Installation Guide

ManualsBrandsRev-A-Shelf ManualsKitchen Appliance5 in. H x 5 in. W x 5 in. D Full Height Base Cabinet Heavy Duty Mixer Lift

2409 Plantside Drive

Jeffersontown, KY 40299

Customer Service: 800-626-1126

www.rev-a-shelf.com

Mixer Lift Instructions

RAS-ML-HDCR

I-ML-HDCR-0113

Step 1 - Installing Side Support Panels for Face Frame Cabinets – See FIG. A,

(Support Panels not included) Align top of side panel with top of cabinet. Side panels should

be 6" high and run the total depth of the cabinet.The maximum thickness of the side panel

should equal the face frame overlay.The minimum thickness of the side panel should

allow for a 1/2" max recess.

FIG. A

1/2" MAX

RECOMMENDED

RECESS.

SUPPORT

PANEL

INSIDE OF

CABINET,

LOOKING

DOWN

FROM

THE TOP

SUPPORT PANEL

FURNISHED BY CONSUMER

WIDTH

– 6"

HGT

– FULL DEPTH OF CABINET

CABINET FRONT,

FACE FRAME

Step 2 - Installing Side Mounting Brackets - See FIG. B

Mark and Pre-drill two 3/32" pilot holes 1/2" deep into the

side support panel.The first hole should be 3/8" from inside of

face frame (front of cabinet on frameless cabinet), and 4-1/2"

down from the top of the cabinet).

The second hole is located parallel from the first hole location

11-3/8" towards rear of cabinet. Mount side mounting bracket to

cabinet side panel by aligning outside middle hole loc ations with

the holes that you have just pre-drilled. Fasten with 2 - #10 x 3/4"

wood screws. Fasten 6 additional #10 x 3/4" wood screws to additional

locations on side mount bracket. NOTE: Side mounting brackets

must be installed parallel with the top of the cabinet (level) for

proper function. Repeat this step for other side mounting bracket.

FIG. B

TO INSURE PROPER ALIGNMENT, USE

A LEVEL TO ESTABLISH THIS LINE

DRILL (2) – 3/32" PILOT HOLES

11-3/8"

(289 mm)

3/8"

(10 mm)

1-1/2" [38mm] COUNTER TOP

1-1/2" [38mm]

FACE RAIL

4-1/2"

(114 mm)

NOTE 2A

Distance from top of cabinet is determined by height and length of

accessory. 4-1/2" will allow adequate clearance for 6 qt. Kitchen Aid®

Stand Mixers. Side mounts can b e positioned higher if using lift for

smaller appliances.

W A R N I N G

This is a spring loaded

product and can cause

severe harm if not handled

properly during installation.

Summary of content (2 pages)

PAGE 1
FIG. A Mixer Lift Instructions RAS-ML-HDCR 2409 Plantside Drive Jeffersontown, KY 40299 Customer Service: 800-626-1126 www.rev-a-shelf.com Step 1 - Installing Side Support Panels for Face Frame Cabinets – See FIG. A, (Support Panels not included) Align top of side panel with top of cabinet. Side panels should be 6" high and run the total depth of the cabinet.The maximum thickness of the side panel should equal the face frame overlay.
PAGE 2
3/8" (10 mm) FIG. D 11-3/8" (289 mm) 1-1/2" (39 mm) FIG. C Step 3 - Adjusting Spring Tension – See FIG. C & D This heavy duty mixer lift is equipped 4-1/2" (115 mm) with three adjustable spring tension settings. 0-20, 20-30, and 30-60 lbs. This unit is shipped with the spring settings set to the middle setting. To adjust tension, remove set bolt with 10 mm open end wrench while holding tension on adjustment lever with 12 mm box end wrench.