Specification Sheet

Air
Accessories
RGPE Series
10
RETURN AIR CABINETS
A
IN. [mm]
FILTER SIZE
IN. [mm]
RXGR-C17B 17
1
/2 [445] (2) 12 x 16 [305 x 406]
RXGR-C21B
21
1
/4 [533]
(2) 20 x 16 [508 x 406]
RXGR-C24B 24
1
/2 [622] (2) 24 x 16 [610 x 406]
FILTER RACK FILTER SIZES† INCHES [mm]
MODEL
RGPE-
RXGF-CA
(SIDE)
05, 07*AMK
15
3
/
4 x 25
[400 x 635]
07*BRQ, 10
15
3
/4 x 25
[400 x 635]
12
15
3
/4 x 25
[400 x 635]
†Filter racks are shipped without filters.
Filters shipped with furnace may be used or a suitable 1" [25.4 mm] filter.
*Designates “E” or “N”.
THE RXGR-C24B MUST ONLY BE INSTALLED ON THE SIDE
OPPOSITE THE GAS AND ELECTRICAL CONNECTIONS.
WARNING: IMPORTANT NOTICE
A SOLID METAL BASE PLATE (SEE TABLE) MUST BE IN PLACE WHEN THE FURNACE IS
INSTALLED WITH SIDE AIR RETURN DUCTS. FAILURE TO INSTALL A BASE PLATE COULD
CAUSE PRODUCTS OF COMBUSTION TO BE CIRCULATED INTO THE LIVING SPACE AND
CREATE POTENTIALLY HAZARDOUS CONDITIONS.
FURNACE BASE
WIDTH
SOLID BOTTOM BASE
PLATE SIZE
IN. [mm]
KIT NO. PLATE NO.
IN. [mm]
17
1
/2 [445] RXGB-D17 AE-61874-02 15
1
/8 x 23
9
/16 [384 x 598]
21
1
/2 [533] RXGB-D21 AE-61874-03 18
5
/8 x 23
9
/16 [473 x 598]
24
1
/2 [622] RXGB-D24 AE-61874-04 25
5
/8 x 23
9
/16 [651 x 598]
RXGW-B01 CHIMNEY ADAPTER
See Installation Instructions for application limitations.
FOR HIGH ALTITUDES:
HIGH ALTITUDE KIT: RXGY-F13 (for all models)
NOTE: High altitude kits do NOT include additional burner orifices. If
a burner orifice change is necessary, they must be ordered through
PROSTOCK
®
. See Installation instructions for more information.
CAUTION: Always follow National Fuel Gas Code (NFGC) guidelines when
converting furnaces for high altitudes.
For all installations above 2000 ft. the burner orifice size needs to be
recalculated and verified. A burner orifice change may still be required.
See Installation Instructions for more information.
NOTE: For Canadian installations only, an optional derate (manifold gas
pressure reduction) method may be used to adjust the furnace for
altitude. See Installation Instructions for more information. This
optional method may NOT be used for U.S. installations.
(U.S. Models—Kit packaged with furnace. Requires field installation).
[ ] Designates Metric Conversions
INTERNAL FILTER RACK FOR BOTTOM
OR SIDE RETURN: RXGF-DA*
*Filters available through PROSTOCK
®
.
SIDE RETURN FILTER RACK: RXGF-CA
BOTTOM RETURN FILTER RACK FOR
UPFLOW APPLICATION: RXGF-CB
ACCESSORY RETURN
AIR CABINETS
Return Air Cabinets may
be installed on either side
application except RXGR-C24B
(side application must be
on side opposite gas and
electrical connections).
RXPF-F01 and F02
FOSSIL FUEL KIT—is for use with Rheem Heat Pumps and warm air
furnaces. RXPF-F02 also meets TVA requirements.
RETURN AIR CABINETS