MG2S Spec Sheet

ManualsBrandsRevolv ManualsFurnacesMG2S - 60k BTU - Two-Stage Gas Furnace - Manufactured Home - 96% AFUE - Top Return - Includes Coil Cabinet

• ECM blower: Designed to give a wide range of cooling and

heating airﬂows.

• 2 Stage gas valve: Provides 2-stage thermostat control.

• 2 Stage inducer: Optimizes efﬁciency on ﬁrst stage heat

and reduces sound levels.

• 100% ﬁred and tested: All units and each component (both

mechanical and electrical) are tested on the manufacturing

line.

• Clean and quiet operation: Due to the unique design of

in-shot burners, location of inducer and use of insulation.

• Fixed 30 second blower delay: At burner start-up

assures a warm outlet air temperature at furnace start-up.

Adjustable blower off settings (60, 90, 120 and 180 seconds).

• Fixed 30-second post purge: Increases life of heat

exchanger.

• Dependable, hot surface ignitor: Innovative application

of silicon nitride type igniter. Utilizes proven Smartlite

technology.

• Tubular primary heat exchanger: Heavy gauge aluminized

steel heat exchanger assures a long life.

• Stainless steel secondary heat exchanger: Assures a

long life.

• 60 second ﬁxed cooling cycle blower-off delay (TDR):

Increases cooling performance when matched with an

approved coil.

• Sealed combustion approved for direct vent furnace,

category IV venting system: May be vertically or horizontally

vented using a two-pipe system for maximum ﬂexibility in

installation.

• LP convertible: Simple burner oriﬁces and gas valve

regulator change for ease of convertibility.

• 3 amp fuse protection against low voltage shorts: Protects

transformer and control board.

• Low voltage terminal board: For easy ﬁeld wiring.

• Easy open pawl latch: Secures the door ﬁrmly for transit,

yet allows easy removal for access.

• Appliance quality door: Protects against rust and other

corrosion. Baked enamel ﬁnish allows for easy cleaning.

• Fully insulated cabinet: Insures minimized heat loss and

quiet operation.

• Color coded wire harness: Designed to ﬁt the components,

all with quick-connect ﬁttings for ease of service and

replacement.

• 40VA transformer included.

• Diagnostic lights for easy troubleshooting without

counting ﬂashes: Dedicated light for ﬂame signal strength

and 2 lights in combination to indicate all other fault codes

with easy to recognize states without counting ﬂashes.

Induced Draft - 96% AFUE

Input 45,000 thru 72,000 Btuh

MG2S Series

High Efﬁciency / Direct Vent

Downﬂow 2-Stage Gas Furnace with

Fixed Speed Blower

The high efﬁciency downﬂow gas furnace is especially

designed for manufactured and modular housing. It may

be installed in a utility room, or enclosed in a closet. ITS

design certiﬁed for use in the United States and Canada.

FEATURES and BENEFITS

TECHNICAL

SPECIFICATIONS

Front Return

Models

Top Return

Models

Note: The MG2S will ﬁt in the same footprint, use the same

duct connector, and allow for direct substitution in place of

the M7 furnace.

Summary of content (8 pages)

PAGE 1
TECHNICAL SPECIFICATIONS MG2S Series FEATURES and BENEFITS High Efficiency / Direct Vent Downflow 2-Stage Gas Furnace with Fixed Speed Blower Induced Draft - 96% AFUE Input 45,000 thru 72,000 Btuh The high efficiency downflow gas furnace is especially designed for manufactured and modular housing. It may be installed in a utility room, or enclosed in a closet. ITS design certified for use in the United States and Canada.
PAGE 2
FEATURES High Efficiency Downflow 96% AFUE Gas Furnace Downflow Furnace Blower Assembly STATUS LIGHTS L2-OUT RED RED Y/Y2_OUT L1-IN Y1_OUT L1-OUT FAN SPEED DHUM_IN 1 2 3 4 5 6 78 HEAT Y1_IN COOL SENSOR C CONNECTION TO FURNACE CONTROL BOARD GROUND INPUT TERMINALS OFF ON H_OUT R EXPANSION PORT ON/OFF Switch Motor Control Board GREEN W_OUT OUTPUT TERMINALS Exhaust Vent Pipe L2-IN MOTOR WIRING HARNESS Control Board Inline Drain Assembly SIDE Inducer Assembly Combustion Air Pipe Ga
PAGE 3
DIMENSIONS 17 2 1/2 x 5 (Ventilaire) 3 1/2 (X2) 5 3 2 2 3/4 2 5/8 1 1/2 2 15 1/2 1 1/2 18 1/2 2 Knockouts (x4) Knockouts (x4) 18 1/2 18 1/2 7/8 (Electric) 18 1/2 2 3/4 55 76 1 1/2 X 3 1/2 (Gas) 1 1/2 X 3 1/2 (Gas) 3 1/2 1 7/8 43 1/2 21 1/4 19 7/8 21.250 19 7/8 24 5/8 1 1/2 X 3 1/2 (Gas or Condensate - Typical) 1/2 TYP. 15 21 5/8 TYP.
PAGE 4
DIMENSIONS BW Top 1 1 17 3/4 17 3/4 Knockouts (x4) 15 1/2 Knockouts (x4) 2 1/2 x 5 15 1/2 (Ventilaire) 2 1/2 x5 (Ventilaire) 3 1/2 (X2) 3 1/2 (X2) 5 5 2 2 18 1/2 18 1/2 Knockouts (x4) 18 1/2 Knockouts (x4) 18 1/2 1/2 3 2 2 2 5/8 2 5/8 3 2 3/4 2 3/4 1 1/2 1 1/2 1/2 1 1/2 1 1/2 18 1/2 18 1/2 20 1/4 18 1/2 18 1/2 2 2 Knockouts (x4) Knockouts (x4) 17 1/8 7/8 (Electric) 7/8 (Electric) 55 2 3/4 2 3/4 55 76 76 3 1/2 3 1/2 1 7/8 1 7/8 43 1/2 43 1/2 1 1/2 X 3 1/2 21 1/4 (Gas 1 1/2or X Con
PAGE 5
BLOWER PERFORMANCE - Front Return MOTOR SWITCH SETTINGS (0 =OFF,1 =ON) MODEL NUMBER MG2S-045F* MG2S-060F* MG2S-072F COOLING HEATING EXTERNAL STATIC PRESSURE (IN.W.C.) EXTERNAL STATIC PRESSURE (IN.W.C.) 0.2 0.3 0.4 0.5 0.2 0.3 0.4 0.
PAGE 6
BLOWER PERFORMANCE - Top Return MOTOR SWITCH SETTINGS (0 =OFF,1 =ON) MODEL NUMBER MG2S-045T* MG2S-060T* MG2S-072T COOLING HEATING EXTERNAL STATIC PRESSURE (IN.W.C.) EXTERNAL STATIC PRESSURE (IN.W.C.) 0.2 0.3 0.4 0.5 0.2 0.3 0.
PAGE 7
MODEL IDENTIFICATION CODE M G 2 S - 045 F 2 A B M 1 Manufactured Housing Revision Gas Furnace Cabinet Width M = Manufactured Housing B = 17.5" C = 21.0" Series Efficiency (AFUE) E = 80.0% H = 83.0% J = 84.5% P = 92.1% R = 95.0% S = 96.
PAGE 8
ACCESSORIES Description Duct Connector Kits Part Number Duct Connector Type & Part Number Automatic Cavity Damper 901083 Side Return Air Kit 904003 If Floor Cavity (“X”) is: Neutralizer Kit - All Models 902377 Finger Tab Screw Down 7/8” (22) 901987A 904008 PVC Isolation Kit 904063 2” (51) 901988A 904009 904106 4-1/4” (108) 901989A 904010 Soffit Air Inlet (for VentilAire III only) 917201A 6-1/4” (159) 901990A 904011 VentilAire III - Sloped 3/12 914098B 8-1/4” (210) 901991A