User's Manual
Lunar Wireless Headphone
Package Contents:
Bluetooth headphone x1
Charging cable x1
User’s Manual x1
Button Description:
ON/OFF Switch/Pause/Play Music
Short press for Next song / long press increase volume
Short press for Previous song / long press reduce volume
How To Use:
• Power on: Press the center key “ ” three seconds when it is off.The blue LED
light will be on. A voice will prompt “bluetooth mode” and the blue LED light will flash to
pair successfully.
• Pairing: Activate the bluetooth function on your phone within range and select
“BTOOTH HEADPHON” from the list shown.When the blue LED stops flashing, it has
paired successfully and you will hear a “beep”. The blue LED will flash slowly when
playing music.
• Play/Pause: When it is playing, press the center key “ ” to pause, then press the
center key “ ” again to play.
• Volume up: Hold down the “+” to increase the volume.
• Volume down: Hold down the “-” to decrease the volume.
• Previous song: Press “+” once to play the previous song.
• Next song: Press “-” once to play the next song.
• Power off: When headphone is standby or operating, press the center key “ ” 3
seconds to shut down the headphone (voice prompt “power off”).
• IMPORTANT: Whilst using the 3.5mm audio jack cable the bluetooth function buttons
have no function. Use your chosen device function buttons.
Note: Use the mobile phone to answer a phone call, the Bluetooth Headphone has
NO answer incoming call function.
FCC statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
USB Plug Micro USB Plug
•
Charge and operate only as indicated in this manual, as improper use may
result in damage to the product or injury.
• To avoid risk of shock or injury, do not dismantle the device or insert any
objects into the Heaphone.
• To avoid electronic interference and/or compatible conflicts, turn off the
product in any facilities where posted notices instruct you to do so.
• Do not pull the Heaphone charging cable. Damage may result to the cable.
• Keep out of reach of children. This is not a toy.
• Avoid exposure to moisture, liquids, heat, flame and high voltage equipment.
• Retain these instructions as they contain important information.
• Do not short circuit the input terminals of the Heaphone.
• Do not drop, place heavy weight or allow heavy impact to the Heaphone.
• Do not heat or apply heat or dispose of the in fire.
• Do not use the product while driving or crossing the road.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
FCC ID: 2AAJQGE00059
Distributed by Five Below Merchandising, Inc.
1818 Market Street, Suite 2000
Philadelphia, PA 19103
Made in China
Visit Us At: www.fivebelow.com
Keep All Relevant Information For Future Reference
User Manual
• Model Number: GE00059 MU01017
• Bluetooth Version: 4.2
• Rang: 33ft / 10 m
• Battery Capacity: 200 mAh
• Voltage: 3.7 V
• Working Time: 4-5 hours
• Charging Time: 2-3 hours
• Charging Way: USB DC 5V
• Frequency Response: 20Hz-20KHz
FAQ:
1) Why can’t I start my Bluetooth headphone?
Answer: Please ensure that the headphone is fully charged for your first use.
2) Why won’t sound come out of the headphones?
Answer: Check whether the playback device and the Bluetooth headphone are
successfully established. If the audio device is not properly connected,
please reconnect. Please also adjust your mobile phone or Bluetooth headphone
volume to a suitable volume level.
3) Why can’t I find this headphone in my bluetooth options?
Answer: Make sure the Bluetooth is in “visible mode”. If no pairing occurs, the
Bluetooth function will automatically shut off. Please reopen Bluetooth to
“visible mode”. If there is a program error, please reboot your phone, and if program
error is caused by your Bluetooth headphone, please restart the headphone.
•
•
•
“
”
：
“
”
：
“
”
：
Tips:
• Low voltage: LED light flash in blue.
• AUX Audio Interface: When an external audio cable is being used, Bluetooth
function is turned off.
• To Charge:
1. Insert the USB connector end of included cable (see packing list) into the USB jack
on the charger or USB port on the computer.
2. The indicator light will be red while charging.
3. When the headphone is fully charged, the indicator light will turn to blue from red.
Please unplug your charger from power source.
4. Please use qualified charger to recharge your headphone. If not, it may result in
damage or even explosion to it.
5. Repeated charging and discharging the earphone will lead to decreased battery
life over time, which is normal for rechargeable batteries.
6. You must charge the Bluetooth Heaphone if it has not been used for more than 6
months.
Technical Specifications:
+
-
WARNING:
WARNING:
Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.