Replacement Parts Guide

ManualsBrandsReznor ManualsHeatingReplacement Pilot Assembly, NG/LP, up to 6,000 ft

Form P-PILOTS, Page 4

FIGURE 10 - Vertical Spark Pilot for

Models RCG 2 - 5 ton with Vertical Pilot

Protective Boot,

P/N 112648

Effective with replacement pilots

purchased 9/91, these parts are re-

quired (in the kit or separately) when

the replacement pilot is for heater

Models listed in FIGURES 6, 9 and

10 equipped with a Model G60 or

G67BG-NG-2 ignition controller.

(Note: These parts are not required

when the ignition controller is a

Model G67BG-5 or G770NGC-4.)

Crimp-on, 90° Rajah

Terminal Connector,

P/N 112647

1. Identify the ignitor wire attached to the

pilot electrode. Slip the 90° protective

boot on to the wire, as illustrated è.

2. On the "open" leg of the 90° crimp-on

terminal (P/N 112647), locate a flat,

triangular spike tab punched in the

metal. With the tip of a small, straight

screwdriver, force the spike tab toward

the inside of the connector. Straighten

the tab to a vertical position.

3. Insert the ignitor wire into that same

connector leg (just to the 90° bend) and

push the wire onto the protruding spike

tab, making sure that the tab penetrates

the insulation. (Do not strip the ignitor

wire.) Using a crimping tool or pliers,

squeeze the sides of the terminal to

form a "C" shape. The ignitor wire

should now be firmly held by the

terminal.

FIGURE 11 - Pilot Systems used

on Direct-Fired Models RDF/

ADF/ADFH/DFA/DV

Instructions for connecting ignitor lead on replacement spark pilots to Model G60 and G67 ignition

controllers (applies to Pilot Kits in FIGURES 6, 9, and 10):

www.RezSpec.com; 800-695-1901

Trademark Note: Reznor

is registered in at least the United States.

11/10 P-PILOTS (Version .2)

4. Slide the protective boot over the

terminal. Holding the boot, attach the 90

Rajah terminal to the ignitor lead Rajah

connector on the Model G60 or G67BG/

NG-2 ignition controller.

*P/N 135435 is a replace-

ment flame sensor only kit

for ADF/ADFH units manu-

factured prior to 11/94.

Hot Surface Ignition Kits below include all components needed to change RDF units from a

spark pilot system with either a flame probe or ultraviolet sensor to hot surface ignition

- for an RDF unit with a 200VA Transformer - P/N 146268

- for a 115V RDF unit with an 80VA transformer - P/N 146318

- for a 208V RDF unit with an 80VA transformer - P/N 146319

- for a 240V, 480V, or 575V RDF unit with an 80VA transformer - P/N 146320

NOTE: Model, Serial No., and

Wiring Diagram No. MUST be

provided when ordering

these kits.

*See instructions below.

Step 1 - Slip

Boot over

Install boot

and terminal

on ignitor wire

Step 2 & 3 - Attach

90°, Crimp-on

Step 4 - Attach to

Ignition Controller

Replacement Natural Gas - P/N 110867

Pilot Kits Propane Gas - P/N 110868

Code

P/N

Component Description

47484

Natural Gas Pilot with orifice, high tension lead and built-in flame probe; less

pilot tubing, less sensor lead (Baso #J993HHW6221)

47485

Propane Gas Pilot with orifice, high tension lead and built-in flame probe; less

pilot tubing, less sensor lead (Baso #J993HHW4211)

44048

Natural Gas Orifice only, #6221

42089

Propane Gas Orifice only, #4211

44183

Sensor lead, 38" lg

7671

Pilot tubing 26" lg

9664

Nut with breakaway ferrule (2 required when replacing pilot tubing)

112647

Crimp-on, 90

Rajah terminal connector

112648

Boot Terminal Protector

Replacement w/Flame Probe - P/N 110869

(Includes Codes 1, 2, 3)

RDF with spark pilot

Pilot Kits w/Ultraviolet Sensor - P/N 110918

(Includes Codes

1, 2, 4)

RDF with spark pilot

w/Hot Surface Ignition - P/N 120048

(Includes

Codes 5, 6, 7, and 8)

ADF/DFA/RDF/DV wit

hot surface ignition

Code

P/N

Component Description

Applies to

Pilot Supply Connection including: (1) brass elbow,

P/N 93388

; (3) connectors,

P/N 95188

; (1) long nut,

P/N 95189

RDF Models

87936

Spark Plug, 27750-1-31, Maxon #18075

with a spark pilot

87937

Flame Probe, Auburn AA67-7892-1 - Standard on

units with date code prior to ANI (9/88)

and either a probe or

ultraviolet

89411

Ultraviolet Minipeeper, #C7027A - Standard on units

with date code from ANI (9/88) through AVB (2/96) -

optional on prior units

flame sensor

122840

Pilot Plate and Tubing Assembly ADF/ADFH*; DFA;

134706*

Flame Sensor, J/C #Y75MK-1D DV; and RDF with

121865

Ignitor, Norton #401E

hot surface

121730

Pilot Bushing

ignition