Service manual

ManualsBrandsRicoh ManualsComputer equipmentG165

G165/G166/G167

G181/G183/G184

SERVICE MANUAL

003359MIU

CÓPIA NÃO CONTROLADA

Summary of content (300 pages)

PAGE 1
CÓPIA NÃO CONTROLADA G165/G166/G167 G181/G183/G184 SERVICE MANUAL 003359MIU CÓPIA NÃO CONTROLADA
PAGE 2
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 3
CÓPIA NÃO CONTROLADA G165/G166/G167 G181/G183/G184 SERVICE MANUAL CÓPIA NÃO CONTROLADA
PAGE 4
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 5
CÓPIA NÃO CONTROLADA G165/G166/G167 G181/G183/G184 SERVICE MANUAL 003359MIU CÓPIA NÃO CONTROLADA
PAGE 6
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 7
CÓPIA NÃO CONTROLADA It is the reader's responsibility when discussing the information contained within this document to maintain a level of confidentiality that is in the best interest of Ricoh Americas Corporation and its member companies. NO PART OF THIS DOCUMENT MAY BE REPRODUCED IN ANY FASHION AND DISTRIBUTED WITHOUT THE PRIOR PERMISSION OF RICOH AMERICAS CORPORATION.
PAGE 8
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 9
CÓPIA NÃO CONTROLADA WARNING The Service Manual contains information regarding service techniques, procedures, processes and spare parts of office equipment distributed by Ricoh Americas Corporation. Users of this manual should be either service trained or certified by successfully completing a Ricoh Technical Training Program.
PAGE 10
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 11
CÓPIA NÃO CONTROLADA LEGEND PRODUCT CODE G165 G166 G167 G181 G183 G184 LANIER SP C220N SP C221N SP C222DN SP C220S SP C221SF SP C222SF COMPANY RICOH SP C220N SP C221N SP C222DN SP C220S SP C221SF SP C222SF SAVIN SP C220N SP C221N SP C222DN SP C220S SP C221SF SP C222SF DOCUMENTATION HISTORY REV. NO.
PAGE 12
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 13
CÓPIA NÃO CONTROLADA G165/G166/G167/G181/G183/G184 TABLE OF CONTENTS INSTALLATION 1. INSTALLATION .......................................................................1-1 1.1 INSTALLATION REQUIREMENTS.......................................................1-1 1.1.1 ENVIRONMENT ..........................................................................1-1 1.1.2 MACHINE LEVEL ........................................................................1-1 1.1.3 MACHINE SPACE REQUIREMENT .........................
PAGE 14
CÓPIA NÃO CONTROLADA 3.4 LASER OPTICS ....................................................................................3-7 3.4.1 CAUTION DECAL LOCATIONS ..................................................3-7 3.4.2 LASER OPTICS HOUSING UNIT................................................3-8 After replacing the laser optics housing unit ..................................3-11 3.5 AIO CARTRIDGE................................................................................3-12 3.5.
PAGE 15
CÓPIA NÃO CONTROLADA 3.10.1 PAPER EXIT ROLLER .........................................................3-40 When reinstalling the paper exit roller ...........................................3-41 3.10.2 PAPER EXIT SENSOR ........................................................3-42 3.11 ELECTRICAL COMPONENTS......................................................3-43 3.11.1 CONTROLLER BOARD .......................................................3-43 GDI/ PCL Controller Board (Printer Model) ..................
PAGE 16
CÓPIA NÃO CONTROLADA Rev. 07/2008 3.12.11 ADF FEED SENSOR ........................................................3-72 3.12.12 ADF DRIVE BOARD .........................................................3-73 3.13 SCANNER.....................................................................................3-74 3.13.1 SCANNER UNIT ..................................................................3-74 3.13.2 SCANNER TOP COVER......................................................3-76 3.13.3 SCANNER CARRIAGE UNIT.
PAGE 17
CÓPIA NÃO CONTROLADA SERVICE TABLES 5. SERVICE TABLES...................................................................5-1 5.1 SERVICE PROGRAM...........................................................................5-1 5.1.1 OVERVIEW..................................................................................5-1 5.2 SMART ORGANIZING MONITOR (PRINTER MODEL) .......................5-2 5.2.1 OVERVIEW..................................................................................5-2 5.2.
PAGE 18
CÓPIA NÃO CONTROLADA Engine Firmware ...........................................................................5-53 5.4.2 MF MODEL ................................................................................5-54 Checking the Machine Firmware Version ......................................5-54 Updating the Controller Firmware..................................................5-54 Updating the Engine Firmware ......................................................5-56 5.4.3 BOOT LOADER FIRMWARE............
PAGE 19
CÓPIA NÃO CONTROLADA 6.4.6 DEVELOPMENT MECHANISM .................................................6-26 6.4.7 TONER NEAR END AND END DETECTION ............................6-26 Toner Near End.............................................................................6-26 Toner End......................................................................................6-26 6.5 PAPER FEED .....................................................................................6-27 6.5.1 OVERVIEW.....................
PAGE 20
CÓPIA NÃO CONTROLADA 6.8 CONTROLLER....................................................................................6-45 6.8.1 OVERVIEW................................................................................6-45 Controller: Printer model (G165/G166/G167) ................................6-45 Controller: MF model (G181/G183/G184) .....................................6-48 6.9 ADF.....................................................................................................6-51 6.9.1 OVERVIEW.
PAGE 21
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 22
CÓPIA NÃO CONTROLADA REPLACEMENT AND ADJUSTMENT TROUBLESHOOTING DETAILED DESCRIPTIONS TAB POSITION 8 TAB POSITION 7 SPECIFICATIONS TAB POSITION 6 TAB POSITION 5 SERVICE TABLES TAB POSITION 3 Paper Feed Unit TK1010 (G849) TAB POSITION 4 PREVENTIVE MAINTENANCE TAB POSITION 2 TAB POSITION 1 INSTALLATION CÓPIA NÃO CONTROLADA
PAGE 23
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 24
CÓPIA NÃO CONTROLADA Read This First Safety Notices Important Safety Notices Prevention of Physical Injury 1. Before disassembling or assembling parts of the printer and peripherals, make sure that the printer power cord is unplugged. 2. The wall outlet should be near the printer and easily accessible. 3. If any adjustment or operation check has to be made with exterior covers off or open while the main switch is turned on, keep hands away from electrified or mechanically driven components. 4.
PAGE 25
CÓPIA NÃO CONTROLADA Safety and Ecological Notes for Disposal 1. Do not incinerate toner bottles or used toner. Toner dust may ignite suddenly when exposed to an open flame. 2. Dispose of used toner, the maintenance unit which includes developer or the organic photoconductor in accordance with local regulations. (These are non-toxic supplies.) 3. Dispose of replaced parts in accordance with local regulations.
PAGE 26
CÓPIA NÃO CONTROLADA WARNING: Turn off the main switch before attempting any of the procedures in the Laser Optics Housing Unit section. Laser beams can seriously damage your eyes. CAUTION MARKING: Symbols, Abbreviations and Trademarks This manual uses several symbols and abbreviations.
PAGE 27
CÓPIA NÃO CONTROLADA Trademarks Microsoft®, Windows®, and MS-DOS® are registered trademarks of Microsoft Corporation in the United States and /or other countries. PostScript® is a registered trademark of Adobe Systems, Incorporated. PCL® is a registered trademark of Hewlett-Packard Company. Ethernet® is a registered trademark of Xerox Corporation. PowerPC® is a registered trademark of International Business Machines Corporation.
PAGE 28
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 29
CÓPIA NÃO CONTROLADA INSTALLATION INSTALLATION REVISION HISTORY Page Date Added/Updated/New None CÓPIA NÃO CONTROLADA
PAGE 30
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 31
CÓPIA NÃO CONTROLADA Installation Installation Requirements 1. INSTALLATION 1.1 INSTALLATION REQUIREMENTS 1.1.1 ENVIRONMENT 1. Temperature Range: 10°C to 32°C (50°F to 89.6°F) 2. Humidity Range: 15% to 80% RH 3. Ambient Illumination: Less than 2,000 lux (do not expose to direct sunlight) 4. Ventilation: 3 times/hr/person 5. Do not put the machine in areas that get sudden temperature changes.
PAGE 32
CÓPIA NÃO CONTROLADA Installation Requirements 1.1.3 MACHINE SPACE REQUIREMENT Put the machine near the power source with these clearances: Printer Model Left side: Over 20 cm (7.9") Rear: Over 10 cm (4") Right side: Over 10 cm (4") Front: Over 70 cm (27.5") MF Model Left side: Over 20 cm (7.9") Rear: Over 20 cm (7.9") Right side: Over 10 cm (4") Front: Over 70 cm (27.5") Top: Over 24 cm (9.
PAGE 33
CÓPIA NÃO CONTROLADA Installation Installation Requirements 1.1.4 POWER REQUIREMENTS Make sure that the plug is tightly in the outlet. Avoid multi-wiring. Make sure that you ground the machine. Input voltage level 120 V, 60 Hz: More than 11 A (for North America) 220 V to 240 V, 50 Hz/60 Hz: More than 6 A (for Europe/ Asia) Permitted voltage fluctuation: 10% Do not set anything on the power cord. 1.1.
PAGE 34
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 35
CÓPIA NÃO CONTROLADA PREVENTIVE MAINTENANCE PREVENTIVE MAINTENANCE REVISION HISTORY Page Date Added/Updated/New None CÓPIA NÃO CONTROLADA
PAGE 36
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 37
CÓPIA NÃO CONTROLADA Preventive Maintenance 2. PREVENTIVE MAINTENANCE Preventive Maintenance 2.1 PREVENTIVE MAINTENANCE 2.1.1 USER REPLACEABLE ITEMS Item Print Cartridge (AIO) Waste Toner Bottle Yield Approx. 2 k prints/cartridge Approx. 25 k prints/bottle (See condition 4) Condition: 1. An A4 (8.5"x11")/ 5% chart is used to measure the above yield. 2. The condition is standard temperature and humidity. 3. These yield values may change depending on the circumstances and printing conditions. 4.
PAGE 38
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 39
CÓPIA NÃO CONTROLADA REPLACEMENT & ADJUSTMENT REPLACEMENT & ADJUSTMENT REVISION HISTORY Page Date Added/Updated/New 7 08/24/2009 Add IMPORTANT message to refer to TSB - 026 11 08/24/2009 Add IMPORTANT message to refer to TSB - 026 17 ~ 18 08/11/2008 Image Transfer Belt Removal – Simplified Procedure CÓPIA NÃO CONTROLADA
PAGE 40
CÓPIA NÃO CONTROLADA G165/G166/G167/G181/G183/G184 4 CÓPIA NÃO CONTROLADA SM
PAGE 41
CÓPIA NÃO CONTROLADA Before You Start 3. REPLACEMENT AND ADJUSTMENT 3.1 BEFORE YOU START If there are printer jobs in the machine, print out all jobs in the printer buffer. Turn off the main power switch and unplug the machine before you do the Replacement Adjustment procedures in this section.
PAGE 42
CÓPIA NÃO CONTROLADA Special Tools 3.2 SPECIAL TOOLS PC: Windows 2000/XP/Vista, Windows Server 2003/2003 R2, or Mac OS X.
PAGE 43
CÓPIA NÃO CONTROLADA Exterior Covers 3.3 EXTERIOR COVERS Turn off the main power switch and unplug the printer before you do the procedures in this section. Replacement Adjustment 3.3.1 REAR COVER 1. Rear tray cover [A] 2.
PAGE 44
CÓPIA NÃO CONTROLADA Exterior Covers 3.3.2 OPERATION PANEL 1. Open the top cover [A]. 2. Open the front cover [B]. 3. Front harness cover [C] ( x 1) 4.
PAGE 45
CÓPIA NÃO CONTROLADA Exterior Covers 3.3.3 RIGHT COVER Rear cover ( Rear Cover) 2. Operation panel ( Operation Panel) 1. Right cover [A] ( x 4) Replacement Adjustment 1. Top front screw: M3x6, others: M4x6 3.3.4 LEFT COVER 1. Rear cover ( 2. Operation panel ( Operation Panel) 1.
PAGE 46
CÓPIA NÃO CONTROLADA Exterior Covers 3.3.5 FRONT COVER UNIT 1. Rear cover ( Rear Cover) 2. Operation panel ( 3. Transfer unit ( Transfer Unit) 4. Right cover ( 5. Cover link gear unit [A] ( x 2) 6. Release the belt [B] 7.
PAGE 47
CÓPIA NÃO CONTROLADA Laser Optics Rev. 08/24/2009 3.4 LASER OPTICS ⇒ Before performing this procedure, please refer to Technical Service Bulletin – G165/G166/G167/G181/G183/G184 – 026 Laser Optics Housing Replacement. Turn off the main power switch and unplug the printer before beginning any of the procedures in this section. Laser beams can cause serious eye injury. 3.4.1 CAUTION DECAL LOCATIONS Caution decals are attached as shown below.
PAGE 48
CÓPIA NÃO CONTROLADA Laser Optics 3.4.2 LASER OPTICS HOUSING UNIT 1. Rear cover ( Rear Cover) 2. Controller box cover ( 3. MF model only: Remove the controller bracket ( 4. Disconnect the three harnesses from CN301, 302 and 303 on the EGB ( 5. Open the top cover [A]. Controller Board) G165/G166/G167/G181/G183/G184 EGB) 3-8 CÓPIA NÃO CONTROLADA x 3).
PAGE 49
CÓPIA NÃO CONTROLADA Laser Optics 6. Lift up the hook [B] of the harness guide at the rear-left frame and slide the harness Replacement Adjustment guide to the right. 7. Stoppers [C] ( x 2 each; left side and right side) 8. Remove the springs [D] (left side and right side). 9. Remove the laser optics housing unit [E] from the top cover and place it on the main body. Always use two hands when carrying the laser optics housing unit. Be sure not to drop the laser optics housing unit.
PAGE 50
CÓPIA NÃO CONTROLADA Laser Optics 10. Take out the harnesses [F] (= x 1). 11. Remove the laser optics housing unit.
PAGE 51
CÓPIA NÃO CONTROLADA Laser Optics Rev. 08/24/2009 Before performing this procedure, please refer to Technical Service Bulletin – G165/G166/G167/G181/G183/G184 – 026 Laser Optics Housing Replacement. Do the following step 2 with the front cover of the machine open. 1. Open the front cover and turn on the machine. 2. Input the setting values for the laser optics housing unit.
PAGE 52
CÓPIA NÃO CONTROLADA AIO Cartridge 3.5 AIO CARTRIDGE 3.5.1 AIO CARTRIDGE (ALL IN ONE CARTRIDGE) 1. Open the top cover. 2. AIO cartridge [A] 3.5.2 BLACK AIO MOTOR 1. Left cover ( Left Cover) 2. Disconnect the fusing connector [A] and remove the fusing relay harness [B] (hooks).
PAGE 53
CÓPIA NÃO CONTROLADA Replacement Adjustment AIO Cartridge 3. Fusing harness guide [C] ( x 2) 4. Disconnect the connectors shown by arrows in the above picture and release all harnesses on the harness guide [D]. 5.
PAGE 54
CÓPIA NÃO CONTROLADA AIO Cartridge 6. Drive unit [E] ( x 4) 7. Drive unit guide [F] ( x 3) 8.
PAGE 55
CÓPIA NÃO CONTROLADA 9.
PAGE 56
CÓPIA NÃO CONTROLADA AIO Cartridge 3.5.3 COLOR AIO MOTOR 1. Drive unit ( Black AIO Motor) 2. Drive unit guide [A] ( x 3) 3. Color AIO gears [B] (ring stopper x 1 each) 4.
PAGE 57
CÓPIA NÃO CONTROLADA Image Transfer Rev. 08/2008 3.6 IMAGE TRANSFER ⇒3.6.1 IMAGE TRANSFER BELT UNIT To simplify the procedure, remove the lower fusing entrance guide instead of the fusing unit during image transfer belt removal. 1. Remove all the AIO cartridges ( 2. Transfer unit ( AIO Cartridge). Replacement Adjustment Transfer Unit) Lower Fusing Entrance Guide Hook 3. Remove the lower fusing entrance guide (1 hook). 4. Remove the waste toner bottle. 5. Remove the two screws [A].
PAGE 58
CÓPIA NÃO CONTROLADA Image Transfer 6. Rev. 08/2008 Pull out the image transfer belt unit [B]. After replacing the image transfer belt unit Do the following step 2 with the front cover of the machine open. 1. Open the front cover and turn on the machine. 2. Execute "Reset Transfer Unit Life Counter" with the "SP Mode 2" tab (printer model) or the "Engine Maintenance" menu (MF model). 3. Close the front cover. 4. Execute "Trans.
PAGE 59
CÓPIA NÃO CONTROLADA Image Transfer 3.6.2 ITB (IMAGE TRANSFER BELT) CLEANING UNIT The ITB cleaning unit contains waste toner. When removing the ITB cleaning unit, put it on a sheet of paper. Image transfer belt unit ( Image Transfer Belt Unit) 2. Left handle [A] (hook, bushing x 1) 3. Right handle [B] (hook, bushing x 1) 4. ITB cleaning unit [C] ( x 2) Replacement Adjustment 1.
PAGE 60
CÓPIA NÃO CONTROLADA Image Transfer 3.6.3 AGITATOR MOTOR 1. Right cover ( Right Cover) 2. Motor bracket [A] ( x 2) 3. Agitator motor assembly [B] ( x 1, 4.
PAGE 61
CÓPIA NÃO CONTROLADA Image Transfer 3.6.4 ITB (IMAGE TRANSFER BELT) CONTACT MOTOR Agitator motor ( Agitator Motor) 2. Release the wire [A]. 3. ITB contact motor assembly [B] ( x 1, 4. ITB contact motor [C] ( x 2) Replacement Adjustment 1.
PAGE 62
CÓPIA NÃO CONTROLADA Image Transfer 3.6.5 ITB (IMAGE TRANSFER BELT) CONTACT SENSOR 1. Right cover ( Right Cover) 2. High voltage power supply board ( 3. ITB contact sensor assembly [A] ( x 1, 4.
PAGE 63
CÓPIA NÃO CONTROLADA Image Transfer 3.6.6 TM (TONER MARK) SENSOR BASE 1. Open the top cover. 2. Remove all AIO cartridges ( 3. Slide the ITB unit to the front side or remove it. 4. Rear cover ( 5. Controller box cover ( 6. MF models only: Controller bracket ( 7. Disconnect CN306 on the EGB (= x 1). 8. Harness cover [A] (hook) 9. TM sensor base [B] AIO Cartridge).
PAGE 64
CÓPIA NÃO CONTROLADA Image Transfer 3.6.7 WASTE TONER BOTTLE SET SENSOR 1. Remove all AIO cartridges. ( AIO Cartridge) 2. Image transfer belt unit ( Image Transfer Belt Unit) 3. EGB ( 4. Remove two screws [A] for the waste toner sensor base. 5.
PAGE 65
CÓPIA NÃO CONTROLADA 6. Waste toner bottle set sensor [C] (hooks, x 1) When reinstalling the waste toner bottle set sensor, connect it to the white connector of the harness.
PAGE 66
CÓPIA NÃO CONTROLADA Image Transfer 3.6.8 WASTE TONER OVERFLOW SENSOR 1. Remove all AIOs. ( 2. Image transfer belt unit ( Image Transfer Belt Unit) 3. EGB ( 4. Waste toner sensor base ( 5. Waste toner overflow sensor [A] (hooks, AIO Cartridge) EGB) Waste Toner Bottle Set Sensor) x 1) When reinstalling the waste toner overflow sensor, connect it to the black connector of the harness.
PAGE 67
CÓPIA NÃO CONTROLADA Paper Transfer 3.7 PAPER TRANSFER 3.7.1 TRANSFER UNIT Open the front cover. 2. Release the locks [A]. 3. Transfer unit [B] Replacement Adjustment 1.
PAGE 68
CÓPIA NÃO CONTROLADA Paper Transfer 3.7.2 TRANSFER ROLLER 1. Transfer Unit ( Transfer Unit) 2. Release the two hooks [A] at both sides of the transfer unit. 3. Open the transfer roller unit [B] and remove it. 4.
PAGE 69
CÓPIA NÃO CONTROLADA 5. Release the holder [D] at the left side of the transfer roller unit (hook). 6.
PAGE 70
CÓPIA NÃO CONTROLADA Paper Transfer 3.7.3 REGISTRATION ROLLER 1. Transfer unit ( Transfer Unit) 2. Transfer roller unit ( 3. Tension springs [A] (both sides) 4. Registration idle roller [B] ( x 2, gear x 1, bushing x 2) 5. Registration roller [C] ( x 2, gear x 2, bushing x 2) Transfer Roller) Reassembling the registration roller unit When installing the tension spring, make sure that the tension spring correctly hooks onto the bushing of the registration idle roller as shown above [A].
PAGE 71
CÓPIA NÃO CONTROLADA Paper Transfer 3.7.4 REGISTRATION SENSOR Right Cover ( 2. Registration sensor assembly [A] ( x 1, 3. Registration sensor [B] (hooks) SM Right Cover) 3-31 Replacement Adjustment 1.
PAGE 72
CÓPIA NÃO CONTROLADA Paper Transfer 3.7.5 REGISTRATION CLUTCH 1. Rear cover ( Rear Cover) 2. Left cover ( 3. Transport/Fusing motor ( 4.
PAGE 73
CÓPIA NÃO CONTROLADA Image Fusing 3.8 IMAGE FUSING Make sure that the fusing unit is cool before you touch it. The fusing unit can be very hot. Make sure to restore the insulators, shields, etc after you service the fusing unit. 3.8.1 FUSING UNIT Open the front cover. 2. Rear cover ( Rear Cover) 3. Right cover ( Right Cover) 4. Left cover ( 5. Disconnect the connectors [A] (hook) [B]. Replacement Adjustment 1. Left Cover) The sponge [C] clamps the harness.
PAGE 74
CÓPIA NÃO CONTROLADA Image Fusing 3.8.2 FUSING LAMP 1. Fusing unit ( Fusing Unit) 2. Fusing front cover [A] ( x 4) 3. Fusing lamp [B] ( x 2, ground cable x 1) When Reinstalling the Fusing Lamp The terminal [A], which shows the voltage and power ratings, must be placed at the left side of the fusing unit (fusing cable side).
PAGE 75
CÓPIA NÃO CONTROLADA Image Fusing 3.8.3 TRANSPORT/FUSING MOTOR 1. Rear cover ( Rear Cover) 2. Left cover ( 3. Disconnect the fusing connector [A] (hook). 4. Fusing harness guide [B] ( x 2) 5. For only the duplex model: Duplex timing belt [C] 6. Transport/Fusing motor assembly [D] ( x 3, 7.
PAGE 76
CÓPIA NÃO CONTROLADA Paper Feed 3.9 PAPER FEED 3.9.1 PAPER FEED CLUTCH 1. Rear cover ( Rear Cover) 2. Left cover ( 3. Disconnect the fusing relay harness [A] (hook). 4.
PAGE 77
CÓPIA NÃO CONTROLADA Paper Feed 3.9.2 PAPER FEED ROLLER 1. Remove all the AIO cartridges. 2. Remove the waste toner bottle. 3. Rear cover ( 4. Left cover ( 5. Paper feed clutch ( 6. Close the top cover and front cover. 7. Pull out the tray. 8. Stand the machine with the rear side Rear Cover) Left Cover) Replacement Adjustment Paper Feed Clutch) facing the table. 9. Slide the paper feed shaft [A] to the left side ( x 2). 10.
PAGE 78
CÓPIA NÃO CONTROLADA Paper Feed 3.9.3 SEPARATION PAD 1. Pull out the tray. 2. Push down the bottom plate [A]. 3. Separation pad [B] (hooks, spring x 1) When reinstalling the separation pad, make sure that the mylar [C] is not placed under the separation pad. The right side image above shows incorrect installation.
PAGE 79
CÓPIA NÃO CONTROLADA Paper Feed 3.9.4 PAPER END SENSOR Rear cover ( Rear Cover) 2. Right cover ( Right Cover) 3. High voltage power supply board ( High Voltage Power Supply Board) 4. Paper end sensor assembly [A] ( x 1) 5. Paper end sensor [B] (hooks) Replacement Adjustment 1.
PAGE 80
CÓPIA NÃO CONTROLADA Paper Exit 3.10 PAPER EXIT 3.10.1 PAPER EXIT ROLLER 1. Operation panel ( Operation Panel) 2. Remove the bushing [A] ( x 1) 3. Paper exit roller [B] ( x 1) 4. Remove the four exit guides [C] and gear [D] (bushing x 1).
PAGE 81
CÓPIA NÃO CONTROLADA Paper Exit Replacement Adjustment When reinstalling the paper exit roller Make sure that the ground wire [A] from the discharge sheet touches the ground plate [B] on the machine after reinstalling the paper exit roller.
PAGE 82
CÓPIA NÃO CONTROLADA Paper Exit 3.10.2 PAPER EXIT SENSOR 1. Rear cover ( Rear Cover) 2. Right cover ( Right Cover) 3. Right bracket [A] ( x 4) 4.
PAGE 83
CÓPIA NÃO CONTROLADA Electrical Components 3.11 ELECTRICAL COMPONENTS 3.11.1 CONTROLLER BOARD GDI/ PCL Controller Board (Printer Model) Rear cover ( Rear Cover) 2. Controller box cover [A] ( x 7) 3. Interface bracket [B] ( x 2) 4. GDI controller board [B] or PCL controller board [C] ( x 6) Replacement Adjustment 1.
PAGE 84
CÓPIA NÃO CONTROLADA Electrical Components Main Controller Board (MF Model) 1. Rear cover ( 2. Controller box cover [A] ( x 7) 3. Interface bracket [B] ( x 2) 4. Main controller board [C] (flat cable x 1, all Rear Cover) s, x 6) The photo above left shows the G184, and the photo above right shows the G181 and G183.
PAGE 85
CÓPIA NÃO CONTROLADA Electrical Components PDL Board (G184 only) Rear cover ( Rear Cover) 2. Controller box cover (see "Main Controller Board" above) 3. Interface bracket (see "Main Controller Board" above) 4. PDL board [A] ( x 4) Replacement Adjustment 1.
PAGE 86
CÓPIA NÃO CONTROLADA Electrical Components 3.11.2 EGB (ENGINE BOARD) Printer Model 1. Rear cover ( Rear Cover) 2. GDI controller or PCL controller board ( 3. EGB [A] ( x 6, all 4. EEPROM [B] Controller Board) s) When installing the new EGB 1. Remove the EEPROM from the old EGB.
PAGE 87
CÓPIA NÃO CONTROLADA 2. Install it on the new EGB with the mark [A] pointing to the left side of the board after you replace the EGB. 3. Replace the EEPROM if the EEPROM on the old EGB is defective. Keep the EEPROM away from objects that can cause static electricity. Static electricity can damage EEPROM data. SM Make sure that the EEPROM is correctly installed on the EGB.
PAGE 88
CÓPIA NÃO CONTROLADA Electrical Components MF Model 1. Rear cover ( Rear Cover) 2. Controller box cover ( 3.
PAGE 89
CÓPIA NÃO CONTROLADA Electrical Components EGB [B] ( x 6, all 5. EEPROM [C] s) Replacement Adjustment 4. When installing the new EGB 1. Remove the EEPROM from the old EGB. 2. Install it on the new EGB with the mark [A] pointing to the left side of the board after you replace the EGB. 3. Replace the EEPROM if the EEPROM on the old EGB is defective. Keep the EEPROM away from any objects that can cause static electricity. Static electricity can damage EEPROM data.
PAGE 90
CÓPIA NÃO CONTROLADA Electrical Components 3.11.3 FCU (G183/G184 ONLY) 1. Rear cover ( Rear Cover) 2. Controller box cover ( 3. Controller bracket ( 4.
PAGE 91
CÓPIA NÃO CONTROLADA Electrical Components 3.11.4 INTERLOCK SWITCHES 1. Operation panel ( Operation Panel) 2. Rear cover ( 3. Left cover ( 4. Interlock switch base [A] ( x 4, all Rear Cover) Replacement Adjustment Left Cover) 5. s) Removing the spring [B] first makes this procedure easier. Remove all the connectors after the interlock switch base has been removed.
PAGE 92
CÓPIA NÃO CONTROLADA Electrical Components 3.11.5 FUSING FAN MOTOR 1. Operation panel ( 2. Rear cover ( 3. Left cover ( 4. Interlock switch base ( 5. Fusing fan base [A] ( x 2, 6. Fusing fan motor [B] (hooks, Operation Panel) Rear Cover) Left Cover) Interlock Switches) x 1) x 1) Install the fusing fan motor with its decal facing the outside of the machine.
PAGE 93
CÓPIA NÃO CONTROLADA Electrical Components 3.11.6 LSU FAN MOTOR 1. Operation panel ( Operation Panel) 2. Rear cover ( 3. Left cover ( 4. LSU fan motor [A] (hooks, Rear Cover) Replacement Adjustment Left Cover) SM x 1) Install the LSU fan motor with its decal facing the outside of the machine.
PAGE 94
CÓPIA NÃO CONTROLADA Electrical Components 3.11.7 ID CHIP BOARD 1. Operation panel ( 2. Rear cover ( 3. Left cover ( 4. Controller box cover (printer model: model: Operation Panel) Rear Cover) Left Cover) Controller Board) or controller bracket (MF Controller Board) 5. Disconnect the connector (CN305) on the EGB. 6. Interlock switch base ( 7. Fusing fan base ( 8. Drive unit ( 9. Move the harnesses away from the LSU fan base [A].
PAGE 95
CÓPIA NÃO CONTROLADA Electrical Components 3.11.8 PSU 1. Operation panel ( Operation Panel) 2. Rear cover ( 3. Left cover ( Left Cover) 4. Drive unit ( Black AIO Motor) 5. LSU fan base ( 6. PSU guide [A] ( x 3) 7. Power cord bracket [B] ( x 2) 8. Ground cable [C] ( x 1) 9.
PAGE 96
CÓPIA NÃO CONTROLADA Electrical Components 10. PSU assembly [E] ( x 4, all s) 11. PSU [F] ( x 4) Fuse There is a removable fuse on the PSU. Fuse No. Rating FU101: NA 15 A, 125V FU101: EU, ASIA 6.3A, 250V Use a correct rating fuse for the fuse replacement. Never use a wrong rating fuse. If you do, the machine may be damaged. Never try direct connection of PSU circuit without a fuse.
PAGE 97
CÓPIA NÃO CONTROLADA Electrical Components 3.11.9 HIGH VOLTAGE POWER SUPPLY BOARD 1. Remove all AIO cartridges. 1. Operation panel ( 2. Rear cover ( Rear Cover) 3. Right cover ( Right Cover) 4. High Voltage Power Supply Board [A] ( x 7, ground cable x 1, Replacement Adjustment Operation Panel) x 1) 3.11.10 TEMPERATURE/HUMIDITY SENSOR 1. Operation panel ( 2. Rear cover ( Rear Cover) 3. Right cover ( Right Cover) 4.
PAGE 98
CÓPIA NÃO CONTROLADA Electrical Components 3.11.11 DUPLEX MOTOR (DUPLEX MODEL) 1. Operation panel ( Operation Panel) 2. Rear cover ( 3. Left cover ( 4. Disconnect the fusing connector [A] 5. Duplex timing belt [B] 6. Left bracket [C] ( x 4) 7.
PAGE 99
CÓPIA NÃO CONTROLADA Electrical Components 3.11.12 SPEAKER (G183/G184 ONLY) Rear cover ( Rear Cover) 2. Controller box cover ( 3. Speaker [A] ( x 2, Controller Board) Replacement Adjustment 1.
PAGE 100
CÓPIA NÃO CONTROLADA Electrical Components 3.11.13 EEPROM Replacement and Reinstallation procedures for the EEPROM are included in the "EGB (Engine Board)" replacement procedure. Refer to "EGB (Engine Board)" for details. When replacing an old EEPROM with a new EEPROM, EEPROM setting is required. Follow the EEPROM setting procedure described below. Printer Model Do the following steps 1 to 11 with the front cover of the machine open. After completing these steps, turn off the machine. 1.
PAGE 101
CÓPIA NÃO CONTROLADA 8. Select a plug and play name from the "PnP Name" box. 9. Click the "SP Mode 2" tab. 10. Input the LSU (laser optics housing unit) setting values in the "LSU Adjustment" box. 11. Turn off the machine. 12. Turn on the machine with the front cover open. 13. Enter SP Mode 2. 14. Close the front cover. 15. Click "Trans. Belt Adjust" to adjust the ITB (Image Transfer Belt) unit. 16. Select "ON" or "OFF" for the consecutive fusing jam detection with the "Fuser SC Detect" box.
PAGE 102
CÓPIA NÃO CONTROLADA Electrical Components MF Model Do the following steps 1 to 9 with the front cover of the machine open. After completing these steps, turn off the machine. 1. Open the front cover and turn on the machine. The machine may issue an error code (because the cover is open), but continue this procedure. 2. Enter the following keys consecutively in order to enter "Engine Maintenance" in the "Maintenance Mode Menu.
PAGE 103
CÓPIA NÃO CONTROLADA Electrical Components 17. Select "Registration", and then adjust the registration for each direction (vertical and horizontal direction) and tray if necessary. 18. Select "2nd Transfer Fuser Temp" and then adjust the transfer roller bias and the temperature reduction of the fusing unit for each paper type and for the front and back sides. The default settings for normal operation are all '0'. Replacement Adjustment 19. Exit "Engine Maintenance.
PAGE 104
CÓPIA NÃO CONTROLADA ADF 3.12 ADF 3.12.1 ADF UNIT 1. Stand left cover [A] 2. Disconnect the ADF harness [B] and power cord [C]. 3.
PAGE 105
CÓPIA NÃO CONTROLADA 4. Release the three hooks of the right hinge [E] 5. Lift the ADF unit. Replacement Adjustment ADF 3.12.2 ORIGINAL TRAY 1. Open the ADF cover. 2. Release the front tab [A]. 3.
PAGE 106
CÓPIA NÃO CONTROLADA ADF 3.12.3 ADF FEED UNIT 1. Open the ADF cover. 2. Release the lock lever [A] 3. ADF feed unit [B] 3.12.4 ADF SEPARATION PAD 1. Open the ADF cover. 2. ADF feed unit ( 3.
PAGE 107
CÓPIA NÃO CONTROLADA ADF 3.12.5 ADF FRONT COVER 1. ADF unit ( ADF Unit) 2. Original Tray ( 3. ADF feed unit ( 4. ADF front cover [A] ( x 1) Original Tray) Replacement Adjustment ADF Feed Unit) 3.12.6 ADF REAR COVER 1. ADF unit ( 2. Original Tray ( 3. ADF feed unit ( 4.
PAGE 108
CÓPIA NÃO CONTROLADA ADF 3.12.7 ADF COVER 1. ADF unit ( ADF Unit) 2. ADF front cover ( ADF Front Cover) 3. ADF rear cover ( ADF Rear Cover) 4.
PAGE 109
CÓPIA NÃO CONTROLADA ADF 3.12.8 ADF MOTOR 1. ADF unit ( ADF Unit) 2. Original Tray ( 3. ADF feed unit ( 4. ADF front cover ( ADF Front Cover) 5. ADF rear cover ( ADF Rear Cover) 6. ADF drive unit [A] ( x 4, all 7. ADF motor assembly [B] ( x 2) 8.
PAGE 110
CÓPIA NÃO CONTROLADA ADF 3.12.9 ORIGINAL SET SENSOR 1. ADF unit ( ADF Unit) 2. ADF feed unit ( 3. ADF motor assembly ( 4. Feed roller holder [A] ( x 1) 5. Upper guide [B] ( x 2) 6.
PAGE 111
CÓPIA NÃO CONTROLADA ADF 3.12.10 ADF COVER OPEN SENSOR 1. Original tray ( Original Tray) 2. ADF rear cover ( 3.
PAGE 112
CÓPIA NÃO CONTROLADA ADF 3.12.11 ADF FEED SENSOR 1. ADF unit ( ADF Unit) 2. ADF feed unit ( 3. Sensor cover [A] ( x 2) 4.
PAGE 113
CÓPIA NÃO CONTROLADA ADF 3.12.12 ADF DRIVE BOARD 1. Original tray ( Original Tray) 2. ADF rear cover ( 3.
PAGE 114
CÓPIA NÃO CONTROLADA Scanner 3.13 SCANNER 3.13.1 SCANNER UNIT 1. Controller box cover ( Controller Box Cover) 2. Disconnect the flat cable [A]. 3. Stand left cover [B] and right cover [C] (1 hook each) 4. Disconnect the scanner harness, power cord and ground cable (and the ADF harness and power cord if the ADF is installed in the scanner unit) ( x 1). 5. Open the top cover of the machine.
PAGE 115
CÓPIA NÃO CONTROLADA Replacement Adjustment Scanner 6. Remove the stepped screw [D]. 7. Push the lock button [E] and slide the scanner unit to the rear. 8. ADF unit ( 9.
PAGE 116
CÓPIA NÃO CONTROLADA Scanner 3.13.2 SCANNER TOP COVER 1. Scanner unit ( Scanner Unit) 2. Turn over the scanner unit. 3. Scanner front cover [A] (tabs x 3) 4. Remove the six screws at the bottom of the scanner base [B]. 5.
PAGE 117
CÓPIA NÃO CONTROLADA Scanner 3.13.3 SCANNER CARRIAGE UNIT Scanner unit 2. Scanner top cover 3. Slide the scanner carriage unit [A] to the right side. 4. Remove the timing belt tension spring [B] 5. Remove the flat cable [C] from the scanner carriage unit. SM 3-77 Replacement Adjustment 1.
PAGE 118
CÓPIA NÃO CONTROLADA Scanner 6. Bar holder [D] ( x 1) 7.
PAGE 119
CÓPIA NÃO CONTROLADA Scanner 3.13.4 EXPOSURE LAMP Scanner carriage unit ( Scanner Carriage Unit) 2. Carriage top cover [A] ( x 2, 3. Exposure lamp [B] (hooks) Replacement Adjustment 1.
PAGE 120
CÓPIA NÃO CONTROLADA Scanner When reinstalling the exposure lamp Wire the lamp cords as shown above. Otherwise, the top cover pinches the lamp cords and damages them when reinstalling the top cover on the scanner carriage unit.
PAGE 121
CÓPIA NÃO CONTROLADA Scanner 3.13.5 LAMP STABILIZER BOARD Scanner carriage unit ( Scanner Carriage Unit) 2. Carriage bottom cover [A] ( x 2) 3. Lamp stabilizer [B] ( Replacement Adjustment 1.
PAGE 122
CÓPIA NÃO CONTROLADA Scanner 3.13.6 SCANNER MOTOR 1. Scanner carriage unit ( Scanner Carriage Unit) 2. Scanner motor [A] ( x 3) 3. Carriage rail [B] ( x 2) 4. Ground plate [C] (double-sided tape) 5.
PAGE 123
CÓPIA NÃO CONTROLADA TROUBLESHOOTING TROUBLESHOOTING REVISION HISTORY Page Date 19 ~ 21 07/29/2008 Added/Updated/New New Information – Supp Info on Color Registration CÓPIA NÃO CONTROLADA
PAGE 124
CÓPIA NÃO CONTROLADA Scanner CÓPIA NÃO CONTROLADA
PAGE 125
CÓPIA NÃO CONTROLADA Error Codes 4. TROUBLESHOOTING 4.1 ERROR CODES 4.1.1 OVERVIEW The error codes will be displayed in the GUI of SOM (Printer model) or on the LCD (MF model) if the machine has a problem. These can be recovered by a customer. 4.1.2 ERROR CODES LIST Cover Open The front or top cover is open. 1. Close the front or top cover. 2. Replace the interlock switches or actuator mechanism.
PAGE 126
CÓPIA NÃO CONTROLADA Error Codes Waste Toner Bottle Set Error 014 Waste toner bottle not set Disconnected or defective harness of the waste toner bottle set sensor Defective waste toner bottle set sensor 1. Install the waste toner bottle. 2. Check or replace the harness of the waste toner bottle set sensor. 3. Replace the waste toner bottle set sensor.
PAGE 127
CÓPIA NÃO CONTROLADA Error Codes Jam Error: No Feed from Optional Tray 052 Paper slipped Remove the paper jam at the optional tray (Tray 2). Inner Jam Error: Registration/ Paper Exit A sheet of paper stays at the registration sensor or paper exit sensor. 055 Paper slipped Paper double feed Paper Exit Jam Error: Paper Exit/ Fusing Unit A sheet of paper stays at the paper exit sensor or winds around the rollers in the 056 fusing unit.
PAGE 128
CÓPIA NÃO CONTROLADA Error Codes 082 Toner Near End: Magenta AIO 083 Toner End: Magenta AIO Magenta toner near-end or end Replace the magenta AIO. 084 Toner Near End: Cyan AIO 085 Toner End: Cyan AIO Cyan toner near-end or end Replace the Cyan AIO. 086 Toner Near End: Yellow AIO 087 Toner End: Yellow AIO Yellow toner near-end or end Replace the yellow AIO.
PAGE 129
CÓPIA NÃO CONTROLADA Service Call Conditions 4.2 SERVICE CALL CONDITIONS 4.2.1 SUMMARY This machine issues an SC (Service Call) code if an error occurs on the machine. The error code can be seen with the SOM ( "Smart Organizing Monitor") (printer models) or on the operation panel (MF models). Make sure that you understand the following points; 1. All SCs are logged. 2. At first, always turn the main switch off and on if an SC code is issued. 3.
PAGE 130
CÓPIA NÃO CONTROLADA Service Call Conditions 4.2.2 ENGINE SC SC 1xx (Other Error) Serial Number Error The serial number stored in the memory (EGB) is not correct. 195 EEPROM defective EGB replaced without original EEPROM 1. Check the serial number. 2. If the stored serial number is incorrect, contact your supervisor. SC 2xx (Laser Optics Error) Polygon motor error 1: ON timeout 202 The polygon mirror motor does not reach the targeted operating speed within 5 sec.
PAGE 131
CÓPIA NÃO CONTROLADA Service Call Conditions Laser Synchronizing Detection Error: [K]/[Y] 220 The laser synchronizing detection signal for LDB [K]/[Y] is not output after the LDB unit has turned on while the polygon motor is rotating normally. Laser Synchronizing Detection Error: [M]/[C] The laser synchronizing detection signal for LDB [M]/[C] is not output after the LDB unit has turned on while the polygon motor is rotating normally.
PAGE 132
CÓPIA NÃO CONTROLADA Service Call Conditions SC 3xx (Charge Error) High voltage power output error The measured voltage is not correct when the EGB measures each charge output (charge, development, image transfer belt unit, and transfer unit). 300 Disconnected or defective high voltage harness Defective high voltage power supply Defective EGB 1. Check or replace the harnesses. 2. Replace the high voltage power supply board 3. Replace the EGB.
PAGE 133
CÓPIA NÃO CONTROLADA Service Call Conditions SC 4xx (Image Transfer and Transfer Error) Process Control Error This SC is issued if the process control adjustment fails 5 times consecutively after AIO replacement. 400 Defective contact at the terminal between the machine and AIO. Dirty TM sensor 1. Check the contact of the terminal and re-install the AIO. 2. Clean the TM sensor.
PAGE 134
CÓPIA NÃO CONTROLADA Service Call Conditions Agitator Motor Error The agitator motor error is detected twice for 10 msec during the initialization at power-on or after the cover is closed. 480 Disconnected or defective harness Defective agitator motor 1. Check or replace the harness. 2. Replace the agitator motor. ITB (Image Transfer Belt) Unit Set Error The TM sensor does not detect the reflection from the ITB. 490 No ITB unit in the machine Dirty TM sensor 1.
PAGE 135
CÓPIA NÃO CONTROLADA Service Call Conditions SC 5xx (Motor and Fusing Error) Main Motor Error The LOCK signal error is detected when the EGB monitors the main motor state. (This monitoring is done immediately after power-on, when the motor starts 500 rotating, and immediately after the motor stops.) Disconnected or defective motor harness. Motor slips due to excessive load 1. Check the harness from the main motor. Replace it if necessary.
PAGE 136
CÓPIA NÃO CONTROLADA Service Call Conditions Thermistor Error The thermistor output is less than 0°C for 7 seconds. Disconnected thermistor Defective harness connection 541 1. Check the harness connection of the thermistor. 2. Replace the fusing unit. Execute "Fuser SC Reset" with SOM (printer models) or "Engine Maintenance Menu" (MF model) to recover the machine after completing the recovery procedure. Otherwise, the machine continues to issue this SC code and cannot be operated.
PAGE 137
CÓPIA NÃO CONTROLADA Service Call Conditions High Temperature Detection Error This SC is issued if one of following conditions occurs: The thermistor (center) detects 255°C or thermistor (end) detects 245°C. The thermistor (center) detects a 3°C increment or more for five seconds at 220°C or more or the thermistor (end) detects a 4°C increment or more for five seconds at 210°C or more. 543 Defective I/O control (EGB) Defective EGB 1.
PAGE 138
CÓPIA NÃO CONTROLADA Service Call Conditions Zero Cross Error The zero cross signal is not detected for three seconds even though the fusing lamp relay is on after turning on the main power or closing the front door. 547 Defective fusing lamp relay 1. Turn the main power switch off and on. Execute "Fuser SC Reset" with SOM (printer models) or "Engine Maintenance Menu" (MF model) to recover the machine after completing the recovery procedure.
PAGE 139
CÓPIA NÃO CONTROLADA Service Call Conditions Zero Cross Frequency Error The detection error occurs ten times consecutively in ten zero cross signal detections. This error is defined when the detected zero cross signal is 17 or less/27 or more for 0.2 seconds. 557 Defective fusing lamp relay Unstable input power source 1. Check the power supply source. 2. Replace the fusing unit.
PAGE 140
CÓPIA NÃO CONTROLADA Service Call Conditions SC 6xx (Communication and Other Error) EEPROM Error An unexpected value exists in the initialization flag of the EEPROM 669 EEPROM not initialized Defective EEPROM 1. Initialize the EEPROM. 2. Replace the EEPROM. 3. Replace the EGB. GAVD Communication Error The ID of the GAVD is not identified during initialization. 690 The chip ID of the GAVD cannot be detected by the machine at power-on. Defective EGB 1. Replace the EGB.
PAGE 141
CÓPIA NÃO CONTROLADA Service Call Conditions 4.2.3 CONTROLLER SC SC8xx Service Cycle Power 819 Incorrect combination of EGB and controller board. An unexpected error occurs in the EEPROM on the controller board. Controller board defective 1. Install the correct EGB and controller boards for this machine. 2. Replace the controller board 823 An interface error in the USB connection or NIB connection occurs. Controller board defective 1. Replace the controller board.
PAGE 142
CÓPIA NÃO CONTROLADA Service Call Conditions ROM Checksum Error 828 A ROM checksum error at power-on occurs. 1. Replace the controller board.
PAGE 143
CÓPIA NÃO CONTROLADA Image Problems Rev. 07/2008 4.3 IMAGE PROBLEMS 4.3.1 OVERVIEW Image problems may appear at regular intervals that depend on the circumference of certain components.
PAGE 144
CÓPIA NÃO CONTROLADA ⇒ Image Problems Rev. 07/2008 Color Registration Procedure: 1. First, request customers to use the color registration in User Tools. - G165, G166, G167: See the “Maintenance” tab inside the Smart Organization Monitor (SOM) menu. - G181, G183, G184: If the control unit version is v1.30 or newer, see “Machine Settings” inside the User Menu. If the control unit version is earlier then v1.30, turn the main power OFF/ON.
PAGE 145
CÓPIA NÃO CONTROLADA Image Problems Rev.
PAGE 146
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 147
CÓPIA NÃO CONTROLADA SERVICE TABLES SERVICE TABLES REVISION HISTORY Page Date 47 ~ 49 07/05/2009 Added/Updated/New Updated Information – Service Menu (MF Model) CÓPIA NÃO CONTROLADA
PAGE 148
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 149
CÓPIA NÃO CONTROLADA Service Program 5. SERVICE TABLES 5.1 SERVICE PROGRAM 5.1.1 OVERVIEW The Model PE series contains printer models and MF models. Each model type (printer model and MF model) has a different service program menu. Here is a summary. Printer Model There is no LCD on the printer models. To execute the service program, execute the SOM (Smart Organizing Monitor), which is provided with the printer driver, from your computer.
PAGE 150
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) SMART ORGANIZING MONITOR (PRINTER MODEL) 5.2 5.2.1 OVERVIEW SOM (Smart Organizing Monitor) is a utility which can check the status of a printer and set up a printer from a PC. This utility is executed from a printer driver. 5.2.2 PRINTER DRIVER INSTALLATION (USB CONNECTION) 1. Close all applications currently running. 2. Check the following: 3.
PAGE 151
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) 5.2.3 ENTERING THE PRINTER CONFIGURATION To enter the service system setting; Start the SOM utility. 2. Click the "User Tools" tab. 3. Click "Printer Configuration.” 4. The "Access Code" entry dialog appears. 5. Input "Admin074.” 6. Click the "OK" button. SM Service Tables 1.
PAGE 152
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) 7. The "Printer Configuration" GUI appears.
PAGE 153
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) 5.2.4 PRINTER CONFIGURATION MENU LIST The SOM has the following printer configuration menus. Each menu contains various setting items. The details of each setting item are explained in this section below. Menu Description Paper Input Adjusts the paper type and size settings. Adjusts the image registration and executes the color registration adjustment. System Adjusts the system settings of the machine.
PAGE 154
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Paper Input Item Selections Remarks A4 */ B5/ A5/ B6/ A6/ Legal/ Letter*/ Tray 1 Paper Size (standard) Half Letter/ Executive/ 8" x 13"/ 8.
PAGE 155
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Item Tray 2 Paper type (optional) Selections Remarks Thin Paper(60-75g/m2)/ Plain*/ Plain Paper(90-105g/m2)/ Recycled/ Color/ Preprinted Paper/ - Prepunched Paper/ Letterhead If the paper size factory default is A4, then the custom size factory Custom Size unit default unit is mm. Mm */ Inch * If the paper size factory default is Letter, then the custom size factory 3.54 – 8.50 inch.
PAGE 156
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Item Selections Remarks MPT Priority Tray Not used Tray1 * - Tray2 "*" indicates the factory default value.
PAGE 157
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Group (Tab) Item Selections Remarks Sends a PCL or GDI command to the Print Test printer to print a test sheet. Sheet button It is disabled when tray 2 is not installed. 0.34 mm per step. Range is -5 mm to +5 Registration Adjustment (-15 to +15) Horizontal step mm. If the machine settings are reset to the factory defaults, this value does not Tray 2 change. 0.24 mm per step. Range is -3.
PAGE 158
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Group (Tab) Item Selections Remarks The engine will do color registration and Color Registration density tuning automatically. Adjust button The printer will warm up automatically after this setting is changed. This button is for updating the controller FW Update FW update firmware. The button for updating the button button engine firmware is located in the "SP Mode 1" tab. "*" indicates the factory default value.
PAGE 159
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Item Selections Auto Continue On/Off * Copies 1*-999 Sub Paper Size Off */ Auto 2 Sided Print Remarks PCL only. Default is 1. Always disabled in the GDI model. PCL. A4 Letter override Off */ Short Edge Bind/ Long Edge Bind PCL only "Manual Duplex/Cover" has higher Blank Page Print Print */ Not Print priority than the "Blank Pages" setting.
PAGE 160
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Item Selections Remarks 5min * Energy Save Time 15min 30min 60min B/W Page Detect On * Off Notify by E-mail On Off * Print Error Page Machine Comment On PCL only Off * PCL only Up to 32 alphanumeric characters. Null string* The factory default is 'null string'. Restores all settings to the factory Restore to Factory default settings for the market area Default button setting.
PAGE 161
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Item Selections Remarks Swedish Norwegian Portuguese Polish Czech Hungarian Finnish Service Tables Japanese Simplified Chinese Traditional Chinese Russian Access Code Used * Not used Changes the access code. The button Access code is grey if the Access code is set to "not change button NetRicoh URL edit box used.” http://www.netricoh.com/* "*" indicates the factory default value.
PAGE 162
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Network 1 Group (Tab) Item Selections Machine Remarks String length is 32 Name Machine String length is 32 Comment Hardware Information Type Mac Address Active Protocol TCP/IP, Netware, Apple List of 3 protocols when they are active.
PAGE 163
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Group (Tab) Item Selections Remarks This setting is not available if DHCP is enabled. If this setting is changed, the printer IP address xxx.xxx.xxx.xxx power must be turned off/on for the new setting to take effect. The default setting is "192.0.0.192" when DHCP is off. This setting is not available if DHCP is enabled. power must be turned off/on for the new Subnet mask setting to take effect. xxx.xxx.xxx.
PAGE 164
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Group (Tab) Item Selections Remarks If this setting is changed, the printer DHCP On */ Off power must be turned off/on for the new setting to take effect. Up to 32 alphanumeric characters. This setting is not available if DHCP is enabled. The default setting is "0.0.0.0"when DNS Server IP Address DHCP is off. xxx.xxx.xxx.xxx The setting when DHCP is changed from on to off is the previous setting when DHCP was on.
PAGE 165
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) (Tab) Item USB I/O Timeout Network I/O Timeout TCP/IP Selections Remarks 15 60 * 300 15 60 * 300 If this setting is changed, the printer Active* power must be turned off/on for the new Not Active setting to take effect. PCL only Netware Active* If this setting is changed, the printer Not Active power must be turned off/on for the new Interface setting to take effect.
PAGE 166
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Network 2 Group (Tab) Item Selections Remarks Auto Select* PCL only. If this setting is changed, the printer Frame Type Ethernet ll power must be turned off/on for the new setting to take effect. Bindery Login Mode PCL only. If this setting is changed, the printer Both power must be turned off/on for the new IPX setting to take effect. NDS* PCL only. Up to 47 alphanumeric characters.
PAGE 167
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Group (Tab) Item Selections Remarks PCL only. Up to 48 alphanumeric characters. NDS Tree Null string* The factory default is 'null string'. If this setting is changed, the printer power must be turned off/on for the new setting to take effect. PCL only. Always disabled in GDI. Up to 127 alphanumeric characters. NDS Context Name Null string* The factory default is 'null string'.
PAGE 168
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Group (Tab) Item Selections Remarks Up to 64 alphanumeric characters. E-mail Address Null string* (address for receiving e-mail) The factory default is 'null string'. Administrator e-mail address Null string* Up to 64 alphanumeric characters. The factory default is 'null string'. SMTP server "*" indicates the factory default value.
PAGE 169
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Group (Tab) Item Community Name Selections Remarks Up to 15 alphanumeric characters. Null string * The factory default is 'null string'. The factory default is 0.0.0.0 SNMP Host IP Address If this setting is changed, the printer power must be turned 0.0.0.0 * off/on for the new setting to take effect.
PAGE 170
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Group (Tab) Item Selections Remarks PCL only. String length is 20. The factory default is 20 "F" characters. Valid characters are: "0123456789ABCDEFabcdef"; not case sensitive when setting but the capital character will change to lower case when reading. Host IPX "FFFFFFFFFFFFFFFFFFFF" Address * If this setting is changed, the printer power must be turned off/on for the new setting to take effect. A valid string length is 0 or 20.
PAGE 171
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Group (Tab) Item Selections Remarks PCL only. Default is "*.” Up to 32 in length. The factory default string is "*.” Zone Name If this setting is changed, the "*" * printer power must be turned off/on for the new setting to take effect. Service Tables "*" indicates the factory default value.
PAGE 172
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Printer (PCL only) Group (Tab) Item Selections Remarks Portrait * Orientation Landscape If the machine settings are reset Form Lines 5 to 128 by 1 to the factory defaults, this value does not change. PCL Font Number Font Size Font Pitch 0*-89 The factory default value is 0. 4 to 999.75 by 0.25 (12 *) 0.44 to 99.99 by 0.01 (10 *) G165/G166/G167/G181/G183/G184 The factory default value is 12. The factory default value is 10.
PAGE 173
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Group (Tab) Item Selections Remarks Roman-8*, Roman-9, ISO L1, ISO L2, ISO L5, PC-8, PC-8 D/N, PC-850, PC-852, PC-858, PC-8 TK, Win L1, Win L2, Win L5, Desktop, PS Text, VN Intl, VN US, MS Publ, Symbol Set Math-8, PS Math, Service Tables VN Math, Pi Font, Legal, ISO 4, ISO 6, ISO 11, ISO 15, ISO 17, ISO 21, ISO 60, ISO 69, Win 3.0, MC Text, ISO L6, ISO L9, PC-775, PC-1004, Courier Font Regular* Dark Ext.
PAGE 174
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Group (Tab) Item Selections Remarks 600x600dpi 1bit* Resolution 600x600dpi 2bits 600x600dpi 4bits 600 x 600 dpi* Resolution 600 x 600 dpi 2bits 600 x 600 dpi 4bits PS Off Color Profile Solid color * Presentation Photographic "*" indicates the factory default value.
PAGE 175
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Item Selections Remarks Text This means "toner limit.” Should by text/graphic/image. Toner Limit Selection Graphic [200 to 400 / 250 (default) / 10/step] Image Print Side Volume Total Total printed page counter Color Total printed color page counter B/W Total printed mono page counter Total printed duplex page counter.
PAGE 176
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Item Selections Remarks Duplex jam counter Paper Jam - Duplex [0 to 128] Always 0 if the printer does not have a duplex unit. Recent K coverage = K data got from the engine (the unit is 1024 dots) / A4 full coverage dot number (the unit is 1024 dots). Recent K, M, C, Y A4 full coverage dot number in units of coverage 1024 dots is 4961*7016/1024. Recent M, C, Y coverage uses the same equation as K, using the M, C, Y data from the engine.
PAGE 177
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Item Selections Remarks This clears all counters except "Full Color" and "Black and White" in the total counter. Init Engine When you click the [Init Engine EEPROM EEPROM] button, the engine EEPROM is initialized. Turn the machine power off/on after you change this setting. Displays and changes a serial number. (Character: alphanumeric, Serial No.
PAGE 178
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Item Selections Remarks Displays and changes a destination. It may damage the printer if you change this setting. Turn the machine power off/on after 1 byte. Destination 0:DOM (JPN), 1:NA, 2:EU, 3:China, 4:Taiwan, 5:AP, 6:LA you change this setting. The printer will warm up automatically after this setting is changed. SOM will show a blank space if the printer destination setting is unknown.
PAGE 179
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Item Selections Remarks Display string only 0: Plain paper 1 mode 1: Plain paper 2 mode 2: Plain paper 3 mode 3: Reserved (not display) Media type 4: Thick stock 1 mode Please select the media type. 5: Thick stock 2 mode 6: Thick stock 3 mode (Not used) 7: Thick stock 4 mode This adjusts the transfer roller current, based on the default value. The range of adjustment is from -15 Front (-15 to +15) [μA] to +15 [μA], in units of 1.
PAGE 180
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Item Model Selections Remarks Display string only Displays the current model in a 1: PE-P1a dropdown list. 2: PE-P1b Do not change this setting (Designed 3: PE-P1c for Factory Use). Displays the current brand ID Brand ID number. 00* – 7F Do not change this setting (Designed for Factory Use). Displays the current maintenance ID Mainte. ID number. 00* – 7F Do not change this setting (Designed for Factory Use). Registration 1.
PAGE 181
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Item Selections Remarks 1.32mm per step. Range is -5mm to +5mm. Horizontal (-15 to +15) step If the machine settings are reset to the factory defaults, this value does not change. The printer will exit the energy saver state after this setting is changed. Tray2 0.24mm per step. Range is -3.6mm to +3.6mm If the machine settings are reset to the factory defaults, this value does not change.
PAGE 182
CÓPIA NÃO CONTROLADA Smart Organizing Monitor (Printer Model) Item Selections Remarks 1.32mm per step. Range is -5mm to +5mm. Horizontal (-15 to +15) step If the machine settings are reset to the factory defaults, this value does not change. The printer will exit the energy saver state after this setting is changed. Duplex Tray 0.24mm per step. Range is -3.6mm to +3.6mm If the machine settings are reset to Vertical (-15 to +15) step the factory defaults, this value does not change.
PAGE 183
CÓPIA NÃO CONTROLADA Service Menu (MF Model) 5.3 SERVICE MENU (MF MODEL) 5.3.1 OVERVIEW The MF model has several service menus. Each service menu has several adjustment items. This section explains how to enter each service menu and what you can do in each service menu. Each menu is classified into two "Modes" depending on how you enter the service menus. "Menu Mode" can be executed by pushing a sequence of keys.
PAGE 184
CÓPIA NÃO CONTROLADA Service Menu (MF Model) 5.3.2 MAINTENANCE MODE MENU Entering the Maintenance Mode Menu 1. Turn on the machine. 2. Press these keys in the following order: "Clear/Stop", "1", "0", "7" and "Color Start" 3. "Maintenance Mode" is displayed on the LCD. Selecting an Item To select an item, press the "Up" or "Down" key. Going into the Next Level/ Returning to the Previous Level To go into the next level of an item, select an item then press the "OK" key.
PAGE 185
CÓPIA NÃO CONTROLADA Service Menu (MF Model) Displays the sum total of scanner counters for Scanner Counter each mode. Total Page/ Black Page/ Color Page / ADF Used Displays the number of paper jams at each Jam Counter location. Total/ ADF/ Printer Output Bin/ Internal/ Tray1 / Tray2 Displays the number of paper misfeeds with tray 1 Coverage or tray 2. Service Tables Coverage1 (Tray 1)/ Coverage2 (Tray2) Print Reports G3 protocol dump of the latest communication is G3 Protocol dump list printed.
PAGE 186
CÓPIA NÃO CONTROLADA Service Menu (MF Model) 00* – 7F Brand ID Displays the current brand ID number. Do not change this setting (Designed for Factory Use). 00* – 7F Maintenance ID Displays the current maintenance ID number. Do not change this setting (Designed for Factory Use). LSU Adjustment Input 160 bytes setting. Character: alphanumeric "0-9", "a-f", "A-F", only valid data can be input. Input length: 160 bytes When you execute "Trans. Belt Adjust", the transfer belt adjustment is Trans.
PAGE 187
CÓPIA NÃO CONTROLADA Service Menu (MF Model) Determines the maximum amount of ink/toner you can use in any area of your text. This is where you Text are controlling exactly how much ink will be used during printing. [200 to 400 / 250 (Default)/ 10/step] Setting 0: Off Determines the maximum amount of ink/toner you can use in any area of your graphic. This is where Toner Limit Graphic you are controlling exactly how much ink will be used during printing.
PAGE 188
CÓPIA NÃO CONTROLADA Service Menu (MF Model) 2nd Transfer Front Adjusts the transfer roller current, based on the default value. [-15 to 15 / 0 (Default) / 1 μA/step] 2nd Transfer 2nd Transfer Fuser Temp. Back Adjusts the transfer roller current, based on the default value. [-15 to 15 / 0 (Default) / 1 μA/step] Adjusts the temperature of the fusing unit, based Fuser Temperature on the default value. [-30 to 0 / 0 (Default) / 2°C/step] Adjusts the horizontal registration for tray 1. If the Horiz.
PAGE 189
CÓPIA NÃO CONTROLADA Service Menu (MF Model) Adjusts the vertical registration for the bypass tray. Vert.Bypass If the machine settings are reset to the factory defaults, this value does not change. [-15 to 15 / 0 (Default) / 0.3 mm/step] Adjusts the horizontal registration for the back side Horiz.Dup.Back in duplex mode. If the machine settings are reset to the factory defaults, this value does not change.
PAGE 190
CÓPIA NÃO CONTROLADA Service Menu (MF Model) Flatbed Main Reg. Adjusts the Flatbed Scan main-scan registration. (G181 doesn't support this.) [-2.0 to 2.0 / 0 (Default)/ 0.1 mm/step] Flatbed Sub Reg. Adjusts the Flatbed Scan sub-scan registration. (G181 doesn't support this.) [-2.0 to 2.0 / 0 (Default)/ 0.1 mm/step] Adjusts the ADF Scan main-scan magnification. ADF Main Reg. (G181 doesn't support this.) [-0.9 to 0.9 / 0 (Default)/ 0.1 %/step] Adjusts the ADF Scan sub-scan magnification. ADF Sub Reg.
PAGE 191
CÓPIA NÃO CONTROLADA Service Menu (MF Model) These selectors are used to improve the Cable Equalizer pass-band characteristics of analogue signals on the telephone line. [0Km (Default)/ 1.8Km/ 3.6Km/ 7.2Km] This sets the number of training retries to be Protocol Training Retries repeated before automatic fallback. [1 Time/ 2 Times (Default)/ 3 Times/ 4 Times] Definition Encoding Sets the compression method for Tx/Rx.
PAGE 192
CÓPIA NÃO CONTROLADA Service Menu (MF Model) Number of CNG cycles to be detected CNG Cycles This setting is only effective for FAX/TAD mode. [1.5 Cycle (Default)/ 2.0 Cycle] Determines the period when tones from the line Tone Sound are monitored. Monitoring [No Monitoring/ Up To Phase B (Default)/ All TX Phases] Pressing the Stop/Clear key can stop the current Stop/Clear key receiving operation. Received data is lost.
PAGE 193
CÓPIA NÃO CONTROLADA Service Menu (MF Model) This sets the number of pulses that are generated during dialing. Dial Pulse Setting Dial Pulse Type N: Dialing '0' generates 10 pulses --- Dialing '9' generates 9 pulses. N+1: Dialing '0' generates 1 pulse --- Dialing '9' generates 10 pulses. 10-N: Dialing '0' generates 10 pulses --Dialing '9' generates 1 pulse.
PAGE 194
CÓPIA NÃO CONTROLADA Service Menu (MF Model) This setting sets the time-out length for the 1st dial tone detection. The machine waits for a dial tone Timeout Length for the specified time and disconnects itself from the line when no dial tone is input.
PAGE 195
CÓPIA NÃO CONTROLADA Service Menu (MF Model) Rev. 07/05/2009 V34 Settings These selectors set the equalizer's training level to Equalizer be applied if training fails due to poor line connection. [Automatic (Default)/ 4 Points/ 16 Points] Redialing Resend when a communication error occurs. [Disabled (Default)/ Not Disabled] Sets the first transmission speed choice, before fallback.
PAGE 196
CÓPIA NÃO CONTROLADA Service Menu (MF Model) ⇒ Rev. 07/05/2009 The "Reseller Default" menu can be entered directly at power-on. If you want to enter this mode directly, try the following procedure SPC 232SF Reset Password. 1. Power OFF the unit. 2. Power ON the unit while holding down the “Copy” key. 3. Continue to hold down the “Copy” key until the display indicates “Factory Default Execute”. 4. Release the “Copy” key. 5.
PAGE 197
CÓPIA NÃO CONTROLADA Service Menu (MF Model) Rev. 07/05/2009 Menu List Fax Test (G181 does not support this menu.) On Hook Executes the on hook test. Off Hook Executes the off hook test CED Test CNG Test Executes the CED test. 1100 Hz Executes the CNG test ANSam Executes the ANSam test. Ring Tone Test Executes the ring tone test. DTMF Test Modem Test SM Tone [0] to [9] Executes the DTMF tone 0 to 9 test. Tone [*] Executes the DTMF tone * test. Tone [#] Executes the DTMF tone # test.
PAGE 198
CÓPIA NÃO CONTROLADA Firmware Updating 5.4 FIRMWARE UPDATING Do not turn off the main power of the machine during the firmware updating. If doing so, the engine board or controller board may be damaged. 5.4.1 PRINTER MODEL Controller Firmware 1. Start SOM. 2. Click the "Printer Configuration" button on the "User Tools" tab. 3. Input "Admin074" and click the "OK" button.
PAGE 199
CÓPIA NÃO CONTROLADA Firmware Updating Click the "Printer Firmware Update" button on the "Maintenance" tab. 5. Seek the location of the update file and select it, and then click the "Open" button. Service Tables 4.
PAGE 200
CÓPIA NÃO CONTROLADA Firmware Updating 6. SDC shows "Controller FW updating..." and the Alert LED (red) on the printer starts blinking. (The Ready LED remains lit.) 7. Wait for a few minutes. 8. When the update has finished, SDC shows "Controller FW download completed." and the Ready LED (green) on the printer starts blinking. (The Alert LED is still blinking.) If "Controller FW download completed" does not appear, the download failed. Try again.
PAGE 201
CÓPIA NÃO CONTROLADA Firmware Updating If power failed during the download, try again. If you still cannot download the firmware, it may be necessary to change the EGB and/or the controller board. 9. Turn the printer off and on. Engine Firmware Start SOM. 2. Click the "Printer Configuration" button on the "User Tools" tab. 3. Input " Admin074" and click the "OK" button. 4. Click the "Engine Firmware Update" button in the "SP Mode 1" tab. 5.
PAGE 202
CÓPIA NÃO CONTROLADA Firmware Updating 5.4.2 MF MODEL Checking the Machine Firmware Version 1. Turn the machine on. 2. If the printer driver is not installed on your PC, install the printer driver now. 3. Press "Menu" and select "Report Print" with the "Up" or "Down" key. 4. Press "OK" and select "Maintenance Page" with the "Up" or "Down" key. 5. Press "OK" to display the "Firmware version (Controller)" and "Engine FW version" Updating the Controller Firmware 1. Make a folder in your computer.
PAGE 203
CÓPIA NÃO CONTROLADA 5. The machine makes a beep sound when starting the firmware update. 6. The image above is displayed on the PC and "Firmware update" and "Updating" are displayed on the operation panel. 7. Then, you can close this window at your PC. Do not turn off the machine until "Done Please reboot" is displayed in the operation panel. Otherwise, the controller board will be damaged. If “Done Please reboot“ does not appear, the download failed. Try again.
PAGE 204
CÓPIA NÃO CONTROLADA Firmware Updating Updating the Engine Firmware 1. Make a folder in your computer. 2. Save the files (.”bin", .”fwu", .”ini" and .”exe") in the folder. 3. Click the exe file to execute the updating program. 4. Click "Eng. F/W Update (USB or NET)" to send the engine firmware from PC to MF printer. The "F/W Update (USB or NET)" buttons are for designer use only. Do not use these buttons. 5. The machine makes a beep sound when starting the firmware update. 6.
PAGE 205
CÓPIA NÃO CONTROLADA Firmware Updating If power failed during the download, try again. If you still cannot download the firmware, it may be necessary to change the EGB and/or the controller board. 5.4.3 BOOT LOADER FIRMWARE Service Tables This is also listed on the configuration page, but this firmware is not updated in the field.
PAGE 206
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 207
CÓPIA NÃO CONTROLADA DETAILED DESCRIPTIONS SECTION DETAILED DESCRIPTIONS REVISION HISTORY Page Date Added/Updated/New None CÓPIA NÃO CONTROLADA
PAGE 208
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 209
CÓPIA NÃO CONTROLADA Machine Overview 6. DETAILED DESCRIPTIONS SECTION 6.1 MACHINE OVERVIEW 6.1.1 COMPONENT LAYOUT 1. Laser Optics Housing Unit 2. Print Cartridge (AIO) 3. Development Roller (AIO) 4. Paper Exit 5. Fusing Unit 6. Fusing Lamp 7. Duplex Path 8. Transfer Roller SM 9. Registration Roller 10. By-pass 11. Paper Feed Roller 12. ITB (Image Transfer Belt) Unit 13. OPC (AIO) 14.
PAGE 210
CÓPIA NÃO CONTROLADA Machine Overview 6.1.
PAGE 211
CÓPIA NÃO CONTROLADA Machine Overview 1. Color AIO Motor 5. Registration Clutch 2. Black AIO Motor 6. Paper Feed Clutch 3. Duplex Motor (Duplex model only) 7. Agitator Motor 4. Transport/Fusing Motor 8. ITB (Image Transfer Belt) Contact Motor Color AIO Motor: This drives the color AIOs (Cyan, Magenta and Yellow) Black AIO Motor: This drives the black AIO and the ITB (Image Transfer Belt). Duplex Motor (Duplex model only): This drives the paper exit roller and the duplex roller.
PAGE 212
CÓPIA NÃO CONTROLADA Machine Overview Paper Feed Clutch: This transfers drive from the transport/ fusing motor to the paper feed roller. Agitator Motor: This moves the agitators in the waste toner bottle. ITB Contact Motor: This moves the ITB into contact with and away from the color OPCs.
PAGE 213
CÓPIA NÃO CONTROLADA Machine Overview 6.1.4 ELECTRICAL COMPONENT LAYOUT Engine 1 2 Parts Name Description Waste Toner Overflow This sensor detects whether the waste toner bottle is Sensor full. Waste Toner Bottle Set This sensor detects whether the waste toner bottle is Sensor set. 3 ITB Contact Sensor 4 Paper Exit Sensor 5 Paper End Sensor This sensor detects whether the image transfer belt is in contact with the color OPCs (C, M, Y).
PAGE 214
CÓPIA NÃO CONTROLADA Machine Overview No. Parts Name Description This board controls all of the machine, input/output, drivers 1 EGB (Engine Board) and input/output connections and the handshake with the Controller. 2 3 4 Controller Board This board controls the memory, all applications and all (printer model) peripheral devices. Temperature/Humidity This sensor detects the relative temperature and humidity Sensor around the machine.
PAGE 215
CÓPIA NÃO CONTROLADA Machine Overview PSU (Power Supply This supplies DC power for the EGB, fusing unit and Unit) interlock switches. 8 Main Switch This switch provides power to the machine. 9 Fusing Fan Motor This motor exhausts air around the fusing unit. 10 Interlock Switches 11 LSU Fan Motor These switches turn off DC power when the front cover or top cover is open. This motor exhausts air around the laser optics housing unit.
PAGE 216
CÓPIA NÃO CONTROLADA Machine Overview 6.1.5 BOARD STRUCTURE Printer Model Descriptions EGB (Engine Board): This controls the Engine, the controller interface, image processing, MUSIC (Mirror Unit for Skew and Interval Correction), input/output, interfaces with the optional units, and the operation panel. MUSIC is also called Automatic Line Position Adjustment). Controller: This controls the interface between the OPU and EGB, and applications.
PAGE 217
CÓPIA NÃO CONTROLADA Machine Overview MF Model EGB (Engine Board): This controls the Engine, the controller interface, image processing, MUSIC (Mirror Unit for Skew and Interval Correction), input/output, interfaces with the optional units, and the operation panel. MUSIC is also called Automatic Line Position Adjustment). Controller: This controls the interface between the OPU and EGB, ADF, Scanner unit and Component Interconnect Bus).
PAGE 218
CÓPIA NÃO CONTROLADA Machine Overview 6.1.6 PRINTING PROCESS This machine uses four AIOs and four laser beams for color printing. Each AIO contains a drum, charge roller, cleaning brush, blade, development roller and mixing auger. The toner image on each drum is moved to the image transfer belt. The four colors are put on the belt. All four toners are put on the belt at the same time. Then the completed four-color image is moved to the paper. 1.
PAGE 219
CÓPIA NÃO CONTROLADA Machine Overview 6. Quenching for the Development Roller: Charge is removed from the development roller with a quenching sheet in the AIO. There is no quenching for the OPC drum. 7. Paper Transfer and Separation: Toner transfers from the image transfer belt to the paper when the paper is fed between the image transfer belt and transfer roller. After transfer, the paper separates from the image transfer belt, because of a discharge plate immediately after the transfer roller. 8.
PAGE 220
CÓPIA NÃO CONTROLADA Process Control 6.2 PROCESS CONTROL 6.2.1 OVERVIEW This machine has these two forms of process control: Potential control Toner supply control Process control uses these components: Three TM (Toner Mark) sensors (left [A], center [B], and right [C]). Only the center TM sensor (direct-reflection and diffusion type) is used for process control. The left and right TM sensors (direct-reflection type) are used for line positioning and other adjustments.
PAGE 221
CÓPIA NÃO CONTROLADA Process Control 6.2.2 PROCESS CONTROL FLOW 1. TM sensor correction (Vsg adjustment) The center TM sensor checks the bare transfer belt's reflectivity and the machine calibrates the TM sensors. 2. Development bias control The machine makes a 7-gradation pattern on the transfer belt for each toner color. The pattern has 9 squares (the sequence is as follows: 7 yellow squares, 7 cyan squares, 7 magenta squares and 7 black squares).
PAGE 222
CÓPIA NÃO CONTROLADA Process Control 6.2.3 PROCESS CONTROL SELF-CHECK This machine does potential control with a procedure that is known as the process control self-check. This procedure is done at these 7 times. Timing Execution Mode 1. Initial Power-ON 2. Recovery form Sleep Mode 3. Front or Top Cover Open/Close 4. Ready Status Development Bias Control and MUSIC (approx. 55 seconds) MUSIC only (approx. 22 seconds) No Execution One of the control modes is executed at each timing.
PAGE 223
CÓPIA NÃO CONTROLADA Process Control 1) The previous MUSIC was done if there was a high temperature inside the machine. 3. Immediately after the front or top cover is closed No adjustment is done when the front or top cover is closed, if one of the following conditions occurs.
PAGE 224
CÓPIA NÃO CONTROLADA Process Control 7. Job end: Toner amount control and MUSIC start automatically after a job when the machine gets a request to execute the toner amount control and MUSIC. MUSIC starts automatically after a job when the machine gets a request to execute MUSIC.
PAGE 225
CÓPIA NÃO CONTROLADA Laser Exposure 6.3 LASER EXPOSURE 6.3.1 OVERVIEW 2. Fθ Lens 3. Polygon Mirror Motor 4. Synchronizing Detector Board 5. LD unit - K/Y This machine uses two LDB units and one polygon mirror motor to produce latent images on four OPC drums (one drum for each color toner). There are two hexagonal mirrors. The polygon mirror motor rotates the mirrors clockwise and each mirror reflects beams from the LD unit.
PAGE 226
CÓPIA NÃO CONTROLADA Laser Exposure 6.3.2 OPTICAL PATH The laser beams for magenta [B] and yellow [C] are sent to the upper part of the polygon mirror [E]. The laser beams for cyan [A] and black [D] are sent to the lower part of the polygon mirror.
PAGE 227
CÓPIA NÃO CONTROLADA Laser Exposure 6.3.3 LD SAFETY SWITCH A safety switch turns off when the front cover or the top cover is opened. As a result, the relay on the PSU cuts off the power supply (+5V) to the two LD boards. (The circuits go through the EGB.) This system prevents unexpected laser emission, and ensures user Detailed Descriptions Section safety and technician safety.
PAGE 228
CÓPIA NÃO CONTROLADA Laser Exposure 6.3.4 MUSIC (MIRROR UNIT SKEW AND INTERVAL CORRECTION) During MUSIC, the line patterns above are made 16 times for fine adjustment or 8 times for the rough adjustment on the transfer belt. The spaces between the lines (YY, KK, CC, MM, KY, KC, KM) are measured by the front, center, and rear TM sensors.
PAGE 229
CÓPIA NÃO CONTROLADA AIO (All In One) Cartridge 6.4 AIO (ALL IN ONE) CARTRIDGE 1. Waste Toner Container 9. Development Roller 2. Transport Belt Shaft 10. OPC 3. Waste Toner Collection Coil 11. Waste Toner Collection Coil 4. Toner Agitator 12. OPC Cleaning Blade 5. Upper Mixing Roller 13. Charge Roller Cleaner 2 6. Development Blade 14. Charge Roller 7. Lower Mixing Roller 15. Charge Roller Cleaner 1 8. Toner Supply Roller 16. Waste Toner Transport Belt This machine uses the AIO system.
PAGE 230
CÓPIA NÃO CONTROLADA AIO (All In One) Cartridge 6.4.2 DRIVE The black AIO motor drives the gear [A] for the black AIO. The color AIO motor drives the gears [B] and color gears [C] for the cyan, magenta and yellow AIOs through gears. Each of these gears engages with a gear [D] in the OPC, and this gear drives the rollers in the AIO through other gears.
PAGE 231
CÓPIA NÃO CONTROLADA AIO (All In One) Cartridge 6.4.3 OPC CHARGE AND CLEANING This machine uses a charge roller [A]. The charge roller gives the drum surface a negative charge. The high voltage supply board, which is at the left side of the machine, applies a dc and ac voltage (at a constant current) to the roller. The ac voltage helps to make sure that the charge given to the drum is as constant as possible. The machine automatically controls the charge roller voltage when process control is done.
PAGE 232
CÓPIA NÃO CONTROLADA AIO (All In One) Cartridge 6.4.4 WASTE TONER COLLECTION FROM THE OPC The waste toner collection coil [A] transports waste toner from the OPC to the right side of the AIO. After that, the waste toner transport belt [B], which is driven by the transport belt shaft [C], lifts waste toner up to the waste toner tank [E]. The collected waste toner is moved to the left side of the AIO by the waste toner collection coil [D] and transport belt shaft [C].
PAGE 233
CÓPIA NÃO CONTROLADA AIO (All In One) Cartridge 6.4.5 TONER MIXING AND TRANSPORT The toner moves as shown in the above drawing. The toner agitator [A] mixes the toner so that it is transported evenly to the mixing rollers. The upper mixing roller [B] moves toner to the center, then the lower mixing roller [C] moves toner to the right and left sides. Finally, the toner supply roller [D] supplies toner to the development roller.
PAGE 234
CÓPIA NÃO CONTROLADA AIO (All In One) Cartridge 6.4.6 DEVELOPMENT MECHANISM This machine does not use developer, so a TD sensor is not necessary. In each AIO unit, the toner supply roller [A] supplies toner to the development roller [B].
PAGE 235
CÓPIA NÃO CONTROLADA Paper Feed 6.5 PAPER FEED 6.5.1 OVERVIEW 1. Paper Feed Roller 4. Paper Height Lever 2. Registration Sensor 5. Separation Pad 3. Registration Roller 6. Paper End Sensor This machine has a paper tray (250 sheets) and a by-pass paper feed (single sheet). The paper feed mechanism uses a friction pad system. The paper end sensor detects whether paper is installed in the tray and whether the tray is This machine also does not have automatic paper size detection.
PAGE 236
CÓPIA NÃO CONTROLADA Paper Feed 6.5.2 DRIVE AND PAPER END DETECTION Paper Feed The transport/fusing motor [A] controls the paper feed roller [B] and registration roller [C] with the paper feed clutch [D], registration clutch [E] and gears. (The transport/fusing motor also controls the fusing unit and paper exit roller.) The paper feed roller feeds a sheet of paper to the registration roller [C].
PAGE 237
CÓPIA NÃO CONTROLADA Paper Feed 6.5.3 TRAY LIFT The bottom plate [A] is lifted by the springs [B] in the tray when the tray is inserted in the machine, and the bottom tray lock lever [C] is released by the projection [D] at the right side you must press the bottom plate down when you insert the tray in the machine. SM 6-29 G165/G166/G167/G181/G183/G184 CÓPIA NÃO CONTROLADA Detailed Descriptions Section of the tray set location. There is no tray lowering mechanism for these models.
PAGE 238
CÓPIA NÃO CONTROLADA Paper Feed 6.5.4 BY-PASS FEED This machine uses a manual by-pass feed system. When the registration sensor [A] detects a sheet of paper [B] but no job has come in from a PC, the machine determines that the user has put a sheet of paper in the by-pass tray.
PAGE 239
CÓPIA NÃO CONTROLADA Paper Feed 6.5.5 DUPLEX (G167/G183/G184 ONLY) Drive The duplex motor [A] feeds out paper to the output tray in single-sided mode and also feeds paper to the duplex path in duplex mode. When a sheet [B] of paper passes through the paper exit sensor [C] in duplex mode, the duplex motor stops and rotates in reverse. The paper exit roller [D] feeds a sheet of paper to the duplex path.
PAGE 240
CÓPIA NÃO CONTROLADA Image Transfer 6.6 IMAGE TRANSFER 6.6.1 OVERVIEW 1. Image Transfer Belt 3. ITB Drive Roller 2. ITB (Image Transfer Belt) Roller 4. ITB Cleaning Unit The toner is moved from the four OPC drums to the image transfer belt. For a full color print, all four colors are moved from the PCUs to the transfer belt at the same time. The transfer roller then moves the four-color toner image from the transfer belt to the paper.
PAGE 241
CÓPIA NÃO CONTROLADA Image Transfer 6.6.2 DRIVE AND TRANSFER BELT ROLLER BIAS The black AIO motor [A] controls the transfer belt drive roller [B]. The belt tension roller [C] adds tension to the transfer belt to help to turn this belt. The image transfer belt rollers [D] are charged from terminal plates to move the toner from Detailed Descriptions Section the PCUs to the image transfer belt.
PAGE 242
CÓPIA NÃO CONTROLADA Image Transfer 6.6.3 TRANSFER BELT CONTACT The transfer belt does not touch the color OPC drums (cyan, magenta and yellow) when the machine makes a black and white print. The transfer belt contact motor [B] turns the CMY contact cam shaft [C] when the machine starts to make a color print. The CMY contact cams slide the right and left sliders [D] and these sliders lift the belt transfer rollers for each OPC drum (CMY) to the transfer belt.
PAGE 243
CÓPIA NÃO CONTROLADA Image Transfer 6.6.4 ITB (IMAGE TRANSFER BELT) CLEANING UNIT The ITB cleaning blade [A] in the cleaning unit removes remaining toner on the image transfer belt after image transfer to the paper. The toner collection coil [B] moves the collected waste toner to the outlet for the waste toner bottle. The ITB cleaning unit has a shutter mechanism at the outlet for the waste toner bottle.
PAGE 244
CÓPIA NÃO CONTROLADA Image Transfer 6.6.5 TRANSFER ROLLER OVERVIEW 1. Transfer Roller 2. Image Transfer Belt 3.
PAGE 245
CÓPIA NÃO CONTROLADA Image Transfer 6.6.6 PAPER TRANSFER AND DISCHARGE Transfer Roller The transfer roller [A] is always pressed against the image transfer belt by pressure from a spring. The transfer roller moves toner images [B] from the transfer belt to the paper. When a sheet of paper [C] goes between the transfer roller and the transfer belt, the transfer roller turns with the paper. Paper Transfer Bias The high voltage power supply (HVPS) supplies electricity to the transfer roller.
PAGE 246
CÓPIA NÃO CONTROLADA Image Transfer 6.6.7 WASTE TONER COLLECTION The waste toner collection coil [A] moves collected waste toner from the ITB (image transfer belt) unit to the entrance [B] of the waste toner bottle. The agitator plate [C] levels the collected waste toner in the waste toner bottle. It is driven by the agitator motor [D]. The waste toner bottle set sensor [E] detects whether the waste toner bottle is set.
PAGE 247
CÓPIA NÃO CONTROLADA Fusing and Exit 6.7 FUSING AND EXIT 1. Paper Exit Sensor 6. Thermistor (Center) 2. Paper Exit Roller 7. Fusing Lamp 3. Pressure Release Lever 8. Thermostat 4. Stripper Plate 9. Hot Roller 5. Pressure Roller 10. Thermistor (Right) SM 6-39 G165/G166/G167/G181/G183/G184 CÓPIA NÃO CONTROLADA Detailed Descriptions Section 6.7.
PAGE 248
CÓPIA NÃO CONTROLADA Fusing and Exit 6.7.2 DRIVE Models without Duplex (G165/G166: Printer model, G181: MF model) The transport/fusing motor [A] drives the hot roller [B], pressure roller [C] (this is an idle roller) and paper exit roller [D] (via gears). The paper exit sensor [E] detects the trailing edge of the paper to determine the stop timing for the transport/fusing motor. It also checks whether a paper jam occurs at the fusing unit or paper exit.
PAGE 249
CÓPIA NÃO CONTROLADA Fusing and Exit [B]. This is because the duplex motor controls paper exit and feed in the duplex. The paper exit sensor [C] detects the trailing edge of the paper to determine the stop timing for the transport/fusing motor, reverse timing, and stop timing for the duplex motor. It also checks whether a paper jam occurs at the fusing unit or paper exit. 6.7.3 PRESSURE RELEASE MECHANISM The springs always apply the correct pressure to the nip between the pressure roller and hot roller.
PAGE 250
CÓPIA NÃO CONTROLADA Fusing and Exit [A]: Idling ready temperature (100°C) The fusing unit starts to rotate (idling) for 54 seconds [a]. [B]: Print ready temperature (170°C) This is the temperature to wait for a print job [b]. [C]: Target temperature after 1st print (This depends on the target temperature of each paper type; see the table below) The machine keeps this temperature for printing (c) after the 1st print time (d: 14 seconds).
PAGE 251
CÓPIA NÃO CONTROLADA Fusing and Exit Target Temperature for Each Paper Type Paper Type Target Temperature Thin 175°C Plain 1 180°C Recycled 180°C Plain and Recycled 180°C Plain 2 175°C Thick 1 175°C Cardstock 175°C Bond 175°C Envelopes 170°C Fusing unit related SC codes If one of the fusing unit components (such as thermistors, thermostat, fusing lamp etc.) is defective, the following SC codes may be issued.
PAGE 252
CÓPIA NÃO CONTROLADA Fusing and Exit Energy Saver There are two modes for energy saving. Low power mode (Energy Saver Mode 1): This keeps the fusing temperature at 155°C for a specified time (adjustable with "Power Saver" in the user mode) while the machine waits for the next print job. Sleep mode (Energy Saver Mode 2): This turns off power to the engine unit after the time specified with "Power Saver" has passed.
PAGE 253
CÓPIA NÃO CONTROLADA Controller 6.8 CONTROLLER 6.8.1 OVERVIEW The printer model has two types of controllers: GDI and PCL. The MF model has the main controller and the extension PDL controller. Controller: Printer model (G165/G166/G167) CPU 195MHz (PE-P1a) 300MHz (PE-P1b/c) 64MB (PE-P1a) Std. 128MB (PE-P1b/c) RAM 64MB (PE-P1a) Max. Hard Disk Drive PDL 384MB (PE-P1b/c)*1 - - PE-P1a: DDST (GDI) PE-P1b/c: PCL5c/6, PostScript 3 emulation PCL: Fonts 1 bitmap font. Std.
PAGE 254
CÓPIA NÃO CONTROLADA Controller Standard MIB (SMNP Printer MIB-II (RFC1213), HostResource (RFC1514), PrinterMib (RFC1759) MIB) Windows 98se/NT4.0/2000/Me/XP/Server 2003 Operating Systems/Network Mac OS 9/x, 10.1-10.
PAGE 255
CÓPIA NÃO CONTROLADA Controller 1.English, 2.German, 3.French, 4.Italian, 5.Spanish, Test Page Config. Map 6.Dutch, 7.Swedish, 8.Norwegian, 9.Danish, 10.Czech, 11.Hungarian, 12.Finnish, 13.Polish, 14.
PAGE 256
CÓPIA NÃO CONTROLADA Controller Controller: MF model (G181/G183/G184) CPU ARM11 400MHz PE-MF1a/b: 128MB, PE-MF1c: 256MB (128MB Std. for printer function) RAM 512MB (Only PE-MF1c, 384MB for printer Max. Hard Disk Drive PDL function) - - PE-MF1a/b: DDST (GDI) PE-MF1c: PCL5c/6, PostScript 3 emulation PCL: 41 Symbolset, 35 Intellifonts, 10 TrueType fonts, Fonts 1 bitmap font. Std. PS3: 80 fonts (Only PE-MF1c) Host Interface Std. USB2.
PAGE 257
CÓPIA NÃO CONTROLADA Controller Print Resolution 600 x 600 dpi, 1200 x 600 dpi equivalent, 2400 x 600 dpi Engine equivalent PCL5c Controller PCL6 PS3 PCL5c Drivers PCL6 equivalent 600 x 600 dpi, 1200 x 600 dpi equivalent, 2400 x 600 dpi equivalent 600 x 600 dpi, 1200 x 600 dpi equivalent, 2400 x 600 dpi equivalent 600 x 600 dpi, 1200 x 600 dpi equivalent, 2400 x 600 dpi equivalent 600 x 600 dpi, 1200 x 600 dpi equivalent, 2400 x 600 dpi equivalent 600 x 600 dpi, 1200 x 600 dpi equivalent, 2400 x 6
PAGE 258
CÓPIA NÃO CONTROLADA Controller Language Operation 1.English, 2.German, 3.French, 4.Italian, 5.Spanish, Panel 6.Dutch, 7.Swedish, 8.Norwegian, 9.Danish, 10.Finnish, (LCD) 11.Portuguese 1.English, 2.German, 3.French, 4.Italian, 5.Spanish, PCL5c/PCL6 6.Dutch, 7.Swedish, 8.Norwegian, 9.Danish, 10.Czech, 11.Hungarian, 12.Finnish, 13.Polish, 14.Portuguese, 15.Russian, 16.Simplified Chinese 1.English, 2.German, 3.French, 4.Italian, 5.Spanish, Drivers PS3 6.Dutch, 7.Swedish, 8.Norwegian, 9.Danish, 10.
PAGE 259
CÓPIA NÃO CONTROLADA ADF 6.9 ADF 6.9.1 OVERVIEW 1. Feed Sensor 2. Feed Roller 3. Separation Roller 6. Original Set Sensor 7. DF Exposure Glass Detailed Descriptions Section 4. Pick-up Roller 5.
PAGE 260
CÓPIA NÃO CONTROLADA ADF 6.9.2 PAPER PATH After the original set sensor has detected an original and the machine has received a copying or scanning job, the ADF motor rotates to pick up and feed a sheet of the original to the feed sensor. If the feed sensor does not detect paper after this sequence, the machine determines an original jam has occurred. The ADF motor stops when the feed sensor detects paper, and then starts to rotate again.
PAGE 261
CÓPIA NÃO CONTROLADA ADF 6.9.
PAGE 262
CÓPIA NÃO CONTROLADA ADF Feed out jam detection (Upper line: ON, Lower line: OFF) [A]: Checks for a Feed-in Jam (40000 pulses) [B]: Number of pulses for motor start to Start Scanning [C]: Checks for a Feed-out Jam (40000 pulses) [D]: Number of pulses for Paper feed out G165/G166/G167/G181/G183/G184 6-54 CÓPIA NÃO CONTROLADA SM
PAGE 263
CÓPIA NÃO CONTROLADA Scanner 6.10 SCANNER 6.10.1 OVERVIEW 1. Scanner Carriage Unit 2. DF Exposure Glass 5. White Plate Detailed Descriptions Section 3. Exposure Glass 4.
PAGE 264
CÓPIA NÃO CONTROLADA Scanner 6.10.2 DRIVE The scanner motor [A] drives the scanner carriage unit [B] through gears and a timing belt [C]. The scanner carriage unit moves along the carriage drive bar [D]. The carriage home position sensor [E] in the scanner carriage unit detects the home position when initializing the scanner or before/after scanning. The scanner carriage unit moves to read the white plate every scan to adjust white level (ADS).
PAGE 265
CÓPIA NÃO CONTROLADA SPECIFICATIONS SPECIFICATIONS REVISION HISTORY Page Date Added/Updated/New None CÓPIA NÃO CONTROLADA
PAGE 266
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 267
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 268
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 269
CÓPIA NÃO CONTROLADA General Specifications 7. SPECIFICATIONS 7.1 GENERAL SPECIFICATIONS 7.1.1 PRINTER MODEL PE-P1a: G165, PE-P1b: G166, PE-P1c: G167 Type Desktop Laser beam scanning and electro-photographic printing Technology Mono-component toner development 4-drum tandem method 600 × 600 dpi Speed (1bit) Resolution (dpi) 600 × 600 dpi Standard (2bits) 600 × 600 dpi Fine (4bits) General Speed Paper First Print Speed (A4/LT, SEF, Std. Tray) Duplex Printing A4/LT FC: PE-P1a:16ppm (LT:16.
PAGE 270
CÓPIA NÃO CONTROLADA General Specifications Op. Paper Tray Paper Feed Unit PE-P1a: up to 251 sheets, PE-P1b/c: up to 751 Max Output Standard capacity Tray PE-P1b/c: 500 sheets x 1 sheets Face down Up to 150 sheets (A4/LT or 80g/m2,20lb) A4,B5,A5,B6,A6,Legal,Letter,HLT,Exective, Standard Tray Foolscap, Folio Custom size: Min. 90mm x 148mm (3.6" x 5.92"), Max. 216mm x 356mm (8.64" x 14.
PAGE 271
CÓPIA NÃO CONTROLADA General Specifications NA version Max. Energy Saver Power Consumption EU version Max.
PAGE 272
CÓPIA NÃO CONTROLADA General Specifications 7.1.2 MF MODEL Engine PE-MF1a: G181, PE- MF1b: G183, PE- MF1c: G184 Type Desktop Flatbed with CCD array image-sensor Laser beam scanning and electro-photographic printing Technology Mono-component toner development 4-drum tandem method 600 × 600 dpi Speed (1bit) Resolution (dpi, bit/pixel) 600 × 600 dpi Standard (2bits) 600 × 600 dpi Fine (4bits) Printing General Speed Paper First Print Mono 14.0 sec or less F/C 14.
PAGE 273
CÓPIA NÃO CONTROLADA General Specifications Op. Paper Tray Paper Feed Unit PE-MF1a: up to 251 sheets, Max Output Standard capacity Tray PE- MF 1b/c: 500 sheets (80 g/m2) x 1 PE- MF 1b/c: up to 751 sheets Face down up to 150 sheets (A4/LT or 80g/m2, 20lb) A4, B5, A5, B6, A6, Legal, Letter, HLT, Executive, Foolscap, Folio Standard Tray Custom size: Min. 90mm x 148mm (3.6" x 5.92"), Max. 216mm x 356mm (8.64" x 14.
PAGE 274
CÓPIA NÃO CONTROLADA General Specifications 35 sheets (80g/m2, 20lb) Capacity ADF Original size Original weight Rating Power NA version Spec. version Power Consumption EU version Mode 52 - 105 g/m2 (14 - 28lbs.) 220 to 240V, 50/60Hz Max. 1300W or less Energy PE-MF1a/b 20 W or less Saver PE-MF1c 25 W or less Max. 1300W or less Energy PE-MF1a/b 20 W or less Saver PE-MF1c 25 W or less Warm-up Time Energy Save Length: 139.7-355.6 mm (5.
PAGE 275
CÓPIA NÃO CONTROLADA General Specifications Copier 1st copy speed Platen/ADF B&W: Less than 30 sec. FC: Less than 30 sec. A4 (210 x 297mm) / Letter (215.9 x Platen 279.4mm) Maximum original size A4 (210 x 297mm) / Letter (215.9 x ADF 279.4mm)/ Legal (215.9 x 355.6mm) PE-MF1a: B/W: 16 cpm (A4), 16.5 cpm (LT) FC: 16 cpm (A4), 16.
PAGE 276
CÓPIA NÃO CONTROLADA General Specifications Custom 25 – 400% in 1% steps Image density adjustment Yes, Manual only: 5 levels Copy mode Text/Photo/Mixed Memory copy Yes Auto-duplex copy No Interrupt copy No Combine copy 2 in 1, 4 in 1 (Only ADF) APS/AMS No/No Auto Tray Switch No Directional Magnification No Directional Size Magnification No Photo Mode Yes Auto Start No User Program No Electronic Sorting Standard (collation, ADF only) Image Rotation No Series Copy No G165/G1
PAGE 277
CÓPIA NÃO CONTROLADA General Specifications Scanner Scanning Device CCD array image-sensor Scanner: 1200 x 1200 dpi Resolution Driver: Max. 19200 x 19200 dpi (interpolated) Gray scale 256 levels ADF: B/W: less than 5 sec. / Gray Scale: less than 5 sec. / Color: less than 10 sec Scan modes/ speed (A4, 300dpi, USB2.0) Platen B/W: less than 5 sec. / Gray Scale: less than 5 sec.
PAGE 278
CÓPIA NÃO CONTROLADA General Specifications Fax Circuit PSTN/ PABX Compatibility: ITU-T Group 3 Coding system: MH/MR/MMR Modem speed: Automatic Fallback: 33600 bps Platen: A4/ LT/ LG Width max: 216 mm (8.5"), Length max: 297 mm (11.7") Document size: ADF: A4/ LT/ DLT Width: 139.7-215.9mm (5.5” - 8.5”) Length: 139.7-355.6 mm (5.5” - 14”) Scanning width: Max. 210 mm (8.3") Printing width: Max. 208 mm (8.
PAGE 279
CÓPIA NÃO CONTROLADA General Specifications One-touch dial: 20 (10 x 2) Broadcasting: 100 stations Communication Public switched telephone network source: PC Fax utility: Not available Automatic re-dial 5/4/3/2 times after 5 minutes (Default 5 times) Auto Answer 1-99 rings (Default 2 rings) 7.1.3 OPTION Paper Feed Unit Paper Tray A4,Letter Paper Weight 60-105g/m2 (16-28lb) Paper capacity 500 sheets x 1 tray Dimensions (W x D x H) 400 x 450 x 127mm/16 x 18 x 5.08 inch Weight 6 kg/13.
PAGE 280
CÓPIA NÃO CONTROLADA Supported Paper Sizes 7.2 SUPPORTED PAPER SIZES Supported and the size is molded in the tray. Need to select paper size by A operation panel/driver. Supported but size is not molded in the tray. Need to select paper size by B operation panel/driver. C Need to input paper size by operation panel and driver. N Not supported. Input Tray Type SEF/ LEF Size Option Auto. Standard Paper Bypass Tray Feed Tray Dup.
PAGE 281
CÓPIA NÃO CONTROLADA Supported Paper Sizes Input Tray Type SEF/ LEF Size Option Auto. Standard Paper Bypass Tray Feed Tray Dup.
PAGE 282
CÓPIA NÃO CONTROLADA Supported Paper Sizes Input Tray SEF/ Type LEF Size Option Auto. Standard Paper Bypass Tray Feed Tray Dup.*1 Unit DL Env SEF Width 110 x 220 90-216mm (3.6”x 8.5”) C N C N C N C N N C N 148 – Custom Length 356mm (5.8”x C 14.24”) *1: Automatic duplex cannot be used in MF copy mode.
PAGE 283
CÓPIA NÃO CONTROLADA Machine Configuration 7.3 MACHINE CONFIGURATION 7.3.1 PRINTER MODEL (G165/G166/G167) Duplex Optional Optional DDST PCL Unit Memory Tray (G849) (GDI) PS PE-P1a (G165) Manual N N Y N PE-P1b (G166) Manual Y 500x1 N Y PE-P1c (G167) Auto Y 500x1 N Y Models Specifications 7.3.
PAGE 284
CÓPIA NÃO CONTROLADA Machine Configuration Duplex Optional Optional DDST PCL Unit Memory Tray (G849) (GDI) PS PE-MF1a (G181) Manual N N Y N N PE-MF1b (G183) Auto N 500x1 Y N Y PE-MF1c (G184) Auto Y 500x1 N Y Y Models G165/G166/G167/G181/G183/G184 7-16 CÓPIA NÃO CONTROLADA Fax SM
PAGE 285
CÓPIA NÃO CONTROLADA PAPER FEED UNIT TK1010 (G849) PAPER FEED UNIT TK1010 (G849) REVISION HISTORY Page Date Added/Updated/New None CÓPIA NÃO CONTROLADA
PAGE 286
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 287
CÓPIA NÃO CONTROLADA PAPER FEED UNIT TK1010 (G849) TABLE OF CONTENTS 1. REPLACEMENT AND ADJUSTMENT .......................................1 1.1 PAPER FEED UNIT .................................................................................1 1.1.1 TOP COVER...................................................................................1 1.1.2 PAPER FEED AND RELAY CLUTCH ............................................1 1.1.3 PAPER END AND RELAY SENSOR..............................................2 1.1.
PAGE 288
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 289
CÓPIA NÃO CONTROLADA Read This First Safety and Symbols Replacement Procedure Safety Turn off the main power switch and unplug the machine before beginning any of the replacement procedures in this manual. Symbols Used in this Manual This manual uses the following symbols.
PAGE 290
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 291
CÓPIA NÃO CONTROLADA Paper Feed Unit 1. REPLACEMENT AND ADJUSTMENT Paper Feed Unit TK1010 (G849) 1.1 PAPER FEED UNIT 1.1.1 TOP COVER 1. Top left cover [A] ( x 1) 2. Top cover [B] ( x 6) 1.1.2 PAPER FEED AND RELAY CLUTCH 1. Top cover ( 2. Paper feed clutch [A] ( x 1, 3.
PAGE 292
CÓPIA NÃO CONTROLADA Paper Feed Unit 1.1.3 PAPER END AND RELAY SENSOR 1. Top cover ( 2. Paper end sensor [A] (hooks, 3.
PAGE 293
CÓPIA NÃO CONTROLADA Paper Feed Unit 1.1.4 PAPER FEED ROLLER 1. Top cover ( Top Cover) 2. Paper feed clutch ( 3. Paper guide [A] (hooks) 4. Remove the e-ring [B] at the right edge of the feed roller shaft. 5. Slide the paper feed roller [C] to the right side (hook). 6. Pull out the feed roller shaft [D] to the left side (bushing x 1).
PAGE 294
CÓPIA NÃO CONTROLADA Paper Feed Unit When reassembling If the feed roller shaft [A] cannot be inserted easily, pull the gear [B], and then insert the feed roller shaft.
PAGE 295
CÓPIA NÃO CONTROLADA Paper Feed Unit Paper Feed Unit TK1010 (G849) 1.1.5 FRICTION PAD 1. Pull out the tray [A] 2. Press down the bottom plate [B] 3. Friction pad [C] (hooks, spring x 1) When reassembling When re-installing the friction pad, make sure that the mylar [A] does not go under the friction pad.
PAGE 296
CÓPIA NÃO CONTROLADA CÓPIA NÃO CONTROLADA
PAGE 297
CÓPIA NÃO CONTROLADA Overview 2. DETAILED SECTION DESCRIPTIONS Paper Feed Unit TK1010 (G849) 2.1 OVERVIEW 2.1.1 COMPONENT LAYOUT 1. Side Fence 2. Paper End Sensor 3. Paper Feed Roller 4. Relay Sensor 5. Relay Roller SM 6. Friction Pad 7. Paper Height Lever 8. Bottom Plate 9.
PAGE 298
CÓPIA NÃO CONTROLADA Basic Operation 2.2 BASIC OPERATION 2.2.1 PAPER SEPARATION AND FEED The paper tray holds 500 sheets of paper. The paper feed unit uses a friction pad system. The gear [A] is driven by the transport/fusing motor in the mainframe. The relay clutch [B] and paper feed clutch [C] control drive from the mainframe. When the optional tray is selected as the feed tray, the relay clutch and paper feed clutch transmit drive power to the relay roller and paper feed roller.
PAGE 299
CÓPIA NÃO CONTROLADA Basic Operation Paper Feed Unit TK1010 (G849) 2.2.2 PAPER LIFT The bottom plate is always pressed up by the spring in the tray. Therefore, you must press down the bottom plate when you insert the tray in the machine. The bottom tray lock levers [A] hold the tabs [B] under the bottom plate after the bottom plate is pressed down.
PAGE 300
CÓPIA NÃO CONTROLADA Basic Operation 2.2.3 PAPER END DETECTION There is a paper end sensor [A] in the tray. The feeler [B] drops into the cutout [C] in the bottom plate and the actuator interrupts the paper end sensor. This sensor also detects whether the tray is set.