Instruction Sheet

IMPORTANT SAFETY INSTRUCTIONS
• Use only in dry locations. Not for use where exposed to the weather.
• Replace the batteries on the Remote Control with (2) AAA batteries
only (non-rechargeable).
• Clean with a damp cloth. Do not use cleaners or detergents.
Page 2
Save these instructions for future reference.
For technical assistance, call 1-800-227-1171
Tresco Lighting by Rev-A-Shelf
12400 Earl Jones Way
Louisville, KY 40299
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web: www.trescolighting.com
I-RGBCCTRMT-0720
Signal Interference:
Outside interference may affect the signal between the Remote
Control and Parent Controller or Child Receiver. Typical items that
might cause interference include: metal pots and pans, leaded
glass, aluminum framed doors, etc. If experiencing interference,
try repositioning the Parent Controller or Child Receiver in
6” (15cm) increments. This typically allows the system to function
properly.
2
1
Each Remote Control can control up to 2 Parent Controllers
Note: Each zone can handle 1 Parent Controller and up to 10 Child Receivers.
#
2
RoHS
COMPLIANT
Instructions
FREEDiM Dynamic RF Remote Control
For RGB & CCT LEDs • 12VDC 60W & 24VDC 96W
The Built-In 10 Color-changing Modes are as follows:
Mode 1: Randomly selects any two colors of RGB mix fade-in & fade-out
Mode 2: RGB three colors mix fade-in & fade-out
Mode 3: RGB three colors mix fade-out & fade-in
Mode 4: RGB ash
Mode 5: RGB three colors fade-in & fade-out successively
Mode 6: RGB three colors fade-in successively
Mode 7: RGB three colors fade-out successively
Mode 8: RGB three colors jump changing successively
Mode 9: R&B two colors mix fade (R in B out), then G fade-in, then R&B
mix fade (R out B in), then G fade-out
Mode 10: B fade-out, then G&B mix fade (G out B in), then R&G mix fade
(R out G in), then R fade-in
10 Pre-programmed, RGB Color-Changing Modes:
Parent Controllers are pre-loaded with ten different programs to quickly
change lighting specications when needed. The ten programs are for
the RGB mode only and include: RGB color mixes, ashing, fade-in/
fade-out, etc. These pre-loaded programs are only accessible through
the Remote Control.
To Access and Review the 10 Pre-programmed Modes:
1. On the Remote Control (in RGB mode), press the Play button
R
G
B
Z1
Z2
3000K
3500K
5000K
once
to play the rst Preset Mode (see list below). Press the Play button
again to stop it. Press the Play button once again to advance to the
next preset mode.
2. Press the Speed-up button
R
G
B
Z1
Z2
3000K
3500K
5000K
to increase the speed of the mode (e.g.
faster fade-in/fade-out).
3. Press the Speed-down button
R
G
B
Z1
Z2
3000K
3500K
5000K
to decrease the speed.
To Deprogram the Remote Control:
1. Press and hold the Learning button on the Parent Controller. This will
erase all programming on the Remote Controls.
(Note: you cannot erase just one Remote Control at a time.)
Additional Information on Button Functions:
CCT Slider and RGB Color Wheel
- In CCT mode, you can quickly make adjustments with the CCT Slider
on top of the unit.
- In RGB mode, you can quickly make adjustments with the large RGB
Color Wheel.
- The RGB Color Wheel will not work in CCT mode, and the CCT Slider will
not work in RGB mode.
To check current settings, view the Parent Controller’s digital screen.
RGB and CCT Quick Preset Buttons:
The RGB/CCT Preset buttons are dual-purpose:
In RGB mode, the (3) Preset buttons quickly go to preset Red, Green or Blue
colors. Then the buttons work by turning on/off R, G or B. For example,
press R if you want solid red. Press R again to turn red off. If you then
want a mix of red and blue, press R and B.
In CCT mode, the (3) Preset buttons quickly go to preset Warm (3000K),
Neutral (3500K), or Cool (5000K) light. As in RGB mode, turn on/off the
Quick Preset buttons to achieve other warm/cool lighting effects.
Zone 1 and Zone 2 Buttons
- The FREEDiM Remote Control can control up to 2 zones independently.
(also see Fig. 2 below)
- The Remote Control cannot control both zones at once. Each zone must
be controlled independently.
- The Remote Control can have one zone in RGB mode and the other zone
in CCT mode to control two different Parent Controllers, but any single
Parent Controller can only be in RGB or CCT mode.
- To turn off a zone press and hold either the Zone 1 or Zone 2 button.
Switch Mode Button
- When the Remote Control is in RGB mode, the small indicator light
under the Switch Mode button
R
G
B
Z1
Z2
3000K
3500K
5000K
is red (see Fig. 1, on page 1).
- When in CCT mode, there is no indicator light.