-1- -1-
1 Overview Thank you for choosing REXING! We hope you love your new products as much as we do. If you need assistance, or have any suggestions to improve it, please contact us. You can reach us via care@rexingusa.com or call us at (203) 800 - 4466. Our support team will respond you as soon as possible. Always a surprise in Rexing. Check us out here. https://www.facebook.com/rexingusa/ https://www.instagram.com/rexingdashcam/ https://www.rexingusa.
1 Contents Camera Overview……………..……...3 Basic Operation……………………….5 Setup Menu…………………..………..6 Take Photos & Record Video……….
1 Introduction Congratulations on the purchase of your new device. You have selected a high-quality product. The operating instruction is one constituent of this product. It contains important information about safety, use and disposal. Before using the product, familiarise yourself with all operating and safety instructions. Use this product only as described and only for the specified areas of application. Copyright This documentation is subject to copyright protection.
2 The manufacturer accepts no responsibility for damage caused by failure to observe these instructions, improper use, incompetent repairs, making unauthorised. modifications or for using unapproved replacement parts. The operator alone bears liability. When the equipment will be placed in the outdoor filming, rapid changes in the weather could lead to error record. Safety Please read below safety precautions carefully before using the camera. · Do not try to disassemble the product case.
3 Camera Overview 1.Display Screen 2.Up/Video Button 3.Shot Button 4.Right Button 5.OK Button 6.Speaker 7.Menu Button 8.Left Button 9.Playback Button 10.Down/Photo Button 11.Micro SD Card Slot 12.AV Jack 13.USB Jack 14.
4 15.Infrared LEDs 16.Day Camera 17.Front Motion Sensor 18.Side Motion Sensor 19.Status Indicator 20.Night Camera Power Supply Please install batteries before using the camera. ♦ Open the camera case and remove the battery cover. Install 8 pieces of 1.5V AA batteries. Please make sure the electrode is correct.
5 Storage Media Please prepare a Micro SD card and insert it into the camera for saving more files. ♦ Support Micro SD card, up to 512GB. ♦ To avoid malfunction, the memory card should be far away water, strong vibration,dust, hot source and direct sunlight. ♦ Do not insert the memory card forcibly. Please refer to the marking on the camera. � For the first time use, please wait a moment.The camera will be short-circuit, caused by the change of environment's temperature and humidity.
6 Switch the Mode Button to “Off” to turn off the camera. System Setup Switch Mode Button to “Test”, then you can set the camera ‘s parameters as your need. 1. Press Video/Photo button to switch the two modes. 2. Press Menu button to open the setup menu. 3. Press Up/Down button to scan all menu. Then press OK button to enter the options interface. 4. Press Up/Down button to scan all options. And press OK button to confirm options. 5. Press Menu button again to turn back to last menu or exit the setup menu.
7 Setup Menu Mode Set the working mode. In capture mode,the camera just take pictures. In Video mode,the camera just record video. In capture&video mode,the camera will take a photo first,then start to record video. Options：【Photo】/【Video】/【Photo&Video】. Day Photo Resolution Set the still image resolution. Options：【20MP(5200x3900P)】/【16MP(4608x3456P)】 /【12MP(4000x3000P)】/【8MP(3264x2448P)】/【 5MP(2592x1944P)】/【3MP(2048x1536P)】/【 1MP(1280x960P)】. Night Photo Resolution Set the still image resolution.
8 Options：【1 photo】/【2 photos in series】/【3 photos in series】/【10 photos in series】. Day Video Resolution Set the video resolution. The bigger the resolution is ,the longer the video time can be stored. Options：【3840x2160P】/【2688x1520P】/【 1920x1080P】/【1280x720P】/【1280x720P 60FPS】/【 848x480P】/【720x480P】/【640x480P】/【320x240P】. Night Video Resolution Set the video resolution. The bigger the resolution is ,the longer the video time can be stored. Options：【1920x1080P】/【1280x720P】/【640x480P】.
9 Night TL Video Resolution Set the resolution of time lapse video . Options:【1920x1080P】/【1280x720P】. Video Length Set the duration of recording a video clip. The shortest time is 3 seconds and the longest time is 10 minutes. Options：3 seconds~10 minutes. Audio Recording Open this function,the camera will record audio when recording video. Options：【On】/【Off】. Shot Lag Set the time of delay shooting when the camera detects the motion.
10 Options:【On】/【Off】. Sensitivity Motion Sensors Set the sensitivity of the sensors. Environmental impact is small indoors, you can choose “Low”. In outdoor, choose “Middle”in normal condition. Choose “High”if the environment impact is huge outdoors. The temperature can also influence the sensor sensitivity. “High Sensitivity” applies to mild environment. ”Low Sensitivity ”applies to cold environment. Options：【Low】/【Middle】/【High】. Target Recording Time Set the target recording time .
11 In Time lapse menu, there are three options as below. [Normal]: The camera will take pictures automatically as per set time interval. For example,set the interval time to 1 hour, the camera will take a photo each hour. If you want to observe that a Settings Set time lapse Hr：Min ：Sec 00 00 30 Notification:Motion sensors deactivated MENU Back OK Select plant blooms, the camera will take 24 photos in 24 hours to record the whole process of blooming. [TL Video]: You can set the interval time.
12 【Nederlands】/【Portuguese】/【Simplified Chinese】/ 【Traditional Chinese】/【Japanese】. Endless Capture Set the camera to record video in loop,it will loop shooting, the earliest document will be deleted when the card is nearly full, infinite loop. Options：【On】/【Off】. Time & Date Set the date and time of camera. The date format: dd/mm/yyyy, yyyy/mm/dd，mm/dd/yyyy. The time format: 24h，12h. Press Left/Right button to choose the item.Press Up/Down button to adjust the value. And press OK button to confirm.
13 Set the power-on password of the camera. The password is four digits, each digit ranges from 0 to 9 or A to Z. If you forget the password, please reset the camera. Then all parameters will reset to the factory settings re-flash. Options：【On】/【Off】. Beep Sound Open/close the button sound. Options：【On】/【Off】. Format Memory Card Formatting the memory card will delete all data permanently.
14 Options：【Yes】/【No】. Version Look up the Firmware information of the camera. Take Photos,Record Video,Playback Switch the Mode Button to “Test”. (if the camera is turned on in a bright environment, the day camera will be turned on; if the camera is turned on in a dark environment, the night camera will be turned on).In this mode,you can take photos, record video and playback files manually. ♦ Take Photos：Press Photo button to switch to photo mode. Press Shot button to take a picture.
15 1）Delete current file：Delete the current photo or video. Options：【Cancel】/【Delete】. 2）Delete all files：Delete all photo and video files in the memory card. Options：【Cancel】/【Delete】. 3）Activate slide show：Playback the photos in slide way. Each photo display 3 seconds. Press OK button to stop playing. 4）Write protect：Lock the file. It can avoid accident deletion. Options：【Write-protect current file】/【Writeprotect all files】/【Unlock current file】/【Unlock all files】.
16 2. If this lights turn green, you are detected by one of the activated side motion sensors . If lights turn red, you are detected by the front motion sensor . By this way, you can align the camera to the best angle and distance. Working Mode Switch the Mode Button to “On”. After turn on the camera,the screen will display 15 seconds countdown. Then the LEDs and screen will go out. The camera begins to operate independently and enter standby mode.
17 resolution color images with normal brightness during the day. Night Mode At night or in a dark environment, the camera will automatically turns on the night camera, and infrared LEDs will turn on automatically to provide necessary light for taking pictures. This makes it is possible to taking picture at a distance about 3m to 20m without overexposing the at night. However, reflective objects such as traffic signs can cause overexposure if they are located within the recording range.
18 bracket you should ensure that all existing screws are tight.The best installation height distance from the ground about 1 meter. Components 1. Tripod screw 2. Lock nut 3. Pivot bolts 4. Drill holes 5. Hexagonal screw 6. Wall plugs 7. Screws Mounting the wall bracket Required tools ■ Drill ■ 6 mm masonry/concrete drill bit ■ Phillips head screwdriver CAUTION ► Ensure that there are no electric lines, water or heating pipes installed at the proposed drilling location.
19 ► The supplied wall plugs are only suitable for mounting on concrete and stone. Before starting the installation, please check your installation location carefully for its suitability for the plugs. The assembly material used must be suitable for the respective location. If in doubt, consult a professional. Install Steps ♦ Mark the drill holes by holding the foot of the wall bracket at the desired mounting location and marking the hole positions.
20 Connecting To TV The camera can transfer the video signal to an external monitor or a television. Please follow below instructions to operate. 1. Connect the camera to the TV via provided AV cable. 2. Turn on the TV and set it to AV mode. 3. Turn on the camera, switch the Mode Button to“Test”. 4. Once connection is successful,the camera will enter playback mode and the screen turn black. The image will show on the TV.
21 click the removable disk icon that represents the memory card. 3. Copy image or video files from the memory card to your computer. Connecting the Camcorder to a PC by the USB Cable 1. Connect the camera to the computer via USB cable.Turn on the camera,the screen will display”MSDC“. 2. Open [My Computer] or [Windows Explorer]. A"Removable Disk" appears in the drive list. Double-click the "Removable Disk" icon to view its contents. All files are stored in the folder named ”DCIM”. 3.
