User manual

Common Questions and Solutions
How to Realize DSK Setting
Before DSK setting, please check the DSK input,
currently, DSK input only support DVI3 input, settings
are as follows:
1. Push [DVI3] button, and make sure there is input
signal, and OLED shows DVI3 signal.
2. Set the size and position of [DVI3]. Push [DVI3]
button in Preview area, the button light is on, and the
image can be edited, push [SCALE] button to set the
size.
3. Choose the input signal in Preview area.
4. Push [DSK] button, and start the DSK function.
Rotate the knob and choose <PRESET>, press the
knob to confirm, choose the preset mode of DVI3, for
example, WhOnBk2, press the knob to confirm.
5. Push [SAVE] button, and save the above settings.
How to Set up the Screen Parameter
Push MENU button, rotate the knob and choose
[OUTPUT FORMAT] option.
The setting of screen is according to the LED size, and
is applied to single image. For example, the LED size
is1408 x 832.
First, choose the resolution that most close to 1408 x
832 or larger than 1408 x 832, which ensures that all
image can displayed on the LED screen. Push [MENU]
button, OLED show the menu, rotate the knob and
choose [SCREEN PARAMETERS], push the knob to
confirm.
Then set H size and V size for 1408 and 832, and need
not set the position if image is not migration. If quality
image distorts by mistake in improper operation, it can
be initialized operation to recover factory setting.
VSP 5360 Quick Start
Version 1.1
Page 3 of 4
Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C
Tel: [phone] Fax:[phone]
Email: [e-mail] http://www.rgblink.cn
How to Crop the Image
1. Push [Crop/Zoom] button, the button lights, user can
crop the image.
2. Rotate the knob to crop H LEFT, V UP, H RIGHT, V
DOWN of the image according to user’s need.
3. If quality image distorts by mistake in improper
operation, it can be initialized operation to recover
factory setting.
4. Push any other button, [Crop/Zoom] button light is
off, and close crop the image function.
How to Realize LOGO Capture
1. Push [MENU] button and enter the menu, rotate the
knob, and select [LOGO CAPTURE] option.
2. Choose the input source.
3. Freeze image, when capture LOGO, the program
image should be frozen.
4. Set the LOGO horizontal position, vertical position,
horizontal size and vertical size.
5. Save the image to LOGO1 or LOGO2.
6. Start to capture LOGO.
How to Save the Parameter
Push SAVE button, the key lights, OLED shows
related save information, operate according to the
prompt information.
Some of the number buttons 0-12 in PRE area are on,
and some flash. The buttons on mean there are no save
information, and button flashes will be overwrite. Push
the button on to save, OLED shows save is successful.
How to Load the Saved Parameter
Push LOAD button, the key lights, OLED shows
related load information, operate according to the
prompt information.
Some of the number buttons 0-12 in PRE area are on,
some flash and some are off. The button on mean is
ready for recall. Push the button on to load, OLED
shows recall is successful.
Display blinks
Check if preview output is normal: Get a monitor
with VGA or DVI port and connect to the device output
port, check if the monitor displays normally. If no
flashes, check if DVI output plugs tight or change the
DVI cable that connects sending card, if the monitor
blinks, please check if input signal, input connecting
cable and input port are normal.
Assure there are output signals: Get a monitor with
VGA or DVI port, connect it to device output port, see
if the monitor can display normally. If unnormal,
check if the input signals are connected or if the output
cable contacts good. If normal, check if the sending
card works normally or change a sending card to test.
Display has no output image
Assure there are input signals: Check if the input
signal sources is normal, if normal, please check the
connection; If use PC DVI or VGA as signal source,
please set the display card to dual display or expanding
mode.
Display only shows part of the image
Scale the image：Push [Scale /Position] button in the
processor and knob to adjust the actual screen size of
the screen, including “H Size”, “V Size” and “Reset”.
Push the knob to confirm.
Display shows no bottom half part
Incorrect output resolution: Please make sure the
points of the screen width and height, choose the
resolution to be bigger than screen width via push
[MENU] button to find [OUTPUT FORMAT], and
push the knob to confirm.
Mega Systems Inc., US Distributor of RGBLink
www.megasystemsinc.com • [e-mail]
Toll Free: 866-460-MEGA • Local: 210-684-2600
5718 Kenwick St., San Antonio, TX 78238