Instructions / Assembly

ManualsBrandsRev-A-Shelf ManualsKitchen Appliance5 in. H x 5 in. W x 5 in. D Full Height Base Cabinet Heavy Duty Mixer Lift

A. QTY 16 #10 x 3/4” wood

screws

B. QTY 8 of the #10 x 1/2” wood

screws

C. Two side-mounting brackets

(left and right)

RAS-ML-HDSC-TRI-1115

*Mixer Lift shelf not included

This is a spring loaded

product and can cause

severe harm if not handled

properly during installation.

WARNING

TOOLS REQUIRED:

30–45 MIN

ESTIMATED ASSEMBLY TIME:

CARE AND MAINTENANCE:

• Clean with a damp cloth and

wipe parts dry

• Lubricate pivot points as

needed

12400 Earl Jones Way

Louisville, KY 40299

rev-a-shelf.com

Customer Service: 800-626-1126

HEAVY DUTY MIXER LIFT RAS-ML SERIES

FIGURE A

IF INSTALLING IN A FRAMELESS

CABINET, SKIP THIS AND MOVE

TO STEP 1

INSTALLING SIDE SUPPORT

PANELS FOR FACE FRAME

CABINETS

(Side Support Panels not included)

SEE FIGURE A

CABINET PREPARATION

A. B.

FACE FRAME OVERLAY

L: CABINET DEPTH

SIDE SUPPORT PANEL 1

LEFT

H: 8”

(204 mm)

PARTS LIST INCLUDED:

SIDE SUPPORT PANEL 2

RIGHT

PARTS LIST

INCLUDED:

X16

LEFT & RIGHT

VIDEO INSTRUCTIONS: WWW.REV-A-SHELF.COM/VIDEOS

Summary of content (8 pages)

PAGE 1
2400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 VIDEO INSTRUCTIONS: WWW.REV-A-SHELF.COM/VIDEOS HEAVY DUTY MIXER LIFT RAS-ML SERIES TOOLS REQUIRED: WARNING This is a spring loaded product and can cause severe harm if not handled properly during installation. 3 32 3 mm 10 mm 12 mm #2 ESTIMATED ASSEMBLY TIME: *Mixer Lift shelf not included PARTS LIST INCLUDED: A. B. 30–45 MIN X8 CARE AND MAINTENANCE: A. QTY 16 #10 x 3/4” wood screws B.
PAGE 2
STEP 1 INSTALLING SIDE MOUNTING BRACKETS SEE FIGURE B FIGURE B 1-1/2” (38 mm) COUNTER TOP 3 32 3 mm 1-1/2”(38 mm) COUNTERTOP #2 1-1/2”(38 mm) FACE RAIL TO INSURE PROPER ALIGNMENT, USE A LEVEL TO ESTABLISH THIS LINE 4-1/2” (114 mm) A. Mark and Pre-drill two 3/32” (3 mm) pilot holes 1/2” (13 mm) deep into the side support panel. B. The first hole should be 3/8” (10 mm) from inside of face frame (front of cabinet on frameless cabinet), and 4-1/2” (114 mm) down from the top of the cabinet.
PAGE 3
STEP 2 CON’T FIGURE D This unit is shipped with the spring set to the middle setting: 20–30 lbs. (9.07 kg–13.6 kg). A. To adjust tension, remove set bolt with 10 mm open end wrench while holding tension on adjustment lever with 12 mm box end wrench. This needs to be done on both side-mounting brackets. TENSION ADJUSTMENT B. IMPORTANT NOTE DO NOT release holding tension until after the set bolt is in the desired location. With bolt removed, adjust to desired setting.
PAGE 4
STEP 4 MOUNTING MIXER LIFT SHELF SEE FIGURE E UNDERSIDE OF MIXER LIFT SHELF FIGURE F NOTE Pre-drilling first four hole locations will ensure proper function of mixer lift. A. Mark hole locations for the front screws by measuring in 3/4” (19 mm) from the side of the shelf and 8-1/4” (209 mm) from the front edge of the shelf. Mark rear screw locations by measuring up 7-1/2” (190mm) from the first set of marks. LAYOUT AND DRILL (4) 3/32” (3 mm) HOLES 7-1/2” (191 mm) B.
PAGE 5
12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com 800-626-1126 INSTRUCCIONES DE INSTALACIÓN / LES INSTRUCTIONS D’INSTALLATION ELEVADOR DE BATIDORA DE TRABAJO PESADO SERIES RAS-ML SÉRIES RAS-ML DU SYSTÈME ESCAMOTABLE DE MIXEUR ROBUSTE Herramientas requeridas: Outils Requis: / AVERTISSEMENT: Precaución: este es un producto que tiene resortes y puede causar daño severo si no se maneja con cuidado durante el proceso de instalación.
PAGE 6
1 Instalando soportes de montaje laterales. Installer les Supports de Montage Latéraux FIG. B B 3 32 1-1/2” (38 mm) Parte superior de la barra DESSUS DU COMPTOIR 3 mm #2 1-1/2”(38 mm) Para asegurar una alineación adecuada, utilice una niveladora para establecer esta línea. Pour assurer un bon alignement, utilisez un niveau pour établir cette ligne A. Marque y pre taladre dos orificios piloto de 3/32” (3 mm) de profundidad dentro del panel lateral de soporte.
PAGE 7
Esta unidad es enviada con un juego de resortes para la posición media de 20-30 libras (9.07 kg–13.6 kg). Cette unité est livrée avec le ressort réglé à la position du milieu, 20-30 lbs. (9,07 kg 13,6 kg). A. Para ajustar la tensión, quite el juego de pernos con una llave abierta de 10 mm mientras sostiene la tensión en el nivel de ajuste con una llave de caja de 12 mm. Esto tiene que hacerse en ambos lados de los soportes del montaje.
PAGE 8
4 F Montando la repisa para el elevador de la batidora FIG E NOTA Pre taladrando primero cuatro orificios de ubicación asegurará un funcionamiento adecuado de la función para el elevador de la la batidora. Parte inferior de la repisa del elevador de la batidora Dessous de la tablette du Système Escamotable de Mixeur Montage de la Tablette du Système Escamotable de Mixeur FIG E NOTE Pré-percer les quatre premiers emplacements des trous pour assurer le bon fonctionnement du système escamotable de mixeur.