Specification

PRINTED IN U.S.A. 10/16 WP FORM NO. RR102CE-5 Rev. 11
Water
INTEGRATED HOME COMFORT
Commercial Electric
PowerPack ASME Water Heaters
I N TEGR ATED AIR & WATER
INTEGRATED HOME COMFORT
Features & Benefits
• Delivers 90-190° F water
• Installs close to fixtures, eliminating
the wait for hot water
• Long-life ASME tank design:
Proprietary steel formulation with
high temperature porcelain enamel
maximizes corrosion resistance
• Lifeguard
™
heating elements: Resist
corrosion and burnout; separate
screw-in type elements feature a
stainless steel outer sheath of Incoloy
®
840, which surrounds the Nichrome
wire filament
• Immersion thermostat
• Water Connections: Hot outlet and
cold inlet are 3/4" NPT plastic lined
nipples which prevent excessive
turbulence of heated water and results
in optimum tank draw
Efficiency
• 98 Percent maximum recovery
efficiency
• Minimal heat loss: majority of the tank
surface area is insulated with 2-1/2"
rigid polyurethane foam insulation
System Sentinel
Exclusive diagnostic system with
glowing LEDs that verify heating
element operation. LEDs pin point
the exact location of functioning or
non-functioning heating elements
Capacity & Dimensions
• 13 Gallons: 28-1/2" tall
• 19.9 Gallons: 36-1/2" tall
• 30 Gallons: 49-1/4" tall
• 40 Gallons: 53-3/4" tall
Plus…
• Integral fusing on each element
• Two magnesium anode rods for long
life and corrosion resistance
• Full-flow, full-port, brass drain valve
• Temperature and pressure relief valve,
factory installed
• Electrical Connections: Pre-wired,
accessible control box with multiple
knock-outs on side in size selections
to match the National Electric Code.
Sizes range from 1/2" to 2". A ground-
ing screw is provided for attaching an
equipment grounding conductor
• Single Panel Control Box with Hinged
Door: Provides immediate access
to all electrical components and
elements
•
Terminal Block: All models are
equipped with U.L. listed terminal
blocks for simplicity of installation.
The terminal block will accept either
copper or aluminum field connect wire
• 120 Volt Control Circuit: All units
are furnished with a fused 120 volt
control circuit. This circuit is created
by an internal multi-tap transformer of
unique design that has four (4) taps
for the primary voltages, 208, 240,
277 and 480
Warranty
3-Year limited tank warranty against
tank leaks, 1-year limited parts warranty
See Commercial Warranty Certificate for
complete information
PowerPack ASME series commercial electric
water heaters deliver a maximum of 190° F water
and are designed for general use or point-of-use
Rheem
PowerPack ASME
13, 19.9, 30 and 40-Gallon
Capacity Models
3 kW through 36 kW
Voltages: 208, 240, 277, 480
Field Convertible
Single Phase & Factory Wired
Three Phase
Electric
NEW UL Approved
Electric Conversion Kits*
• Provides an easy way to convert
standard models to different
wattages, volt or phase depending
on installation requirements
• Kits are designed for ELD(S)
models in all gallon capacities
• All parts needed for the electric
conversion are included with
Rheem electric conversion kits
• Rheem electric conversion
kits provide convenience for
contractors, plumbers and installers
which saves time and money
* Not available in Canada.
Efficiency | In accordance with ANSI test procedures,
these models tested below the maximum allowable
standby loss levels of current ASHRAE Standards
(Part of the Federally mandated Energy Policy Act
(EPact)). Also exceeds energy efficiency codes of all
states including California Energy Commission (CEC).
Safety and Construction | These products are
design certified by Underwriters Laboratories (UL)
to meet UL standard 1453 as electric booster and
commercial storage tank water heaters. All models are
North Carolina and Massachusetts code compliant.
Certified for 160 PSI maximum working pressure.
ASME Construction | Standard on E12A, E20A,
E30A, and E40A models.