Specification

Triton Gas Water Heaters
3
MAX. VENT LENGTH (Eq. Ft.)
PIPE DIAMETER
MODEL NUMBER
2" (5 cm) 3" (8 cm) 4" (10 cm) 6" (15 cm)
INLET OUTLET INLET OUTLET INLET OUTLET INLET OUTLET
GHE80SU-130(A) 20 35 60 75 120 135 X X
GHE80SU-160(A) 20 35 60 75 120 135 X X
GHE80SU-200(A) 20 35 60 75 120 135 X X
GHE80SU-300(A) X X 60 75 120 135 120 135
GHE100SU-130(A) 20 35 60 75 120 135 X X
GHE100SU-160(A) 20 35 60 75 120 135 X X
GHE100SU-200(A) 20 35 60 75 120 135 X X
GHE100SU-250(A) X X 60 75 120 135 X X
GHE100SU-300(A) X X 60 75 120 135 120 135
GHE100SU-400(A) X X 50 65 70 85 120 135
MAX. VENT LENGTH (Eq. Ft.)
PIPE DIAMETER
MODEL NUMBER
2" (5 cm) 3" (8 cm) 4" (10 cm) 6" (15 cm)
INLET OUTLET INLET OUTLET INLET OUTLET INLET OUTLET
GHE80SU-130(A) – 35 – 135 – 185 – X
GHE80SU-160(A) – 35 – 135 – 185 – X
GHE80SU-200(A) – 35 – 135 – 185 – X
GHE80SU-300(A) – X – 135 – 145 – 120
GHE100SU-130(A) – 35 – 135 – 185 – X
GHE100SU-160(A) – 35 – 135 – 185 – X
GHE100SU-200(A) – 35 – 135 – 185 – X
GHE100SU-250(A) – X – 135 – 185 – 120
GHE100SU-300(A) – X – 135 – 185 120 120
GHE100SU-400(A) – X – 65 – 100 120 135
VENTING OPTIONS
POWER
DIRECT VENT
POWER VENT
For each 90° elbow, reduce pipe length by five (5) feet.
For each 45° elbow, reduce pipe length by two and a half (2.5) feet.
Note: Vent pipe size should not be mixed for venting these units.
Use same diameter pipe for all venting of the unit.
3" Concentric = 60 ft. in, 75 ft. out
4" Concentric = 120 ft. in, 135 ft. out
See use and care manual for venting details.
Vents with Polypropylene, ABS, CPVC or PVC.
NOTE: For Canadian installations, please use Polypropolene, ULC S636 PVC or CPVC.
Efficiency | All models tested according to ANSI test procedures, and meet or exceed the thermal efficiency and standby loss requirements of ASHRAE standard (EPact).
Also exceeds energy efficiency codes of all states including California Energy Commission (CEC).
Safety and Construction | Design certified by CSA: For operation at 185 degrees; meets all safety and construction requirement of ANSI Z21.10.3; as an automatic storage or
instantaneous water heater; as an automatic circulating tank water heater; and for operation on combustible floors and in alcove installations. Certified for 150 PSI maximum
working pressure (160 PSI for ASME models).
Optional Construction | ASME construction is available on designated models. UL Sanitation (NSF5) compliant models are available when equipped with optional seal kit
(Part No. AS42690).