Owner’s Manual Model RSL1 RSL2 RSL2C ™ Vacuum Cleaner Thank you for purchasing our product. To ensure you get the best results from your SupraLite vacuum cleaner, please read this manual first. This manual should be kept for future reference. To locate your nearest Authorized Riccar Dealer for sales or service, please visit our website at www.riccar.
KEY REPLACEMENT PARTS Genuine SupraLite Vacuum Filter Bags: RSL-6 Genuine SupraLite Vacuum Agitator Belt: B014-0814
TABLE OF CONTENTS Getting Started: • Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 • Wire and grounding instructions . . . . . . . . . . . . . . . . . . . . . . . . . 3 • Assembling the vacuum cleaner . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Vacuum Features: • On/off switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 • Edge cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE When using an electrical appliance, basic precautions should always be followed. WARNING – 1. 2. 3. 4. 5. 6. 7 8. To reduce the risk of fire, electric shock or injury: Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. WARNING: ELECTRIC SHOCK COULD OCCUR IF USED OUTDOORS OR ON WET SURFACES. Do not allow to be used as a toy.
POLARIZATION INSTRUCTIONS – HOUSEHOLD MODELS Models RSL1 and RSL2 To reduce the risk of electric shock, this appliance is equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact a qualified electrician to replace the obsolete outlet.
ASSEMBLING THE VACUUM IMPORTANT NOTE: Under no circumstances should you plug in the vacuum cleaner prior to complete assembly. Cloth Bag Nozzle Power cord Handles 1 The vacuum cleaner handle is packed as a separate component that requires assembly. VACUUM ASSEMBLY PROCEDURE 2 4 Installing the handle: 1. Release the handle bracket from the handle tube by removing the two screws (diagram 1). 2. Place handle onto the handle tube, aligning holes with pegs (diagram 2).
ASSEMBLING 3. Place the handle bracket back into position (diagram 3). 4. Secure with two screws removed in step 1. Positioning the power cord: (Models RSL1 only.) 1. Loosen, but do not remove, the screw holding the upper cord hook (diagram 4). 2. Position the cord between the cord hook and the vacuum tube (diagram 5). Re-tighten the screw. 3. Once the cord is secured by the cord hook, proceed with wrapping the cord.
ON / OFF SWITCH 6 6A NOTE: Your vacuum cleaner will either have the on/off button on the base of the unit (see diagram 6) or on the vacuum handle (see diagram 6A). Please note the type of vacuum cleaner you are using when starting or stopping the machine. On/Off switch on base: Locate the switch on the back side of the nozzle to the left of the handle tube. Simply press the switch with your foot to turn the machine on or off. On/Off switch on handle: Locate the switch on the top of the vacuum handle.
HOW TO CHANGE THE 1. Unzip outer cloth bag (diagram 7). 2. Remove used bag by pressing the bag holder tab and pulling bag off vacuum (diagram 8). Discard used bag. 3. To install new bag, position the bottom of the bag collar into the bag collar holder (diagram 9). 4. Push the top of the bag collar inward until the collar “snaps” into place (diagram 10). 4. Zip the outer cloth bag closed.
HOW TO REMOVE / INSTALL THE BOTTOM PLATE 11 CAUTION: First, disconnect the vacuum cleaner from the electrical outlet. To remove bottom plate: 1. After unplugging the power cord, turn the vacuum cleaner over, exposing the underside. 2. Press the two holding tabs inward (diagram 11) releasing the bottom plate. Remove the bottom plate. 12 To install bottom plate: 1. Install bottom plate, making sure bottom plate hinges are in place before setting the plate (diagram 12). 2.
HOW TO CHANGE THE BELT 13 CAUTION: First, disconnect the vacuum cleaner from the electrical outlet. 1. Turn the unit over and remove the bottom plate (see "How to Remove Bottom Plate"). 2. Remove the brush roll and the worn or broken belt from the brush roll pulley and the motor drive shaft (diagram 13). 3. Loop the new belt around the motor drive shaft and the brush roll (diagram 14). 4. Reinstall the brush roll back into the housing.
HOW TO REPLACE Nozzle screws Nozzle Tabs 18 19 10 HEADLIGHT BULB WARNING: To reduce the risk of electric 16 17 THE shock and injury from moving parts, unplug vacuum before cleaning or servicing. 1. First remove the nozzle housing. Turn the unit over to expose the underside. Locate the two main nozzle screws (diagram 16) and remove both. Turn the unit right side up. Locate the two nozzle tabs on the back of the unit (diagram 17) and unlatch the nozzle housing.
HOW TO RESET THE Your vacuum features a circuit breaker to protect the machine against damage due to a surge in the electrical current. Electrical surging can be a result of, though not limited to, a jammed brush roll (i.e. vacuuming up a sock or throw rug) or a jammed motor fan. Should your vacuum cleaner experience a jammed brush roll with the circuit breaker tripping, first press the on/off button to the off position and unplug the unit.
FOR BEST PERFORMANCE • Keep machine clean and in good operating condition. • Change filter bags as recommended to maximize optimal cleaning efficiency. • Always use genuine filter bags and replacement parts. Use of other products may result in poor cleaning performance and potential vacuum cleaner damage and may void vacuum warranty. Genuine filtration products are designed for maximum cleaning performance. • Have machine checked periodically by your Authorized Dealer.
RICCAR VACUUM CLEANER LIMITED WARRANTY Riccar’s Limited Warranty ™ 2-year limited HOUSEHOLD warranty – 1-year limited COMMERCIAL warranty Riccar America will repair or exchange par ts for your Riccar vacuum cleaner in the event of a manufacturing defect as follows: PARTS: HOUSEHOLD USE: New or comparable rebuilt parts are warranted for two years (fan for one year) after original purchase.
Item IBRSL1B (B503-1200C)