user manual Fridge-Freezer FI250/2TA+
electrolux Electrolux. Thinking of you. Share more of our thinking at www.electrolux.
electrolux 3 • It is dangerous to alter the specifications or modify this product in any way. Any damage to the cord may cause a short-circuit, fire and/or electric shock. Warning! Any electrical component (power cord, plug, compressor) must be replaced by a certified service agent or qualified service personnel. 1. Power cord must not be lengthened. 2. Make sure that the power plug is not squashed or damaged by the back of the appliance. A squashed or damaged power plug may overheat and cause a fire. 3.
electrolux Service • Any electrical work required to do the servicing of the appliance should be carried out by a qualified electrician or competent person. • This product must be serviced by an authorized Service Centre, and only genuine spare parts must be used. Environment Protection This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish.
electrolux 5 partment let the appliance run at least 2 hours on the higher settings. Important! In the event of accidental defrosting, for example due to a power failure, if the power has been off for longer than the value shown in the technical characteristics chart under "rising time", the defrosted food must be consumed quickly or cooked immediately and then re-frozen (after cooling).
electrolux Helpful hints and tips Hints for energy saving • Do not open the door frequently or leave it open longer than absolutely necessary. • If the ambient temperature is high and the Temperature Regulator is set to low temperature and the appliance is fully loaded, the compressor may run continuously, causing frost or ice on the evaporator. If this happens, set the Temperature Regulator toward warmer settings to allow automatic defrosting and so a saving in electricity consumption.
electrolux 7 charging must therefore only be carried out by authorized technicians. Periodic cleaning The equipment has to be cleaned regularly: • clean the inside and accessories with lukewarm water and some neutral soap. • regularly check the door seals and wipe clean to ensure they are clean and free from debris. • rinse and dry thoroughly. Important! Do not pull, move or damage any pipes and/or cables inside the cabinet.
electrolux Periods of non-operation When the appliance is not in use for long periods, take the following precautions: • disconnect the appliance from electricity supply • remove all food • defrost 4)and clean the appliance and all accessories • leave the door/doors ajar to prevent unpleasant smells. If the cabinet will be kept on, ask somebody to check it once in a while to prevent the food inside from spoiling in case of a power failure.
electrolux 9 Problem Possible cause Solution The temperature regulator is not set correctly. Set a lower temperature. The door is not closed correctly. Refer to "Closing the door". The product temperature is too high. Let the product temperature decrease to room temperature before storage. Many products are stored at the same time. Store less products at the same time. The temperature in the refrigerator is too high. There is no cold air circulation in the appliance.
electrolux Technical data Dimension of the recess Height 1446 mm Width 560 mm Depth 550 mm Rising Time 20 h The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label. Installation Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance.
electrolux 11 50-min. cm2200 min. cm2200 Installing the appliance On the opposite side: 1. Tighten the lower pin. 2. Install the lower door. 3. Tighten the middle hinge. 4. Install the spacer. 5. Install the upper door. 6. Tighten the upper pin. Caution! Make sure that the mains cable can move freely. Do these steps. 1. Install the appliance in the niche. Push the appliance in the direction of the arrows (1) until the upper gap cover stops against the kitchen furniture.
electrolux between the appliance and the kitchen furniture is correct. Open the door. Put the lower hinge cover in position. 4mm 5. Remove the correct part from the hinge cover (E). Make sure to remove the part DX, in the case of right hinge, SX in opposite case. 44mm 3. Attach the appliance to the niche with 4 screws. I 6. Attach the covers (C, D) to the lugs and the hinge holes. Install the vent grille (B). Attach the hinge covers (E) to the hinge. 4.
electrolux 13 Put together the appliance door and the furniture door and mark the holes. Ha Hb 8 mm Hc Hd 8. Install the part Ha on the inner side of the kitchen furniture. Ha Hb 11. Remove the brackets and mark a distance of 8 mm from the outer edge of the door where the nail must be fitted (K). ca. 50 mm 90° 8 mm 21 mm 90° ca. 50 mm 21 mm 9. Push the part Hc on the part Ha. Ha Hc 10. Open the appliance door and the kitchen furniture door at an angle of 90°.
electrolux Use the sliding system previously illustrated or open one of the two doors by fitting the small handle supplied as an accessory. Hb 13. Press the part Hd on the part Hb. Do a final check to make sure that: • All screws are tightened. • The magnetic sealing strip is attached tightly to the cabinet. Hb Hd 14. To open the doors do these steps. Important! If the ambient temperature is low (for example, in the Winter), the size of the gasket decreases.
electrolux 15
www.electrolux.
