R-Series R500 R600 R700 R800 R800C O w ner’s Ma nua l
Contents IMPORTANT SAFETY INSTRUCTIONS Polarization instructions Thermal fuse protection Description of the vacuum Assembly & Operation Attaching the handle On/Off switch Handle adjustments Replacing vacuum bag Replacing secondary and post filters Removing and reinstalling bottom plate Replacing headlight bulb Replacing agitator belt Unclogging nozzle and hose Full bag indicator light 2 3 4 5 6 7 7 8 9 10 11 11 12 13 Tools FastTask™ cleaning tools Optional cleani
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE he manufacturer cannot accept responsibility for damage WARNING: Tcaused when the appliance is not used according to the instructions, or for uses other than those for which it was intended. To reduce the risk of fire, electric shock or injury: •D o not put any object into openings.
Polarization instructions Power Cord - 2-Wire Polarized Household models R500, R600, R700 & R800 To reduce the risk of electric shock this product is equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug.
Thermal fuse protection Your Riccar vacuum cleaner comes equipped with a Manual Reset Thermal Fuse Protector. This thermal protector is designed to protect your vacuum cleaner from overheating due to a restriction in airflow (i.e. clogged hose, operating the vacuum without a bag). Should this situation occur, the thermal fuse protector will safely shut off the vacuum cleaner to avoid any potential damage.
Description of the vacuum Handle grip On/Off switch (Models R600, R700, R800, R800C) Cord clip Hose storage hook (Models R500, R600, R800, R800C) Power cord Stretch hose Carrying handle Cord storage hooks On/Off switch (Model R500) Telescopic wand Full bag indicator light (Models R700, R800 and R800C) Bag compartment cover Suction control dial Crevice tool Upholstery/ dusting tool Headlight Thermal fuse reset button Furniture guard Foot pedal release Self-adjusting nozzle Riccar Replacement Parts
Operation Attaching the handle The vacuum cleaner and the handle are packed separately. 1. After first removing the handle screw [Fig. 1], position the handle behind the vacuum cleaner and level with the top of the unit. Hold the power cord down and away from the vacuum while the handle is being attached [Fig. 2]. Make sure that the switch on the handle is positioned toward the front of the vacuum cleaner. Fig. 1 2.
Operation On/Off switch 1. To start the vacuum cleaner, flip the ON/OFF switch (located on the handle on Models R600, R700, R800 and R800C or on the side of bag compartment on Model R500) to the ON position as indicated by “|” on the switch [Figs. 5 and 6]. 2. T o stop the vacuum cleaner, flip the ON/OFF switch to the OFF position as indicated by “O” on the switch. Fig. 5 3. T urn the vacuum cleaner off before unplugging from electrical outlet. Fig.
Operation Replacing vacuum bag Genuine Riccar vacuum bags should be used for best performance and air filtration. Always operate the vacuum cleaner with a vacuum bag installed. NOTE: If secondary or post filters need to be replaced, see page 9 before replacing the vacuum bag. Fig. 10 1. R emove the used vacuum bag by pulling bag collar off the bag holder [Fig. 10]. Do not re-use filled vacuum bags. 2. A ttach the new vacuum bag onto the bag holder. 3.
Operation Replacing secondary filter The secondary filter protects the motor from dust and dirt. Before installing a new vacuum bag, check the filter. Accumulated dirt in the bag compartment will be collected on this filter and may restrict motor performance when the filter becomes dirty. 1. R emove the vacuum bag to access the secondary filter. Fig. 12 2. R emove secondary filter from bottom of bag compartment [Fig. 12]. 3. T he secondary filter can be washed or replaced.
Operation Removing and reinstalling bottom plate CAUTION: Disconnect the vacuum cleaner from the electrical outlet before removing the bottom plate. 1. Depress handle release pedal twice and place the vacuum cleaner in the low position. 2. T urn vacuum cleaner over, exposing the underside [Fig. 15]. Fig. 15 3. Slide locking latch to the right [Fig. 16]. 4. P ress tabs inward on each side [Fig. 17] and pull bottom plate off. 5.
Operation Replacing headlight bulb AUTION: Disconnect the vacuum cleaner from the C electrical outlet before replacing bulb. 1. R emove bottom plate (See “Removing and reinstalling bottom plate”). 2. R emove the headlight bracket by pulling upward on bracket [Fig. 19]. To remove the light bulb, pull straight out of socket. To install new bulb, simply push bulb straight into socket for a secure fit. Reinsert bracket back into nozzle. Fig. 19 3.
Operation Unclogging nozzle and hose CAUTION: Disconnect the vacuum cleaner from the electrical outlet before cleaning nozzle housing. The nozzle hose, located on the back of the vacuum, carries the dirt from the nozzle to the vacuum bag. The hose also functions as the attachment cleaning hose. First check to see that a bag is installed or that the bag has not broken open. Fig. 23 If the hose should become clogged: 1. P ull out and turn the lid of the cleaning attachment opening.
Operation Full bag indicator light Models R700, R800 and R800C The warning light is located on top of the bag compartment (see Fig. 26). The light will trigger if the vacuum bag is full or if there is a clog in the vacuum cleaner. If the light indicator turns on, check the vacuum bag. If it is not full, check the vacuum cleaner for clogs by inspecting the agitator area (see “Removing and re-installing bottom plate”), hose and/or attachment inlet.
Tools FastTask™ cleaning tools (Models R500, R600, R800 and R800C) Select models are equipped with FastTask™ cleaning tools which include a combination upholstery/dusting tool, crevice tool and stretch hose. 1. R emove the telescopic wand from the body of the vacuum [Fig. 27]. Unlock wand collar (located on end of wand) [Fig. 28], extend wand and re-lock the wand collar. NOTE: Wand collar locking rotation is marked with arrows on wand. Wand collar lock and unlock functions require only 1/2 turn of collar.
Tools Optional cleaning tools All Riccar upright vacuum cleaners offer an attachment port that enables you to insert optional cleaning tools (available through your Riccar Retailer). Should you have carpeted stairs, for example, it is highly recommended to use one of the two kits pictured, since each offers either a 12- or 15-foot hose for safe stair cleaning. These kits are effective overall cleaning tools to address some of the hard to reach areas of your home or car.
Owner’s information (keep this for your records) The model and serial number of this product may be found on the back side of the unit. You should note the model and serial number of your unit in the spaces provided below, and retain this book as a permanent record of your purchase.
Warranty What is Covered: This warranty covers any defects in material and workmanship in your new Riccar vacuum. How Long Coverage Lasts: Warranty coverage for Riccar R-Series household model vacuums lasts three years and one year for R-Series commercial model vacuums. Household models used commercially are only warranted for 90 days. What is Not Covered: • Damage to the vacuum which occurs from neglect, abuse, alterations, accident, misuse or improper maintenance.
www.riccar.
