Revel ® M10 Owner’s Manual
® ™ Revel Concerta M10 Owner’s Manual Table of Contents 3 Introduction 4 Planning Your System 4 Placement 4 Installation 5 Tabletop/Shelf Placement Assembly 8 Wall-Mounting the M10, Using the Included Wall Bracket 9 Wiring the Speaker 9 Maintenance and Service 10 Specifications 2
Introduction Revel® Concerta™ M10 The Revel® Concerta™ M10 satellite speaker continues the longstanding Revel commitment to accurate sound reproduction. The proprietary transducers utilizing Micro Ceramic Composite (MCC) diaphragms, precision dividing networks, sophisticated high-frequency waveguides and rigid enclosures all combine to deliver uncompromising performance in any stereo or multichannel home theater system.
Planning Your System Placement Before deciding where to best place your speakers, survey your room and study Figures 1 and 2. Note: The satellite speakers can be placed directly on a shelf or tabletop, using one of the three included shelf stands, or mounted on a wall using the included wall brackets. Optional floor stands are also available. Please contact your dealer.
Tabletop/Shelf Placement Assembly Step One Choose one of the three shelf stands on which to mount the satellite. If you decide to place the stand next to a television, the television’s height should be taken into consideration. If you choose the shortest stand, follow steps two to four on page 6. If you choose either of the taller stands, follow steps two to five on page 7.
Step Two Step Three For Small Table Stand Assembly Using the included Allen wrench, remove the bottom end cap of the speaker by unscrewing the single center screw on the bottom. For Small Table Stand Assembly Assemble the table stand plate, the small section and the foot. Place three nuts (provided) in the base of the foot and secure them in place by inserting three screws (provided) through the top of the table stand plate.
Step Two Step Four For Medium and Large Table Stand Assembly Using the included Allen wrench, remove the bottom end cap of the loudspeaker by unscrewing the single center screw on the bottom. For Medium and Large Table Stand Assembly Use the screw and washer to attach the medium or large base assembly to the speaker assembly, as shown.
Wall-Mounting the M10 Step Four Using the Included Wall Bracket Using the included Allen wrench, remove the bottom end cap of the speaker by unscrewing the single center screw on bottom. The customer is responsible for the proper selection and use of mounting hardware, and for correctly and safely wall-mounting the speakers. End cap Step One Remove the wall-bracket cover by removing the four wall bracket screws on the ends, as shown.
Step Six The wall-bracket design allows for rotation of the speakers at angles up to 30º of center. Position the speakers so that they face toward the primary listening position, before fully tightening. – + Figure 3: This example shows how to connect bare wires to the terminals. Banana plugs may also be inserted directly into the rear of the connector. Wiring the Speaker After placing the speaker, you are ready to connect it to your system. First, turn off all audio-system power.
Specifications Revel® Concerta™ M10 Frequency Response (±3dB) 110Hz – 21kHz Recommended Amplifier Power Range 10 – 150 Watts Sensitivity (2.83V @ 1m, 2π anechoic) 89dB Nominal Impedance 8 Ohms Crossover Frequency 2-1/2-Way high-order at 400Hz and 2.
Limited Warranty A valid serial number is required for warranty coverage. This Revel warranty protects the original retail purchaser for a period of five (5) years (parts and labor) from any failure as a result of original manufacturing defects, so long as: Customer Service will pay return shipping charges within the United States only in the event that the product is found to be defective, as mentioned above. There are other stipulations that may apply to shipping charges. 1.
Revel, the Revel logo and Concerta are trademarks of Harman International Industries, Incorporated, in the United States and/or other countries. Dolby and Pro Logic are registered trademarks of Dolby Laboratories. DTS is a registered trademark of DTS, Inc. Features, specifications and appearance are subject to change without notice. www.revelspeakers.com 250 Crossways Park Drive, Woodbury, NY 11797 8500 Balboa Boulevard, Northridge, CA 91329 516.594.0300 Technical Support: 516.682.3744 Part No.
