Installation - Blower Guard (Options CD10 and CD12) User guide

ManualsBrandsReznor ManualsRadiatorsBE Option

Form RZ-NA I-OPT-G, P/N 101542 (Rev 5), page 1

APPLIES TO: Models UDBP, UDBS,

B, and BE

Guards, Options CD10

and CD12

Installation Form RZ-NA I-OPT-G

Obsoletes Form 434/436-BG (Version A)

C E R T I F I E D

These guard options provide protection from the rotating belt drive and/or blower

components.

Blower Guard Option CD12 is designed for use with Models UDBP and UDBS

30-125 and Models B and BE 25-100 with a standard direct drive motor. Option

CD12 includes only the blower inlet guard.

Option CD10 is designed for use on Models UDBP and UDBS 150-400 and Mod-

els B and BE 50-400 with a belt driven motor. Option CD10 includes both the belt

guard and the blower inlet guard.

Description and

Application

Kit Components

FIGURE 1 -

Guard

Options

Blower Inlet

Guard in

Options CD10

and CD12

Belt Guard in Option CD10

Option CD10 includes:

Option CD12 includes:

tion CD12 for B and BE 25-100 and UDBP and UDBS 30-125

Qty P/N

Option Pkg P/N 114548

Blower Inlet Guard 1 102474

Screws, #10-16 x 1/2" lg 4 37661

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause

property damage, injury or death. Read the installation, operation, and maintenance instructions

thoroughly before installing or servicing this equipment.

50-125 130-165 200-400

Qty P/N Qty P/N Qty P/N

Option Pkg P/N 101539 101540 101541

Blower Inlet Guard 1 102474 1 102475 1 102475

Screws, #10-16 x 1/2" lg for blower inlet guard 4 37661 3 37661 3 37661

Belt Guard 1 193796 1 193797 1 193795

Screws, #10 x 1/2" long for belt guard 5 11813 3 11813 3 11813

Contactor Mounting Bracket * 1 101405 N/A N/A

150-200 225-400

Qty P/N Qty P/N

Option Pkg P/N 202316 202317

Blower Inlet Guard 1 203079 1 102475

Belt Guard 1 193797 1 193795

Green Wire Assembly 1 202939 1 202939

8 37661 8 37661

Screws, #10-16 x 1/2" lg (4 for attaching blower inlet guard; 3 for

attaching belt guard; and 1 for attaching ground wire to blower)

Option CD10 for Models B and BE

*The contactor mounting bracket (the flat sheet metal part with four holes) and the two

additional sheetmetal screws are used only when the belt guard is being installed on a Model

75, 100, or 125 equipped with a motor contactor. Otherwise, these parts are not required and

may be discarded.

Option CD10 for Models UDBP and UDBS

Summary of content (2 pages)

PAGE 1
Guards, Options CD10 and CD12 Installation Form RZ-NA I-OPT-G Obsoletes Form 434/436-BG (Version A) CERTIFIED APPLIES TO: ® Description and Application FIGURE 1 Guard Options Models UDBP, UDBS, B, and BE These guard options provide protection from the rotating belt drive and/or blower components. Blower Guard Option CD12 is designed for use with Models UDBP and UDBS 30-125 and Models B and BE 25-100 with a standard direct drive motor. Option CD12 includes only the blower inlet guard.
PAGE 2
Installation Instructions FIGURE 2 - Blower Inlet Guard Installed Installation should be done by a qualified agency in accordance with these instructions and in compliance with all codes and requirements of authorities having jurisdiction. 1. If the heater is installed, turn off the gas and the electric power. 2. Install Blower Inlet Guard - Options CD10 and CD12 a) Position the guard. See FIGURE 2. b) Mark the mounting holes (3 or 4 depending on guard). c) Drill 1/8" diameter holes.