VT 1503 – VT 1704 – VT 1904 TFT-LCD MONITOR WITH VGA & VIDEO 15” – 17” – 19” USER’S MANUAL Rev. 2.
CONTENTS 1. Introduction Page 2 Product Description……………………………………... Page 2 Package Contents………………………………………. Page 2 Product Features…………………………………….….. Page 2 Screen Cleaning Techniques…………………………… Page 2 Additional…………………………………………….…… Page 2 2. Control Functions Page 3 Function Selection…………………………………….... Page 4 Function Adjustments……………………………….….. Page 4 3. Installation………………………………………………. Page 9 4. Display Modes…………………………………….……. Page 9 5.
1. Introduction Product Description Congratulations on your purchase of the LCD monitor with VGA & Video Input out of our VT series. It incorporates high quality display into a small light-weighted module. It has power-saving capabilities and emits no radiation. You will certainly benefit from this monitor in lots of ways; to name some of them: comfort, safety, space-saving and environmental protection.
2. Power Use the type of power indicated on label. 3. Plugs DO NOT remove any of the prongs of the monitor’s three-pronged power plug. Disconnect the power plug from the AC outlet under following conditions: If you will not use it for an extended period time. When the power cord or plug is damaged or frayed. If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions.
Function Selection 1. Press the knob “MENU/SELECT” to show the OSD menu. Then use the “▲” and “▼” to select a function. Press the knob “AUTO/EXIT” to close the OSD menu. 2. With the knob “▲” and “▼”, you can adjust the speaker volume on the monitor. When you press the knop “▼”, the speakers are mute. Press the “▼” and then the speakers are active. When you press the knob “▲”, the speaker volume OSD is shown. You can increase or decrease the volume by pressing the “▲” and “▼”. 3.
Tint - Adjust the Tint level of the image Sharpness - Adjust the Sharpness level of the image Video Mode - Adjust the Video Mode for Normal/Nature/Cinema/Sport/Vivid Reset - Recall the factory setting of the Video menu.
VGA Contrast Brightness Sharpness - Adjust the difference in luminance between light and dark areas of the image. - Adjust the luminance level of the image.
User RGB - Adjusting R/G/B level of the image Image Auto Tune - Adjust geometry of the image automatically. Position - Adjust the vertical & horizontal position of the image. Phase - Adjust the horizontal sync phase of signal. Clocks - Adjust the horizontal sync size of signal. Reset - Recall the factory setting of the VGA menu. 3. Audio (Video & VGA) Volume - Adjust the speaker volume.
4.
3. Installation Unpacking Open the shipping carton and check the package contents. If any items are missing or damaged, contact us immediately. The package should include the following items: TFT LCD monitor 15-pin-mini-D-Sub/VGA signal cable Audio cable AC power cord AC/DC power adapter User’s manual Installing the Monitor This monitor is equipped with an auto sensing DC power adapter for voltage ranges of 100-240VAC, 60/50Hz. Follow these steps to install the monitor: 1.
5. Signal Connector Pin-outs To connect VGA, 8514A or IBM-compatible graphics adapters, use a 15 pin mini D-type male connector. 15-pin Mini D-type Male Connector Pin Assignment 1 Red Video 6 Red Ground 2 Green Video 7 Green Ground 3 Blue Video 8 Blue Ground 4 Ground 9 No Connection 5 No Connection 10 Sync Ground 11 Ground 12 Serial Data/I/O 13 H. Sync 14 V. Sync 15 Serial Clock Input 6. Power Saving Features When the power saving is active, the power indicator LED will be from Green Light to Amber.
7. Product Specifications 7.1 Product specifications: 15inch Model LCD Panel Size Maximum viewable size 1503 15” 15 inch(38.
7.3 Product specifications: 19inch Model LCD Panel Size Maximum viewable size Video Input 1904 19” 19 inch (48.3cm) Analog:15-pin, D-sub connector x1 S-Video x1, RCA composite x1 Display area Power supply (Universal) Input voltage Consumption External controls 376mmx301mm(H×V) 12V DC / 3.
8. Windows setup For the best display quality, please set the monitor type in Windows.
For 800 ×600, please set to “SVGA 800 × 600 @ 60Hz” [12” Monitor] 9. Trouble Shooting 1) Power on but no picture → Make sure the VGA cable is tightly connected from the video output connector on the video card to the video input connector on the monitor. → Make sure you are using the standard power adapter coming with the monitor. → Check your video card if the driver is correctly installed. If there is no video signal from the video card, “NO INPUT SIGNAL” will show on the screen.
6) Residue image → If an image remains on the screen for an extended period of time, it may be imprinted in the screen and leave a residue image. It is characteristic of liquid crystal and is not malfunction or deterioration of the liquid crystal. The residue image will disappear after a period of time. It is recommended to set up the screen saver for your LCD monitor. 7) Out of Rang → The first thing you need to check is the screen resolution.
