.
3.
3.
I-LD-3002
BY
SYSTEM 9
ADJUSTMENT
INSTRUCTIONS
TO ADJUST DOOR HEIGHT
Shipping pins must be removed before atempting
height adjustment. You will need to use pliers.
Rotate the doors to the right, exposing the height
adjustment screw.
TO ADJUST DOOR CLOSING ALIGNMENT
Open the doors so that one side of the bottom
mounting bracket can be seen.
Remove the shipping screw and loosen the star-
washer screw. If the door is out of alignment to
the left insert shipping screw into the right side of
the slot as shown. Reverse if alignment is out to
the right. Repeat on both sides of bottom mount-
ing bracket.
Rotate bracket to the left or right depending which
way the doors should go.
Turn the screw to the right to raise the doors and
turn to left to lower the doors.
*Trays do not need to be unloaded to adjust (up to 100 lbs.)
Tighten the door alignment screws and close the
door to check alignment. Repeat if necessary.
TO ADJUST FOR SIDE/SIDE CLEARANCE
Remove shipping screws. Loosen the front and
back (star-washer) screws.
Adjust mounting bracket to correct the gap between
the sides of the door and frame at the top.
TOP ADJUSTEMENT
Tighten, check and repeat if necessary..Re-insert
shipping screw in any unused hole or slot.
Remove shipping screws. If you have not already
done so. Loosen (star-washer) screws.
Adjust mounting bracket to correct the gap
between the sides of the door and frame at the
bottom.
BOTTOM ADJUSTMENT
Tighten, check and repeat if necessary.
REMOVAL of the Lazy Daisy® Susan Unit
In the unlikely event that the entire Lazy Daisy
Susan. Unit must be removed, please follow
these instructions.
1. Detach doors from both the top and bottom
trays.
2. Remove the shipping pins from above
the top tray.
3. Lift bottom tray and remove bottom tray
securing pin.
4. Lift top tray and remove top tray securing pin.
5. Remove screws from top mounting bracket.
6. Lift both trays to the middle of the cabinet. Tilt
the tube and remove top mounting bracket.
7. Tilt bottom of the tube and remove brake pivot
post.
8. Rotate trays so that complete unit can be
removed from cabinet.
9. Remove trays from tube.
10. Remove bottom mounting bracket.
SYSTEM 9 PIE-CUT PARTS DRAWING
________________________________________
_____________________________________
________________________________________
CARE INSTRUCTIONS: Wipe clean with soft cloth and mild, non-abrasive detergent or soap solution. Avoid scoring pads, etc.
1.
2.
3.
1.
2.
3.
4.
1.
2.
1.
2.
3.
3.
I-LD-3002
BY