V1P Quick Start Guide JP V1P クイックスタートガイド FR Guide de démarrage rapide de la V1P IT Guida di avvio rapido V1P SP Guía de inicio rápido V1P DE V1P Schnellstartanleitung
Table of Contents page English Overview What’s in the Box Camera Overview Installation Basic Operation 4 5 6 8 13 日本語 概説 本製品の同梱物 カメラの概説 画面のアイコン 基本操作 20 21 22 24 29 Français Aperçu Que contient la Boîte Aperçu de la Caméra Installation Opération de Base 36 37 38 40 45 Italiano Descrizione Nella Confezione Descrizione Telecamera Installazione Funzionamento Base 2 52 53 54 56 61
page Español Visión General Qué hay en la Caja Resumen de la Cámara Instalación Operación Básica 68 69 70 72 77 Deutsch Übersicht Verpackungsinhalt Kamera übersicht Installation Grundbedienung 84 85 86 88 93 3
1. Overview Thank you for choosing REXING! We hope you love your new product as much as we do. If you need assistance, or have any suggestions to improve it, please contact us. You can reach us via care@rexingusa.com or call us at (203) 800-4466. Our support team will respond you as soon as possible. Always a surprise in Rexing. Check us out here. https://www.facebook.com/rexingusa/ https://www.instagram.com/rexingdashcam/ https://www.rexingusa.
2. What’s in the box 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 5. 6. 7. 8. 9. 8. 9.
3. Camera Overview 1. 2. 3. 4. 5. 6. 10. 11. 12. 13. 8. 9. 7. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Micro SD Card Slot Power Button Reset Button Menu Button Mode Button REC (Record) Button * OK (Con irm) Button ** MIC (Microphone) Button *** Screen Button Mini-USB Port GPS Logger Port Rear Camera Port Lens Angle Adjustment * The Camera is recording when the LED is flashing red. ** The Camera is recording when the LED is flashing red. The device charging or powered on when the LED is solid blue.
Screen Icons WDR Mode (On) GPS Signal (not connected) Recording Time (Current Clip) Recording (On) Recording Standby Status Video Resolution Loop Recording Time Parking Mode (On) Exposure Value G-Sensor Sensitivity Level MIC (Off) Memory Card (Inserted) Current Date (DD/MM/YYY) Time (24H) GPS Signal (locked) MIC (On) Battery Charging Plate Number 7
4. Installation Step 1: Install the Dash Cam Place the 3M tape on the Mount and properly orient the Mount square to the roof and hood line of the vehicle. Important! Ensure the T-interlock on the Mount is oriented in the correct direction. Firmly press the Mount onto the windshield. Wait at least 20 minutes before mounting the camera. Orientation mount as shown Step 2: Insert the Memory Card The Rexing V1P accepts [Class 10/ UHS-1 or higher] Micro SD memory cards up to 256GB.
Press the Power button to turn the power off Step 3: Power the Camera and Format the Memory Card Power the camera by connecting the charger to the car cigarette lighter and camera. To ensure the V1P records to your memory card properly and without error. Before you start using a new memory card, you must format the card within the camera using the format function. Always backup important data stored on the memory card before formatting.
Connect MiniUSB to the camera Blue LED lights indicate the device is charging or powered You may now disconnect from power. The camera will shut down after 3 seconds. The camera should begin recording automatically the next time it is powered on.
Step 4: Mount the Rear Camera Mount the rear camera as shown below. Use the provided rear camera cable to connect the rear camera to the front camera.
Step 5: Installing the Camera onto the Windshield Place the camera on the mount and carefully route the power cable around the windscreen and tuck in under the trim. Plug the Car Charger Cable into a 12V DC power outlet or the car cigarette lighter. Connect car charger to the camera. The camera will auto-start recording once powered on.
5. Basic Operation Device Power The device is automatically powered on when plugged into a 12V accessory socket or cigarette lighter and receives a charge (i.e.: the vehicle is started.) To turn the device on manually,press and hold the POWER button until the welcome screen appears. The camera will automatically start recording when powered on.
Menu Settings Power the camera on. If the camera is recording, press the REC button to stop recording. Press the MODE button and toggle to the desired mode. Press the MENU button once to enter the settings menu for a Mode. Press the MENU button twice to enter the System Settings.
Video Recording The camera will automatically start recording when the device receives a charge. The LED lights and the red dot will blink when the device is recording. Press the REC button to stop recording. The camera automatically start recording when powered on Video Playback Playback mode Playback of videos can be done on the device or a computer. Also, if you have purchased a Rexing GPS Logger you may play back the recordings in a specialized application.
During playback use the OK (pause), MIC (fast forward) and REC (rewind) buttons to control the video playback. To playback a video on the computer either use an SD card adapter or connect the device to the computer directly using the USB to Mini B 5pin male cable. To playback a video using an SD card adapter, remove the memory card and insert it into an SD card adapter. Place the adapter in the computer. To playback a video using USB cable, connect the USB Cable to the device and the computer.
Parking Monitor Connect the dash cam to the smart hardware kit to activate the parking monitor function (Need to purchase the smart hardware kit separately). Please visit support.rexingusa.com to watch a video tutorial. Wi-Fi Connect Download “Rexing Connect” app from the App Store/Google Play Store. 1. 2. 3. 4. To access or exit the Wi-Fi feature, hold down OK. Open Wi-Fi settings on your phone, ffind “SSID:B50 _ XXXX” from the list, tap to connect.
GPS Logger (Need to purchase separately) When connected to the camera, it will record the speed and location of your vehicle as you drive. GPS Signal (not connected) You can then access this information while playing back your recordings using the GPS Video player (For Windows and Mac, available at rexingusa.com). Press the MENU button twice and enter the System Settings. Toggle to the GPS Speed Unit setting and select your preferred speed unit.
Taking Photos To take a photo, stop video recording and toggle to the Photo Mode. Press the OK Button to take a photo. To view a photo, stop video recording and toggle to the Playback Mode. Press the REC and MIC Buttons to toggle through your photos. To delete a photo, stop video recording and toggle to the Playback Mode and toggle through the videos and photos to the one you want to delete. Press the MENU button once and toggle to the Delete option.
1. 概説 REXINGをお選びいただきありがとうございます! 私たちはお客様が 私たちと同じくらいこの新製品を気に入っていただくことを願ってい ます。 サポートが必要な場合、 または製品を改善するための提案がある場 合は、 ご連絡ください。jpcare@rexingusa.comに電子メールでする できます。当社のサポートチームは、 できるだけ早くお客様からのお 問い合わせにお答えいたします。 REXINGでいつも驚きを。 こちらから最新情報をチェックください https://www.facebook.com/rexingusa/ https://www.instagram.com/rexingdashcam/ https://www.rexingusa.
2. 本製品の同梱物 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 5. 6. 7. 8. 9. 8. 9.
3. カメラの概要 1. 2. 3. 4. 5. 10. 11. 12. 13. 6. 8. 9. 7. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
画面アイコン WDR モード(オン) GPS 信号(未接続) 録画時間 (現在のク リップ) 録画中 (オン) 録画スタンバイス テータス ビデオ解像度 パーキングモード (オン) ループ録画時間 露出値 Gセンサー感度 レベル マイク (オフ) メモリーカード (挿入済み) 現在の日付 (日/月/年) 時刻 (24時間表示) GPS シグナル (ロック済み) マイク (オン) 充電中 車両ナンバー 23
4.
電源ボタンを押して電源 をオフにします メモリカードを初期化する Step 3: カメラの電源を入れ、 カメラを充電器で車両のシガーライターに接続して、カメラの電源 を入れます。 RexingドライブレコーダーV1Pがメモリカードを認識しており、エラ ーなしで記録できることを確認します。新しいメモリカードの使用を開 始する前に、 フォーマット機能を使用してカメラ内のカードをフォ ーマットする必要があります。 フォーマットする前に、メモリカード に保存されている重要なデータを必ずバックアップしておいてく ださい。 メモリカードを初期化するには、 メモリカードが挿入されていること を確認してから、電源に接続して機器の電源を入れます。録画を停 止するには、[REC] ボタンを押してください。次に、[MENU] ボタン を 2 回押して、 システムセットアップメニューに入ります。[REC] ボタ ンと [MIC] ボタンを使って、[Format] メニューを選択します。[OK] ボタンを押して初期化を実行してください。 25
ミニUSB端子に 接続します LED が青く点 灯している場合、 機器が充電中か、 または機器 の電源が入っています これで、 カメラの電源を切ることができます。 カメラは3秒後にシャット ダウンします。 カメラは、次回電源がオンになると自動的に録画を開始 します。 [メニュー] ボタンを2回押します [OK] を押してメモリカード の初期化を実行します 26
Step 4: リアカメラの取り付け 図のようにリアカメラを取り付けます。 リアカメラ拡張ケーブルを使用 して、 ウォータープルーフリアカメラをフロントカメラに接続します。 リアカメラをドライ ブレコーダーに接 続する リアカメラの取り付け 27
Step 5: フロントガラスへのカメラの取り付け カメラをマウントにセットし、電源ケーブルをフロントガラスの周囲に 沿って慎重に配線し、トリムの下へとしまい込みます。 車載充電器を車両の12V DC電源コネクターまたはシガーライタ ー に接続します。 車載充電器をカメラに接続します。電源が入ると、カメラは録画を自 動的に開始します。 ミニ5ピンコネクタ をドライブレコー ダーに差し込みま す 電源ケーブルをドラ イブレコーダーに接 続します 車両の電源コネクター またはシガーライ ターに車載充電器を接 続します 28
5.
メニューの設定 カメラの電源を入れます。 カメラが録画中の場合は、[REC] ボタンをタ ップして録画を停止します。 [MODE] ボタンを押して、設定したいモードに切り替えてください。 [MENU] ボタンを1回押すと、モードの設定メニューが表示されま す。[MENU] ボタンを2回押すと、 システムの設定メニューが表示され ます。 システムのアイコン ビデオモードのアイコン メニューボタンを押して、希望 の設定を選択します モードボタンを押して、希望のモード に切り替えます。 30
ビデオ録画 機 器 が 電 源 に接 続されると、 カメラは自動的に録画を開始 します。録 画 時 に は L E Dライ トと赤 いアイコンが 点 滅しま す。[REC] ボタンを押すと録画 を停止します。 電源がオンになるとカメラは自動的 に録画を開始します ビデオの再生 再生モード ビデオの再生は、機器またはコ ンピュータ上で行うことができ ます。Rexing GPSロガーを購入 している場合は、特殊なアプリ ケーションでビデオを再生する ことができます。 機器でビデオを再生する に は、再 生 モードに 切り替え ます。[REC] ボタンと[MIC] ボタ ンを使用して再生したいビデ オに切り替え、[OK] ボタンを押 して再生します。 ボタンを使用してビデオの再生をコントロールしてください 31
再生中は、[OK] (一時停止)、[MIC] (早送り)、[REC] (巻き戻し)ボタンを 使用してビデオの再生をコントロールできます。 コンピュータでビデオを再生するには、SD カード アダプタを使用す るか、機器をコンピュータにUSBケーブルで直接接続してください。 SDカードアダプタを使用してビデオ を再生するには、メモリカードを取 り外し、SDカードアダプタに挿入し てから、SDカードアダプタをコンピ ュータに挿入します。 USBケーブルを使用してビデオ を再生する場合は、USB ケー ブルで機器をコンピュータと 接続します。機器の電源をオ ンにしてから、[OK]ボタンを押 してマスストレージを選択し ます。 コンピューターで機器のドラ イブにアクセスします。ビデオ は次の場所に保存されます。\ CARDV\MOVIE。再生するビ デオを選択して、再生します。 駐車場モニター USB端子でコ ンピュータと接 続しますます マスストレージ PCカメラ マスストレ ージを選択 します ドライブレコーダーをスマート直接配線コードに接続して、駐車モ ニター機能を有効にします。(スマート直接配線コ
ビデオチュートリアルを見るためには support.rexingusa.com にア クセスしてください。 Wi-Fi接続 App Store またはGoogle Playストアから 「Rexing Connect」 アプ リをダウンロードしてください。 1. 2. 3. 4.
GPSロガー (別途購入する必要があります) カメラに接続すると、運転中の車両 の速度と位置が記録されます。 GPS信号(接続 されていない) GPS Video Playerを使用して録画 を再生しながらこれらの情報にア クセスできます。(Windows と Mac の場合は、rexingusa.comで入手で きます)。 [MENU] ボタンを2回押して、 システ ム設定を表示します。 [GPS Speed Unit] の設定に切り替 え、希望の速度単位を選択しま す。 GPS信号を受信すると、画面のア イコンが青から緑に変わります。 ビデオチュートリアルを見るに はgpsa.rexingusa.
写真を撮る 写真を撮るためには、ビデオ 録画を停止し、写真モードに 切り替えます。 [OK] ボタンを押して写真を 撮ります。 再生モード に切り替え て、 プレビュ ーする写真 を選びます 写真を表示するためには、ビ デオ録画を停止し、再生モー ドに切り替えます。 [REC] および [MIC] ボタンを 押して、写真を切り替えます。 写真を削除するには、ビデオ 録画を停止して再生モード に切り替え、削除したい写真 またはビデオに切り替えま す。 [Delete] ボ タンを選択 します MENU を 1 回押し、削除オプ ションを表示します。 [OK]ボタンを押して、[Delete Current (現在表示している 写真/ビデオを削除)] または [Delete All (すべて削除)] を 選択します。 削除オプシ ョンを選択 します 現在選択しているものを削除 全て削除 35
1. Aperçu Nous vous remercions pour votre choix sur REXING ! Nous espérons que vous aimiez votre nouveau produit autant que nous. Si vous avez besoin d’aide ou vous avez des suggestions pour l’améliorer, veuillez nous contacter. Vous pouvez nous joindre via care@rexingusa.com. Notre équipe d’assistance vous répondra le plus vite possible. Toujours une surprise à Rexing. Consultez-nous ici. https://www.facebook.com/rexingusa/ https://www.instagram.com/rexingdashcam/ https://www.rexingusa.
2. Que contient la boîte 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 5. 6. 7. 8. 9. 8. 9.
3. Aperçu de la Caméra 1. 2. 3. 4. 5. 6. 12. 13. 9. 7. 10. 11. 8. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Emplacement pour carte Micro SD Bouton Alimentation Bouton Réinitialisation Bouton Menu Bouton Mode Bouton REC* Bouton OK** Bouton MIC*** Bouton Ecran Port Mini-USB Port pour enregistreur GPS Port pour caméra arrière Réglage de l’angle d’objectif * La caméra enregistre lorsque la LED clignote en rouge. ** La caméra enregistre lorsque la LED clignote en rouge.
Icônes d’écran Mode WDR (activé) Signal GPS (non connecté) Temps d’enregistrement (Clip actuel) Enregistrement (activé) Etat de veille pour enregistrement Durée d’enregistrement en boucle Valeur d’exposition Résolution de vidéo Mode Parking (activé) Niveau de sensitivité de capteur G Carte mémoire (insérée) MIC (désactivé) Date actuelle (JJ/MM/AAAA) Heure (24H) Signal GPS (verrouillé) MIC (activé) Batterie en recharge Numéro de plaque 39
4. Installation Étape 1: Installez la caméra de tableau de bord Placez le ruban 3M sur le support et orientez correctement le support carré par rapport au toit et au capot du véhicule. Important ! Assurez-vous que le T-interlock sur le support soit orienté dans la correcte direction. Appuyez fermement le support sur le pare-brise. Attendez au moins 20 minutes avant de monter la caméra.
Appuyez sur le bouton Alimentation pour éteindre l’appareil 3: Alimentez la caméra et formatez la carte mémoire Alimentez la caméra en connectant le chargeur à l’allume-cigare du véhicule et à la caméra. Pour garantir que la V1P enregistre correctement et sans erreur sur votre carte mémoire, avant de commencer à utiliser une nouvelle carte mémoire, vous devez formater la carte dans la caméra à l’aide de la fonction de formatage.
Connectez le Mini-USB à la caméra Le voyant LED bleu indique que l’appareil est en charge ou sous tension Maintenant vous pouvez vous déconnecter de l’alimentation. La caméra s’éteindra après 3 secondes. La caméra devrait commencer à enregistrer automatiquement la prochaine fois qu’elle sera allumée.
Étape 4 : Installez la caméra arrière Installez la caméra arrière comme indiqué ci-dessous. Utilisez le câble de caméra arrière fourni pour connecter la caméra arrière à la caméra avant.
Étape 5 : Installez la caméra sur le pare-brise Placez la caméra sur le support et passez soigneusement le câble d’alimentation autour du pare-brise et glissez-le sous la garniture. Branchez le câble du chargeur du véhicule sur une prise de courant 12 Vcc ou sur l’allume-cigare du véhicule. Connectez le chargeur du véhicule à la caméra. La caméra démarrera automatiquement l’enregistrement une fois qu’elle est allumée.
5. Opération basique Alimentation pour appareil L’appareil s’allume automatiquement lorsqu’il est branché à une prise accessoire 12V ou à un allume-cigare lorsqu’il est mis sous tension (c’est-à-dire : le véhicule est démarré). Pour allumer l’appareil manuellement, maintenez enfoncé le bouton Alimentation jusqu’à ce que l’écran d’accueil apparaisse. La caméra démarre lorsqu’elle est allumée.
Menu Réglage Allumez la caméra. Si la caméra enregistre, appuyez sur le bouton REC pour arrêter l’enregistrement. Appuyez sur le bouton MENU et passez au mode souhaité. Appuyez une fois sur le bouton MENU pour accéder au menu de réglage pour un mode. Appuyez deux fois sur le bouton MENU pour accéder au Réglage du système.
Enregistrement video La caméra démarre automatiquement l’enregistrement lorsque l’appareil est mis sous tension. Le voyant LED et le point rouge clignotent en rouge lorsque l’appareil enregistre. Appuyez sur le bouton REC pour arrêter l’enregistrement. La caméra démarre automatiquement l’enregistrement lorsque l’appareil s’allume. Lecture des enregistrées vidéos Mode Lecture La lecture des vidéos enregistrées peut être effectuée sur l’appareil ou un ordinateur.
Pendant la lecture, utilisez les boutons OK (pause), MIC (avance rapide) et REC (recul rapide) pour contrôler la lecture vidéo. Pour lire une vidéo sur l’ordinateur, utilisez un adaptateur de carte SD ou connectez l’appareil à l’ordinateur directement à l’aide d’un câble USB. Pour lire une vidéo à l’aide d’un adaptateur de carte mémoire SD, retirez la carte mémoire et insérez-la dans un adaptateur de carte SD. Placez l’adaptateur dans l’ordinateur.
(vous devez acheter le kit de câblage intelligent séparément). Veuillez visiter support.rexingusa.com pour regarder un tutoriel vidéo. Connexion Wi-Fi Téléchargez l’application « Rexing Connect » depuis App Store/Google Play Store. 1. 2. 3. 4. Pour accéder ou quitter la fonction Wi-Fi, maintenez enfoncé le bouton REC. Ouvrez le réglage Wi-Fi sur votre téléphone, recherchez « SSID : B50—XXXX » dans la liste, appuyez sur la touche pour vous connecter.
Enregistreur GPS (Besoin d’acheter séparément) Lorsqu’il est connecté à la caméra, il enregistre la vitesse et l’emplacement de votre véhicule pendant que vous conduisez. Signal GPS (non connecté) Vous pouvez ensuite accéder à ces informations pendant la lecture de vos enregistrements à l’aide du lecteur vidéo GPS (pour Windows et Mac, disponible sur rexingusa.com). Appuyez deux fois sur le bouton MENU pour passer au Réglage du système.
Photographie Pour prendre une photo, arrêtez l’enregistrement vidéo et passez en mode Photo. Appuyez sur le bouton OK pour prendre une photo. Passez au mode Lecture et sélectionnez une photo à voir Pour afficher une photo, arrêtez l’enregistrement vidéo et passez en mode Lecture. Appuyez sur les boutons REC et MIC pour parcourir vos photos. Pour supprimer une photo, arrêtez l’enregistrement vidéo et passez en mode Lecture et parcourez entre les vidéos et les photos pour celle que vous souhaitez supprimer.
1. Descrizione Grazie per aver scelto REXING! Speriamo che ami il tuo nuovo prodotto tanto quanto noi. Se hai bisogno di assistenza o hai suggerimenti per migliorarlo, ti preghiamo di contattarci. Puoi contattarci tramite care@ rexingusa.com. Il nostro team di supporto ti risponderà il prima possibile. Sempre una sorpresa in Rexing. Scoprici qui. https://www.facebook.com/rexingusa/ https://www.instagram.com/rexingdashcam/ https://www.rexingusa.
2. Nella Confezione 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 5. 6. 7. 8. 9. 8. 9.
3. Descrizione Telecamera 1. 2. 3. 4. 5. 10. 11. 12. 13. 6. 8. 9. 7. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Slot per Scheda Micro SD Pulsante di Alimentazione Pulsante RESET Pulsante MENU Pulsante MODALITÀ Pulsante REC * Pulsante OK ** Pulsante MIC *** Pulsante SCHERMO Porta del Mini-USB Porta del Logger CPS Porta della Telecamera Posteriore Regolazione dell’angolo dell’obiettivo *La telecamera sta registrando quando il LED lampeggia in rosso.
Icone dello Schermo Modalità WDR (accesa) Segnale GPS (non connesso) Tempo di registrazione (calo attuale) Registrazione (accesa) Registrazione dello Stato di Attesa Tempo di Registrazione del Ciclo Valore di Esposizione Risoluzione video Modalità di Parcheggio (accesa) Livello di Sensibilità del Sensore G.
4. Installazione Passo 1: Installare la Dash Cam Posiziona il nastro 3M sul Supporto e orienta correttamente il quadrato del Supporto verso il tetto e la linea del cofano del veicolo. Importante! Assicurati che l’interblocco a T sul Supporto sia orientato nella direzione corretta. Premi con forza il Supporto sul parabrezza. Attendi almeno 20 minuti prima di montare la telecamera.
Premere il pulsante di accensione per spegnere Passo 3: Alimentare la Telecamera e Formattare la Scheda di Memoria Alimenta la telecamera connettendo all’accendisigari e alla telecamera dell’auto. il caricabatterie Per garantire che la V1P sulla tua scheda di memoria registri sulla tua scheda di memoria correttamente e senza errori. Prima di iniziare a usare una nuova scheda di memoria, devi formattare la scheda all’interno della telecamera usando la funzione di formattazione.
Connetti Mini-USB alla telecamera Le luci LED blu indicano che il dispositivo è in ricarica o acceso Ora puoi disconnetterti dall’alimentazione. La telecamera si spegnerà dopo 3 secondi. La telecamera dovrebbe iniziare a registrare automaticamente la prossima volta che viene accesa.
Passo 4: Montare La Telecamera Posteriore Monta la telecamera posteriore come mostrato di seguito. Usa il cavo della telecamera posteriore in dotazione per connettere la telecamera posteriore alla telecamera anteriore.
Passo 5: Installare la Telecamera sul Parabrezza Posiziona la telecamera sul supporto e instrada attentamente il cavo di alimentazione attorno al parabrezza e infilalo sotto il rivestimento. Collega il Cavo del Caricabatterie per Auto a una presa di corrente da 12 V CC o all’accendisigari dell’auto. Connetti il caricabatterie per auto alla telecamera. La telecamera avvierà automaticamente la registrazione una volta accesa.
5. Funzionamento Base Accensione del Dispositivo Il dispositivo si accenderà automaticamente quando collegato a una presa per accessori da 12 V o all’accendisigari e riceve una ricarica (ovvero: il veicolo viene avviato). Per accendere manualmente il dispositivo, premi e tieni premuto il pulsante di ACCENSIONE fino a quando appare la schermata di benvenuto. La telecamera inizierà automaticamente a registrare quando è accesa.
Impostazioni Menu Accendi la telecamera. Se la telecamera sta registrando, premi il pulsante OK per interrompere la registrazione. Premi il pulsante MODALITÀ e passa alla modalità desiderata. Premi una volta il pulsante MENU per accedere al menu delle impostazioni per una Modalità. Premi due volte il pulsante MENU per accedere alle Impostazioni di Sistema.
Registrazione Video La telecamera avvierà automaticamente la registrazione quando il dispositivo riceve una ricarica. Le luci LED e il punto rosso lampeggeranno durante la registrazione. Premi il pulsante REC per interrompere la registrazione. La telecamera avvia automaticamente la registrazione all’accensione Riproduzione Video Modalità di riproduzione La riproduzione di video può essere eseguita sul dispositivo o su un computer.
Durante la riproduzione, usa i pulsanti OK (pausa), MIC (avanzamento rapido) e REC (riavvolgimento) per controllare la riproduzione del video. Per riprodurre un video sul computer, usa un adattatore per scheda SD o connetti il dispositivo al computer direttamente usando il cavo USB. Per riprodurre un video usando un adattatore per scheda SD, rimuovi la scheda di memoria e inseriscila in un adattatore per scheda SD. Posiziona l’adattatore nel computer.
Monitor di Parcheggio Connetti la dash cam al kit hardwire intelligente per attivare la funzione di monitore di parcheggio (È necessario acquistare il kit hardwire intelligente separatamente). Si prega di visitare support.rexingusa.com per guardare un video tutorial. Connessione Wi-Fi Scarica l’app “Rexing Connect” dall’App Store / Google Play Store. 1. Per accedere o uscire dalla funzione Wi-Fi, tieni premuto REC. 2.
GPS Logger (È necessario acquistare separatamente) Quando è connesso alla telecamera, registrerà la velocità e la posizione del tuo veicolo mentre guidi. Segnale GPS (non connesso) Puoi quindi accedere a queste informazioni durante la riproduzione delle tue registrazioni usando il lettore Video GPS (Per Windows e Mac, disponibile su rexingusa.com). Premi due volte il pulsante MENU e accedere alle Impostazioni di Sistema.
Scattare Foto Per scattare una foto, interrompi la registrazione video e passa alla Modalità di Foto. Premi il Pulsante OK per scattare una foto. Passa alla modalità di Riproduzione e seleziona una foto da visualizzare Per visualizzare una foto, interrompi la registrazione video e passa alla Modalità di Riproduzione. Premi i pulsanti di navigazione SU e GIÙ per passare da una foto all’altra.
1. Visión General ¡Gracias por elegir REXING! Esperamos que usted ame su nuevo producto tanto como nosotros la amamos. Si usted necesita ayuda o tiene alguna sugerencia para mejorarla, contáctenos. Puede comunicarse con nosotros a través de care@rexingusa.com. Nuestro equipo de soporte le responderá lo antes posible. Siempre es una sorpresa en Rexing. Visítenos aquí. https://www.facebook.com/rexingusa/ https://www.instagram.com/rexingdashcam/ https://www.rexingusa.
2. Qué hay en la caja 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 5. 6. 7. 8. 9. 8. 9.
3. Resumen de la Cámara 1. 2. 3. 4. 5. 10. 11. 12. 13. 6. 8. 9. 7. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Ranura para tarjeta micro SD Botón de encendido Botón de reinicio Botón de menú Botón de modo Botón REC * Botón OK ** Botón MIC *** Botón PANTALLA Puerto mini-USB Puerto de registrador de GPS Puerto de cámara trasera (no compatible) Ajuste de ángulo del lente *La cámara está grabando cuando el LED parpadea en rojo. **La cámara está grabando cuando el LED parpadea en rojo.
Iconos de pantalla Modo AMPLIO RANGO DINÁMICO (activado) Señal de GPS (no conectada) Tiempo de grabación (clip actual) Grabación (activado) Resolución de video Grabación del estado de espera Tiempo de grabación en bucle Valor de exposición Modo de estacionamiento (activado) Sensor G Nivel de sensibilidad Tarjeta de memoria (insertada) Micrófono (apagado) Fecha actual Hora (DD / MM / AAAA) (24h) Señal GPS (bloqueada) Micrófono (activado) Cargar batería Número de placa 71
4. Instalación Paso 1: Instalar la Grabadora de Conducción Coloque la cinta de 3M en el soporte y oriente adecuadamente el cuadrado del soporte al techo y la línea del capó del vehículo. ¡Importante! Asegúrese de que el enclavamiento en T del soporte esté orientado en la dirección correcta. Presione firmemente el soporte sobre el parabrisas. Espere al menos 20 minutos antes de montar la cámara.
Presionar el botón de encendido para apagar Paso 3: Encienda la Cámara y Formatee la Tarjeta de Memoria Encender la cámara a través de conectar el cargador al encendedor de cigarrillo del automóvil y la cámara. Para garantizar que el V1P registre en su tarjeta de memoria correctamente y sin error. Antes de comenzar a usar una nueva tarjeta de memoria, debe formatear la tarjeta dentro de la cámara utilizando la función de formateo.
Conectar el mini usb a la cámara Las luces LED azules indican que el dispositivo está cargando o está encendido Ahora puede desconectarse de fuente de alimentación. La cámara se apagará después de 3 segundos. La cámara debería comenzar a grabar automáticamente la próxima vez que se encienda.
Paso 4: Montar la cámara trasera Montar la cámara trasera como se muestra a continuación. Usar el cable de la cámara trasera provisto para conectar la cámara trasera a la cámara frontal.
Paso 5: Instalación de la Cámara en el Parabrisas Colocar la cámara en el soporte y pasar con cuidado el cable de alimentación alrededor del parabrisas y colocarlo debajo de la moldura. Conectar el cable del cargador de automóvil a una toma de corriente de 12V DC o al encendedor de cigarrillo del automóvil. Conectar el cargador del automóvil a la cámara. La cámara iniciará automáticamente la grabación una vez que esté encendida.
5. Operación Básica Fuente de alimentación del dispositivo El dispositivo se enciende automáticamente cuando se enchufa a una toma de accesorios de 12V o encendedor de cigarrillos y recibe una carga (es decir: el vehículo se enciende). Para encender el dispositivo manualmente, mantenga presionado el botón de ENCENDIDO hasta que aparezca la pantalla de bienvenida. La cámara comenzará a grabar automáticamente cuando se encienda.
Configuraciones de menú Encienda la cámara. Si la cámara está grabando, presione el botón REC para detener la grabación. Presione el botón MODO y cambie al modo deseado Presione el botón MENÚ una vez para ingresar al menú de configuración de un Modo. Presione el botón MENÚ dos veces para ingresar a la Configuración del sistema.
Grabación de vídeo La cámara comenzará a grabar automáticamente cuando el dispositivo recibe una carga. El LED se ilumina y el punto rojo parpadeará cuando el dispositivo esté grabando. Presione el botón REC para detener la grabación.Presione el botón REC para detener la grabación. La cámara comienza a grabar automáticamente cuando se enciende Reproducción de vídeo Modo de reproducción La reproducción de videos se puede hacer en el dispositivo o una computadora.
Durante la reproducción, use OK (pausa), MIC (avance rápido) y Botones REC (rebobinar) para controlar la reproducción de video. Para reproducir un video en la computadora, use un adaptador de tarjeta SD o conecte el dispositivo a la computadora directamente con el cable USB. Para reproducir un video usando un adaptador de tarjeta SD, retire la tarjeta de memoria e insértela en un adaptador de tarjeta SD. Coloque el adaptador en la computadora.
Monitor de estacionamiento Conecte la grabadora cableado inteligente para estacionamiento (necesita inteligente por separado). ver un video tutorial. de conducción al equipo de activar la función de monitor de comprar el equipo de cableado Visite support.rexingusa.com para Conexión de wifi Descargue la aplicación “Rexing Connect” de App Store / Google Play Store. 1. 2. 3. 4. Para acceder o salir de la función Wi-Fi, mantenga presionado REC.
Registrador GPS (Se necesita comprar por separado) Cuando se conecta a la cámara, se registrará la velocidad y la ubicación de su vehículo mientras conduce. Señal de GPS (no conectada) Luego puede acceder a esta información mientras reproduce sus grabaciones utilizando el reproductor de video GPS (para Windows y Mac, disponible en rexingusa.com). Presione el botón MENÚ dos veces y ingrese a la Configuración del sistema.
Tomando fotos Para tomar una foto, detenga la grabación de video y cambie al Modo foto. Presione el botón OK para tomar una foto. Cambie al modo Reproducción y seleccione una foto para ver Para ver una foto, detenga la grabación de video y cambie al Modo de reproducción. Presione los botones REC y MIC para alternar entre sus fotos. Para eliminar una foto, detenga la grabación de video y cambie al Modo de reproducción y cambie entre los videos y las fotos a la que quiere borrar.
1. Übersicht Danke, dass Sie sich für REXING entschieden haben! Wir hoffen, dass Sie Ihr neues Produkt so sehr lieben wie wir. Wenn Sie Hilfe benötigen oder Vorschläge zur Verbesserung haben, kontaktieren Sie uns bitte. Sie können uns erreichen über care@rexingusa.com. Unser Support-Team wird Ihnen so schnell wie möglich antworten. Immer wieder eine Überraschung in Rexing. Schauen Sie hier nach. https://www.facebook.com/rexingusa/ https://www.instagram.com/rexingdashcam/ https://www.rexingusa.
2. Verpackungsinhalt 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 5. 6. 7. 8. 9. 8. 9.
3. Kamera übersicht 1. 2. 3. 4. 5. 10. 11. 12. 13. 6. 8. 9. 7. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Micro-SD-Kartensteckplatz EIN- / AUS-Taste RÜCKSETZUNGS-Taste MENÜ-Taste MODUS-Taste AUFNAHME-Taste * OK-Taste ** MIC-Taste*** BILDSCHIRM-Taste Mini-USB-Anschluss CPS-Logger-Anschluss Rückfahrkamera-Anschluss Objektiv-Winkelverstellung *Die Kamera nimmt auf, wenn die LED rot blinkt. **Die Kamera nimmt auf wenn die LED rot aufblinkt.
Bildschirmsymb WDR-Modus (ein) GPS Signal (nicht verbunden) Schleifenaufnahme Zeit (current clip) Aufnahme (ein) Aufnahme Standby- Status Video Auflösung Schleifenaufnahme Zeit Park-Modus (ein) Belichtungswert G-Sensor Sensibilitätsstufe MIC (Aus) Speicherkarte (eingesteckt) Aktuelles Datum Zeit (TT/MM/JJJJ) (24 Std) GPS Signal (gesperrt) MIC (Aus) Batterie Laden Plattennummer 87
4. Installation Schritt 1: Installation der Dash-Cam Legen Sie das 3M-Band auf die Halterung und richten Sie die Halterung rechtwinklig zur Dach- und Motorhaubenlinie des Fahrzeugs aus. Wichtig! Stellen Sie sicher, dass die T-Verriegelung auf der Halterung in die richtige Richtung ausgerichtet ist. Drücken Sie die Halterung fest auf die Windschutzscheibe. Warten Sie mindestens 20 Minuten, bevor Sie die Kamera montieren.
Drücken Sie die Ein/ Aus-Taste, um das Gerät auszuschalten Schritt 3: Kamera einschalten und Speicherkarte formatieren Schließen Sie das Ladegerät an den Zigarettenanzünder des Autos und die Kamera an, um die Kamera mit Strom zu versorgen. Um sicherzustellen, dass die VIP-Aufzeichnungen korrekt und fehlerfrei auf Ihre Speicherkarte aufzeichnet. Bevor Sie eine neue Speicherkarte verwenden können, müssen Sie die Karte in der Kamera mit der Formatierungsfunktion formatieren.
Mini-USB an die Kamera anschließen Blaue LEDLeuchten zeigen an, dass das Gerät geladen oder eingeschaltet ist Sie können nun die Verbindung zur Stromversorgung trennen. Die Kamera schaltet sich nach 3 Sekunden aus. Die Kamera sollte beim nächsten Einschalten automatisch mit der Aufnahme beginnen. Drücken Sie die MenüTaste zweimal Drücken Sie die OK-Taste, um das Formatieren der Karte zu bestätigen.
Schritt 4: Rückfahrkamera befestigen Montieren Sie die Rückfahrkamera wie unten abgebildet. Verwenden Sie das mitgelieferte Rückfahrkamerakabel, um die Rückfahrkamera mit der Frontkamera zu verbinden.
Schritt 5: Installation der Kamera auf der Windschutzscheibe Legen Sie die Kamera auf die Halterung und führen Sie das Stromkabel vorsichtig um die Windschutzscheibe herum und stecken Sie es unter die Verkleidung. Stecken Sie das Autoladekabel in eine 12 V DC-Steckdose oder in den Zigarettenanzünder des Autos. Schließen Sie das Autoladegerät an die Kamera an. Die Kamera startet die Aufnahme automatisch, sobald sie eingeschaltet wird.
5. Grundbedienung Gerät-Stromversorgung Das Gerät wird automatisch eingeschaltet, wenn es an eine 12 V DC-Steckdose oder einen Zigarettenanzünder angeschlossen und geladen wird (d.h.: das Fahrzeug wird gestartet). Um das Gerät manuell einzuschalten, halten Sie die Ein/AusTaste gedrückt, bis der Begrüßungsbildschirm erscheint. Die Kamera beginnt automatisch mit der Aufnahme, wenn sie eingeschaltet wird. Halten Sie die Ein/Aus-Taste gedrückt, um das Gerät manuell einzuschalten.
Menüeinstellungen Schalten Sie die Kamera ein. Wenn die Kamera gerade aufnimmt, drücken Sie die REC-Taste, um die Aufnahme zu beenden. Halten Sie die MODE-Taste gedrückt und wechseln Sie in den gewünschten Modus. Drücken Sie die MENÜ-Taste einmal, um das Einstellungsmenü für einen Modus aufzurufen. Drücken Sie die Menü-Taste zweimal, um die Systemeinstellungen zu öffnen.
Videoaufnahme Die Kamera beginnt automatisch mit der Aufnahme, wenn das Gerät aufgeladen wird. Die LED leuchtet und der rote Punkt blinkt, wenn das Gerät aufnimmt. Drücken Sie auf die REC-Taste, um die Aufnahme zu beenden. Die Kamera startet die Aufnahme automatisch beim Einschalten Videowiedergabe Wiedergabemodus Die Wiedergabe von Videos kann auf dem Gerät oder einem Computer erfolgen.
Verwenden Sie während der Wiedergabe die Tasten OK (Anhalten), MIC (Vorspulen) und REC (Zurückspulen), um die Videowiedergabe zu steuern. Um ein Video auf dem Computer abzuspielen, verwenden Sie entweder einen SD-Kartenadapter oder schließen Sie das Gerät mit dem USB-Kabel direkt an den Computer an. Um ein Video mit einem SD-Kartenadapter wiederzugeben, entfernen Sie die Speicherkarte und stecken Sie sie in einen SD-Kartenadapter ein. Stecken Sie den Adapter in den Computer ein.
Park-monitor Schließen Sie die Dash-Cam an das Smart Hardwire-Kit an, um die Parkmonitor-Funktion zu aktivieren (das Smart Hardwire-Kit muss separat erworben werden). Bitte besuchen Sie support. rexingusa.com, um ein Video-Tutorial anzusehen. Wi-Fi Verbindung Laden Sie die „Rexing Connect“ –App aus dem App Store/ Google Play Store herunter. 1. 2. 3. 4. Um auf die Wi-Fi-Funktion zuzugreifen oder sie zu beenden, halten Sie REC gedrückt.
GPS-Logger (Muss separat gekauft werden) Wenn die Kamera angeschlossen ist, zeichnet sie während der Fahrt die Geschwindigkeit und den Standort Ihres Fahrzeugs auf. GPS Signal (nicht verbunden) Sie können dann auf diese Informationen zugreifen, während Sie Ihre Aufzeichnungen mit dem GPS-Video-Player wiedergeben (für Windows und Mac, verfügbar unter rexingusa.com). Drücken Sie zweimal die MENÜ-Taste und rufen Sie die Systemeinstellungen auf.
Fotos aufnehmen Um ein Foto aufzunehmen, stoppen Sie die Videoaufnahme und wechseln Sie in den Fotomodus. Drücken Sie die OK-Taste, um ein Foto zu machen. Wechseln Sie in den Wiedergabe modus und wählen Sie ein Foto zur Ansicht Um ein Foto anzusehen, stoppen Sie die Videoaufnahme und wechseln Sie in den Wiedergabemodus. Drücken Sie die Tasten REC und MIC, um durch Ihre Fotos zu blättern.