Operating Manual USER'S INSTRUCTIONS Model No.: RETRT2812-1 (DC 12V /AC 24V ~ 60HZ, 12W / NTSC) REVO AMERICA 700 FREEPORT PARKWAY SUITE 100 COPPELL, TX 75019 U.S.A. TEL.
USER’S MANUAL 2
USER’S MANUAL Contents • General Features 4 • Installing & Adjusting 5 • Dimension & Specification 6 • OSD Control Button 7 • Camera Menu Set Up 1. Menu Set Up 8 2. Lens Setting 8 3. Exposure Setting 9 4. White Balance Setting 10 5. SSDR Setting 11 6. Backlight Setting 12 7. DNR3 Setting 13 8. Day/Night Setting 14 9. Special Setting 15 10.
USER’S MANUAL General Features • Ultra High Sensitivity - The built-in high sensitivity COLOR CCD produces a clear image even in 0Lux(B/W, IR-LED ON) or lower illumination. • 600TV Lines - By adopting a diagonal 2.8mm(1/3") 410,000 (NTSC) pixel, 470,000(PAL) pixel SONY CCD, the camera produces clear picture quality with a horizontal resolution of 600 TV lines for color and a horizontal resolution of 700TV lines for BW mode.
USER’S MANUAL INSTALLING & ADJUSTING 1. Installation - Place the mounting plate on a flat installation surface and mount with the provided screws. - Feed the cable through the center of the mounting plate. - Place the camera body in the mounting plate socket and hold. - Then place the outer plate over the camera body & mounting plate and tighten side screws to lock the camera into place. - Loosen side screws to adjust camera angle as needed, then tighten the side screws to lock into place. 2.
USER’S MANUAL DIMENSION & SPECIFICATION 1. Dimension & Connection Dimension Connection 140mm 2.
USER’S MANUAL OSD Control Button 1. OSD button could be used when it needs to OSD control. ▲ Up button: Moves the cursor upwards. Use this button to select an item or adjust the parameters. ▼ Down button: Moves the cursor downwards. Use this button to select an item or adjust the parameters. • Left button: Moves the cursor to the left. Use this button to select or adjust the parameters of the selected item. The parameter changes each time this button is pressed.
USER’S MANUAL ● Menu Setup 1. Press the Function Setup switch. - Main setup menu is displayed on the monitor screen. MA N SETUP 1 LENS 2 EXPOSURE 3 WH TE BAL 4 .SSDR 5 BACKL GHT 6 DNR3 7 DAY/N GHT 8 SPEC AL 9 EX T DC ATW OFF OFF ON AUTO SAVE 2. Select a desired function using the Function Setup switch. - Place the cursor over a desired item. 3. Set up a selected item by using the Function Setup switch. 4. To finish the setting, select 'EXIT' and press the Function Setup switch.
USER’S MANUAL - FOCUS ADJ: To adjust the DC lens focus correctly, you must activate the Focus Settings mode under each lens menu. Activate the Focus Settings mode, adjust the lens focus, and then deactivate the settings mode. ☞NOTE ■ If color rolling occurs when using a DC lens, set Shutter to Fixed (---). ● Exposure Setting MA N SETUP 1 LENS 2 EXPOSURE 3 WH TE BAL DC ATW 1. When the SETUP menu screen is displayed, select 'EXPOSURE' by using the Function Setup Switch. 2.
USER’S MANUAL ◆ AGC (AUTO GAIN CONTROL): The higher the gain level, the brighter the screen but the higher the noise. * OFF: Deactivates the AGC function. * LOW: Allows automatic gain control from 5.3dB to 32dB. * HIGH: Allows automatic gain control from 5.3dB to 37dB. ◆ SENS-UP: When it is night or dark, the camera automatically detects the light level and maintains a clear picture if this mode is activated. * OFF: Deactivates the SENS-UP function. * AUTO: Activates the SENS-UP function.
USER’S MANUAL • Select one of the following 5 modes, as appropriate for your purpose. ATW: Select this when the color temperature is between 1,700˚K and 11,000˚K. OUTDOOR: Select this when the color temperature is between 1,700˚K and 11,000˚K. (sodium light inclusion) INDOOR: Select this when the color temperature is between 4,500˚K and 8,500˚K. MANUAL: Select this to fine-tune White Balance manually. Set White Balance first by using the ATW or AWC mode.
USER’S MANUAL ● Backlight Setting Unlike conventional cameras, W-V chip camera is designed to deliver a distinctive subject and background at the same time, even when the subject is backlight, by using the features of the proprietary W-V DSP chip. 1. When the SETUP menu screen is displayed, select 'BACKLIGHT' by using the Function Setup switch so that the arrow indicates 'BACKLIGHT'. MA N SETUP 1 LENS 2 EXPOSURE 3 WH TE BAL 4 .
USER’S USER’SMANUAL MANUAL HLC SETUP BLC SETUP LEVEL T BOTTOM LEFT R GHT LOW 38 109 54 121 LEVEL L M TS MASK COLOR MASK TONE TOP BOTTOM LEFT R GHT Press Set to Return M DDLE N GHT ONLY BLACK 1 5 120 5 172 Press Set to Return ☞NOTE ■ Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen, optimize the installation angle for the best HLC performance.
USER’S MANUAL 3. Set the DNR3 mode to 'ON' and press the Function Setup switch. Then you can adjust the noise reduction level. ☞NOTE ■ You cannot set the DNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is ‘OFF’. ■ When adjusting the noise reduction level in the DNR3 mode, remember that the higher the level set, the more the noise level will be reduced, as will the brightness of the image. ● Day/Night Setting You can display pictures in color or black and white. 1.
USER’S MANUAL • AUTO: The mode is switched to 'Color' in a normal environment, but switches to 'B/W' mode when ambient illumination is low. To set up the switching time for AUTO mode, press the Function Setup switch. You can turn on or off the burst signal on B/W mode. - BURST MODE: You can turn on or off the burst signal AUTO SETUP on B/W mode. ON 1 BURST MODE - DURATION: You can select brightness of illumination 2 COLOR→B/W DURAT ON FAST about changing the day/night mode.
USER’S MANUAL 2. Select a desired mode using the Function Setup switch. SPEC AL 1 MAGE ADJ 2 .MON TOR 3 .CAM T TLE 4 .SYNC 5 .MOT ON DET 6 .PR VACY 7 .LANGUAGE 9 .RETRUN LCD OFF NT OFF OFF ENGL SH • IMAGE ADJ.: 1) When the SETUP menu screen is displayed, select 'IMAGE ADJ' by using the Function Setup switch so that the arrow indicates 'IMAGE ADJ'. 2) Select a desired mode using the Function Setup switch. MAGE SETUP 1 V-REV 2 H - REV 3 D - ZOOM 4 .D S 5 .FONT COLOR 6 . SHARPNESS 7 .
USER’S MANUAL ☞NOTE ■ When the V-REV or H-REV mode is enabled, the text on the screen does not flip. ■ If you increase the SHARPNESS level too high, the picture may become distorted or noise may appear. • CAM TITLE: If you enter a title, the title will appear on the monitor. 1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates 'CAM TITLE'. CAMERA T TLE SETUP 2) Set it to 'ON' by using the Function Setup switch.
USER’S MANUAL ☞NOTE ■ When using AC power at 60Hz(NTSC), 50Hz(PAL), frequency, you can use the L/L type synchronization. ■ When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode. • MOTION DET :This product has a feature that MOT ON DET allows you to observe movement of objects in AREA1 1 .SENS T V TY 8 different areas on the screen, and the ON 2 . AREA MODE words 'MOTION DETECTED' appear on the 3 .SEL POS L- TOP . 4 XPOS 3 screen when movement is detected. 5 .
USER’S MANUAL 1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that the arrow indicates 'PRIVACY'. 2) Set up the mode using the Function Setup switch. - AREA: You can select up to 12 PRIVACY areas. - MODE: Determines whether to use the area selected in the AREA. - MASK COLOR: Determine area color. You can select Green, Red, Blue, Black, White, Gray. - MASK TONE: Adjust the brightness of MASK COLOR. - TOP/BOTTOM/LEFT/RIGHT: Adjust the size and position of the selected area.
USER’S MANUAL Trouble Shooting ● PROBLEM Northing appears on the screen. POSSIBLE CAUSE ☞ Check the power cable, power supply output and video connection between the camera and monitor. ☞ Are the camera lens or the lens glass dirty? The image on the screen is dim. The image on the screen is dark. ☞ Adjust the contrast control of the monitor. The camera is not working properly and the surface of the camera is hot.
USER’S MANUAL 21