User's Manual
C
ommand
Data Type
R,
W,
R/W
Definition
r
fid:chr
.
c
ount.
tr
ail
INT
R/W
Verify or
Set
the
trailing character
count
(0 to 3)
u
r
fid:chr
.
eol
CHAR
R/W
Verify or
set end
of
line termination
character
( A -
Z,
0 -
9, a
- z or
ASCII
\0x00
….\0x0D)
r
fid:chr
.
f
ac
CHAR
R/W
Verify or set
separating character between
the facil-
ity
code and
ID data( A -
Z,
0 -
9, a
- z or
ASCII
\0x00
….\0x0D)
Ex: 123 ;
456
7
89
r
fid:chr
.g
one.
1
CHAR
R/W
1st character sent when card
is removed
( A -
Z,
0 -
9, a
- z or
ASCII
\0x00
….\0x0D)
rfid:chr.gone.2 CHAR
R/W
2nd character sent when card
is removed
( A -
Z,
0 -
9, a
- z or
ASCII
\0x00
….\0x0D)
rfid:cmd.echo BOOL
R/W
IF True, enable echo
of
user
input
and use
of
backspac
e
key
r
fid:cmd.prompt BOOL
R/W
IF True, enable RF
IDeas command
prompt
r
fid:dev.luid
INT
(hex)
R/W
Verify or
set
the
logical unique identifier
as 16
bit INT
(0x0000
..
0xFFFF)
r
fid:dev
.par
t
F
unction
Read
the
device
part number
r
fid:dev
.
v
er
F
unction
Read
firmware version
(major
. minor .
variant)
r
fid:disp
.
6
4bit
BOOL
R/W
IF True, use
64 bit
math on
ID data
r
fid:disp
.
f
ac.
6
4bit
BOOL
R/W
IF True, use
64 bit
math on
facility
code
data
rfid:disp.fac.digits INT
R/W
Verify or
set Length
of facility
code
output
(up to 25 digits)
rfid:disp.fac.hex BOOL
R/W
IF True, enable
facility
code
output
as
hex
rfid:disp.fac.send BOOL
R/W
Enable
output of facility code
r
fid:disp
.
f
ac.s
trip
BOOL
R/W
Set
to
True
to
separate
ID
and FAC. False processes
ID
and FAC
t
og
ether
.
rfid:disp.hex.lower
BOOL
R/W
IF True, hex
ID
data
is output in lowercase
r
fid:disp.id.digits BOOL
R/W
Verify or
Set
ID
data length
(0 to 25 digits)
Note:
If
value
is
shorter than actual
Id
length
the left most
significant digits
will
be
truncated
rfid:disp.id.hex BOOL
R/W
IF True, enable
ID
data
output
as
hex
r
fid:help
F
unction
View
menu
of
commands, summary
of output types
and variable
options
rfid:op.beep BOOL
R/W
Beeper
output
control True=beep,
F
alse=silent
r
fid:op
.
c
ont BOOL
R/W
Continuous read mode
True=continuous
output, False=single
output of
credential
data
rfid:op.sdk BOOL
R/W
IF True, enable Quiet mode. (IE: Credential data
is not
displayed) Note:
data can
still
be retrieved
using
function
rfid:qid.
r
fid:out.led INT
R/W
LED
output control
0=off
,
1=red,
2=
gr
een
,
3=Amber
(Immediate
out w\o
writ
e)
255=Automatic control
by
reader (requires
write
t
o
flash) red on standby, green when credential
is read