FAVORIT 40010 VI User manual Dishwasher
Contents Thank you for choosing one of our high-quality products. To ensure optimal and regular performance of your appliance please read this instruction manual carefully. It will enable you to navigate all processes perfectly and most efficiently. To refer to this manual any time you need to, we recommend you to keep it in a safe place. And please pass it to any future owner of the appliance. We wish you much joy with your new appliance.
Safety information 3 Operating instructions Safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features.
Product description Installation • Check your dishwasher for any transport damage. Never connect a damaged machine. If your dishwasher is damaged contact your supplier. • All packaging must be removed before use. • Any electrical and plumbing work required to install this appliance must be carried out by a qualified and competent person. • For safety reasons it is dangerous to alter the specifications or attempt to modify this product in any way.
Control panel 6 7 8 9 5 Rating plate Filters Lower spray arm Upper spray arm Control panel 1 2 3 4 5 Programme selection buttons Delay start button Indicator lights On/off button Function buttons Indicator lights Salt Illuminates when the special salt has run out. 1) Rinse aid Illuminates when the rinse aid has run out. 1) End of programme Illuminates when a washing programme has ended.
First use Setting mode The appliance is in setting mode when all programme lights are illuminated. Always remember that when performing operations such as: • selecting a washing programme • setting the water softener • activating/deactivating the audible signals the appliance MUST be in setting mode. If a programme light is illuminated, the last performed programme is still set. In this case, to return to setting mode, the programme has to be cancelled.
Set the water softener 7 If you want to use combi detergent tablets ("3 in 1", "4 in 1", "5 in 1" etc... ) follow the instructions given in "Use of detergent". Set the water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance. The higher the content of these minerals and salts, the harder your water is.
Use of dishwasher salt Setting electronically The dishwasher is factory set at level 5. 1. Press the On/Off button. The dishwasher must be in setting mode. 2. Press simultaneously and keep pressed buttons B and C, until the lights of buttons A, B and C start flashing. 3. Press button A, the lights of buttons B and C turn off while the light of button A goes on flashing. At the same time the End of programme indicator light starts flashing along with a sequence of intermittent audible signals.
Use of rinse aid 9 3. Using the funnel provided, pour in the salt until the container is full. 4. Replace the cap making sure that there is no trace of salt on the screw thread or on the gasket. 5. Replace the cap tightly turning it clockwise until it stops with a click. Do not worry if water overflows from the unit when filling with salt, this is quite normal.
Daily use 2. Add the rinse aid in the container. The maximum level for filling is indicated by "max". The dispenser holds about 110 ml of rinse aid, which is sufficient for between 16 and 40 dishwashing cycles, depending upon the dosage setting. 3. Ensure that the lid is closed after every refill. Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash.
Load cutlery and dishes 11 Load cutlery and dishes Sponges, household cloths and any object that can absorb water may not be washed in the dishwasher. • Before loading the dishes, you should: – Remove all left over food and debris. – Soften remnants of burnt food in pans • When loading the dishes and cutlery, please note: – Dishes and cutlery must not impede the rotation of the spray arms. – Load hollow items such as cups, glasses, pans, etc.
Load cutlery and dishes The lower basket Load larger and heavily soiled dishes and pans in the lower basket. To make it easier to load larger dishes, the 2 plate racks on the right in the lower basket can be folded down. The cutlery basket WARNING! Long bladed knives stored in an upright position are a potential hazard. Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket. Take care when loading or unloading sharp items such as knives.
Load cutlery and dishes 1. Place the grid insert on the cutlery basket. 2. Place forks and spoon in the cutlery basket with their handles pointing downwards. For larger utensils, such as whisks, leave off one half of the cutlery grid. The upper basket Load smaller, fragile crockery and long, sharp cutlery in the upper basket. • Arrange items of crockery on and under the folding cup racks so that they are offset from each other and water can reach all items.
Use of detergent • The cup racks can be folded up out of the way for tall crockery items. • Lay or hang wine and brandy glasses in the slots in the cup racks. Use of detergent Only use detergents specifically designed for use in dishwashers. Please observe the manufacturer's dosing and storage recommendations as stated on the detergent packaging. Using no more than the correct amount of detergent contributes to reducing pollution. Fill with detergent 1. Open the lid.
Use of detergent 15 2. Fill the detergent dispenser (1) with detergent. The marking indicates the dosing levels: 20 = approximately 20 g of detergent 30 = approximately 30 g of detergent. 3. All programmes with prewash need an additional detergent dose (5/10 g) that must be placed in the prewash detergent chamber (2). This detergent will take effect during the prewash phase. 4. When using detergent tablets, place the tablet in compartment (1) 5. Close the lid and press until it locks in place.
Washing programmes 1. Fill up the dispensers for salt and rinse aid again. 2. Adjust the water hardness setting to the highest setting and perform washing programme without loading any dishes. 3. Adjust the water hardness setting according to the hardness of the water in your area. 4. Adjust the rinse aid dosage.
Select and start a washing programme 17 Select and start a washing programme Select the washing programme and delay start with the door slightly opened. The start of the programme or the countdown of the delay start will occur only after the closure of the door. Until then it is possible to modify the settings. 1. Check that the baskets have been loaded correctly and that the spray arms are free to rotate . 2. Check that the water tap is opened. 3.
Unloading the dishwasher 1. Switch off the dishwasher by pressing the On/Off button. 2. Open the dishwasher door, leave it ajar and wait a few minutes before removing the dishes; in this way they will be cooler and the drying will be improved. Unloading the dishwasher • Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down before removing from the appliance.
Care and cleaning 19 3. Turn the handle about 1/4 a turn anticlockwise and remove the filter system. 4. Take hold of the coarse filter (A) by the handle with the hole and remove from the microfilter (B). 5. Clean all filters thoroughly under running water. 6. Remove the flat filter from the base of the washing compartment and clean both faces thoroughly. 7. Put the flat filter back in the base of the washing compartment and ensure that it fits perfectly. 8.
What to do if… Prolonged periods of non-operation If you are not using the machine for any prolonged period of time you are advised to: 1. Unplug the appliance and then turn off the water. 2. Leave the door ajar to prevent the formation of any unpleasant smells. 3. Leave the inside of the machine clean. Frost precautions Avoid placing the machine in a location where the temperature is below 0°C.
What to do if… Fault code and malfunction 21 Possible cause and solution • continuous flashing of the light of the run- • Close the water tap and contact your local ning programme, Service Force Centre. • 3 intermittent audible signals • 3 flashes of the end of programme indicator light, Anti-flood device is activated. The programme does not start. • The dishwasher’s door has not been properly closed. Close the door. • The main plug is not plugged in. Insert the main plug.
Technical data The wash results are not satisfactory The dishes are wet and dull • Rinse aid was not used. • The rinse aid dispenser is empty. There are streaks, milky spots or a bluish coating • Decrease rinse aid dosing. on glasses and dishes Water drops have dries onto glasses and dishes • Increase rinse aid dosing. • The detergent may be the cause. Contact the detergent manufacturer’s consumer care line. If after all these checks, the problem persists, contact your local Service Force Centre.
Hints for test institutes Lower basket with cutlery basket Cutlery basket 1) If there are cup racks in place on the lefthand side, remove them.
Installation Installation instructions Installation WARNING! Any electrical and/or plumbing work required to install this appliance should be carried out by a qualified electrician and/or plumber or competent person. Remove all packaging before positioning the machine. If possible, position the machine next to a water tap and a drain. This dishwasher is designed to be fitted under a kitchen counter or work surface.
Water connection 25 The locknut must be correctly fitted to avoid water leaks. (Attention! NOT all models of dishwashers have fill and drain hoses provided with locknut. In this case, this kind of facility is not possible). If the machine is connected to new pipes or pipes which have not been used for a long time, you should run the water for a few minutes before connecting the inlet hose. DO NOT use connection hoses which have previously been used for an old appliance.
Electrical connection The waste connection must be at a height of between 30 cm (minimum) and 100 cm (maximum) from the bottom of the dishwasher. The drain hose can face either to the right or left of the dishwasher. Ensure the hose is not bent or squashed as this could prevent or slow down the discharge of water. The sink plug must not be in place when the machine is draining as this could cause the water to syphon back into the machine.
Environment concerns 27 Environment concerns The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
117969580-14032008 www.electrolux.