Image Scanner Operating Instructions Guide to Components Setting up the Scanner Installing Software Setting Originals Using the TWAIN Driver Appendix Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety Information in this manual before using the machine.
Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy place for quick reference. Two kinds of size notation are employed in this manual. With this machine refer to the inch version. Important Contents of this manual are subject to change without prior notice.
TABLE OF CONTENTS Safety Information ................................................................................................. 1 Safety During Operation............................................................................................. 1 Energy Star Program ............................................................................................. 4 Manuals for This Scanner .....................................................................................5 How to Read This Manual ....
Installing QuickScan............................................................................................43 System Requirements.............................................................................................. 43 Installing QuickScan................................................................................................. 43 4. Setting Originals Sizes and Weights of Recommended Originals................................................45 Original Sizes Available for Auto Detection.
Safety Information When using this machine, the following safety precautions should always be followed. Safety During Operation In this manual, the following important symbols are used: R WARNING: Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury. R CAUTION: Indicates a potentially hazardous situation which, if instructions are not followed, may result in minor or moderate injury or damage to property.
R WARNING: • Connect the Power Cord directly into a wall outlet and never use an extension cord. • Disconnect the power plug (by pulling the plug, not the cable) if the power cable or plug becomes frayed or otherwise damaged. • To avoid hazardous electric shock or laser radiation exposure, do not remove any covers or screws other than those specified in this manual.
R CAUTION: • Protect the equipment from dampness or wet weather, such as rain, snow, and so on. • Unplug the Power Cord from the wall outlet before you move the equipment. While moving the equipment, you should take care that the Power Cord will not be damaged under the equipment. • When you disconnect the power plug from the wall outlet, always pull the plug (not the cable). • Do not allow paper clips, staples, or other small metallic objects to fall inside the equipment.
Energy Star Program As an ENERGY STAR Partner, we have determined that this machine model meets the ENERGY STAR Guidelines for energy efficiency. The ENERGY STAR Guidelines intend to establish an international energy-saving system for developing and introducing energy-efficient office equipment to deal with environmental issues, such as global warming. When a product meets the ENERGY STAR Guidelines for energy efficiency, the Partner shall place the ENERGY STAR logo onto the machine model.
Manuals for This Scanner The following manuals describe the operational and maintenance procedures of this machine. To enhance safe and efficient operation of this scanner, all users should read and follow the instructions carefully. ❖ Quick Installation Guide Describes how to install the scanner. ❖ Operating Instructions (this manual) Provides all of the information how to install, set up, and use the scanner. This manual is provided as a PDF file. Note ❒ There is a CD-ROM that comes with this scanner.
How to Read This Manual Symbols The following set of symbols is used in this manual. R WARNING: This symbol indicates a potentially hazardous situation that might result in death or serious injury when you misuse the machine without following the instructions under this symbol. Be sure to read the instructions, all of which are described in the Safety Information section.
1. Guide to Components Guide to This Scanner ADC002S 1. ADF (Automatic Document Feeder) Allows you to automatically load multiple originals into this machine. 2. Paper Thickness Changeover Lever When you scan the thick originals — originals thicker than 128g/m2 (242.5bls) — with the ADF, set the paper thickness changeover lever to your side. After scanning, return the switch to the back side. 3. Original Table Set originals here to be loaded into this machine using ADF. 4.
Guide to Components 1 ADC003S 1. Pressure Panel 6. Lock Screw Holds the originals down on the Exposure Glass. This is to lock the scanning parts inside when you transport this machine. Remove this screw when you set up this machine. 2. Background Panel for Exposure Glass Panel to set the background color for the original in black or white when you place the original on the exposure glass. ⇒ p.54 “Changing the Color of the Background Panel for the Exposure Glass” 7. USB 2.0 Interface Connector 3.
Guide to This Scanner Understanding Indicators This section explains how to interpret the indicators in front of this machine.
Guide to Components DIP Switches Change only the switches No. 1 to 3. Do not change the other switches. 1 ADC005S SW No. Function OFF ON 1 SCAM *1 disable enable 2 SCSI synchronous transmission enable disable 3 SCSI termination enable disable 4 5 6 (system usage) always OFF Do not make changes. 7 8 *1 SCAM: SCSI Configured Automatically. Protocol to set SCSI ID automatically.
2. Setting up the Scanner This section explains how to setup the scanner to get it ready for use, and how to make necessary connections. Confirmations Before the Setup Location, Space and Environment ❖ Location R WARNING: • Make sure the wall outlet is near the machine and easily accessible so that in event of an emergency it can be unplugged easily. R CAUTION: • Keep the machine away from humidity and dust. A fire or an electric shock might occur.
Setting up the Scanner ❖ Environment Important ❒ Do not set up the scanner in any of the following types of locations. It may be the cause of the malfunction.
Confirmations Before the Setup Disengaging the lock for transportation In this section, we explain how to disengage the lock after you take the scanner out of the package for transportation. A Remove two lock screws fixed on the back of this machine. 2 ADC082S Note ❒ Use a coin to remove the lock screws. ❒ Be sure to remove the lock screws. Turning the power on without removing the screws could result not only in failure in scanning, but in malfunction of this machine.
Setting up the Scanner C The removed lock screws are to be kept on the back of the Pressure Panel as follows: A Lift the Pressure Panel and carefully pull out the Background Panel that is fixed with the Velcro. 2 ADC071S B The removed screws are to be kept fixing on the back of the Pressure Panel. ADC086S C Return the removed Background Panel to where it was. Reference Regarding how to set the Background Panel, please refer to the step B E of p.
Confirmations Before the Setup Note ❒ Be sure to set the lock lever to the “Unlock” position. Turning the power on leaving the lock lever to the “Lock” position could result not only in failure in scanning but in malfunction of the machine.
Setting up the Scanner Installing Options Installing the Image-Processing Unit Important ❒ Touch any metallic material before touching the image-processing unit to remove static from your body. 2 Note ❒ Use the accessory tool to remove or fix the screws. A Turn OFF the power to this product and disconnect all cables connected to the product, including the power cable. B Remove the three screws on the lower back surface of the product.
Installing Options D Remove the seven screws on the cover of the scanner control unit. 2 ADC064S E Open the cover of the scanner control unit. ADC011S F Connect the connector at the bottom surface of the image-processing unit to the connector of the scanner control unit, and fix with one accessory screw. ADC012S G Check that it is connected tightly, check that there are no foreign objects such as metal on the scanner control unit.
Setting up the Scanner I Fix the scanner control unit with three screws. J Removed cables must connect in former state. Installing the IEEE1394 Interface Board Important ❒ Touch any metallic material before touching the IEEE interface board to remove static from your body. 2 Note ❒ The optional IEEE 1394 interface board is alternatively used with the USB interface board. A Turn OFF the power to this product and disconnect all cables connected to the product, including the power cable.
Installing Options D Remove the seven screws on the cover of the scanner control unit. 2 ADC064S E Open the cover of the scanner control unit. ADC011S F Remove the USB 2.0 interface board fixed with 6 screws.
Setting up the Scanner G Connect the IEEE1394 interface board to the extension connector. Fix the board with four accessory screws from inside, two accessory screws from outside. 2 ADC014S H Check that it is connected tightly, check that there are no foreign objects such as metal on the scanner control unit. I Close the scanner control unit cover and fix with seven screws, then insert the scanner control unit into the main unit.
Connecting to the Computer Connecting to the Computer This scanner can be connected to the computer with either a SCSI, USB, or IEEE1394 interface. An optional board will be required to connect with IEEE1394. Important ❒ Do not turn the power of the scanner ON before the software installation. If you run the "Found New Hardware Wizard" beforehand, you will not be able to install the software correctly.
Setting up the Scanner Setting the SCSI ID A Open the cover of the switch box on the lower left of the frontside of the scanner. 2 ADC015S Note ❒ Push the knob of the cover to the left and pull the cover to open. B Confirm the DIP Switch No.1 to the OFF position. ADC069S SCAM function is disabled. C Set the SCSI ID by rotating the Rotary Switch. ADC017S Note ❒ Press the Hard Reset Switch if you changed the SCSI ID while the power is ON. ⇒ p.
Connecting to the Computer Setting the SCSI ID Automatically Note ❒ If you use the SCSI board without SCAM function or the SCSI ID is overlapping with the other SCSI device, set the SCSI ID manually. A Open the cover of the switch box on the lower left of the frontside of the 2 scanner. ADC015S Note ❒ Push the knob of the cover to the left and pull the cover to open. B Set the DIP Switch No.1 to the ON position. ADC016S SCAM function is enabled.
Setting up the Scanner Connecting the SCSI Cable (When the Scanner is at the End of the Daisy Chain) A Shut down the computer and all of the SCSI connected devices. B Daisy chain the computer, scanner and SCSI connected devices. 2 ADC018S Note ❒ Connect the SCSI cable to either one side of the connectors. C Open the cover of the switch box on the lower left of the frontside of the scanner. ADC015S Note ❒ Push the knob of the cover to the left and pull the cover to open. D Set the DIP Switch No.
Connecting to the Computer Note ❒ Press the Hard Reset Switch if you changed the SCSI ID while the power is ON. ⇒ p.
Setting up the Scanner Connecting the SCSI Cable (When the Scanner is not at the End of the Daisy Chain) A Shut down the computer and all of the SCSI connected devices. B Daisy chain the computer, scanner and SCSI connected devices. 2 ADC020S C Open the cover of the switch box on the lower left of the frontside of the scanner. ADC015S Note ❒ Push the knob of the cover to the left and pull the cover to open. D Set the DIP Switch No.3 to the ON position. ADC021S Built-in SCSI terminator is disabled.
Connecting to the Computer Note ❒ Press the Hard Reset Switch if you changed the SCSI ID while the power is ON. ⇒ p.34 “Using the Hard Reset Switch” Using the Scanner only with the SCSI Connection You can set the scanner to the SCSI synchronous transmission for high-speed data transfer and shorten the total scan time. The USB and the optional IEEE1394 connection cannot be used when the SCSI synchronous transmission is set.
Setting up the Scanner Connecting with USB Interface Note ❒ Please use the recommended USB cable. Using other cables might occur an irregular operation. As for the recommended cables, please ask your service representative. 2 ❒ You can connect the scanner to two computers at the same time. One with the SCSI interface, and one with the USB 2.0 interface. Though, you cannot use the scanner at the same time from two computers.
Connecting to the Computer C Connect the USB cable to the USB connector. 2 ADC022S D Connect the other side of the cable to the USB connector on your computer. Connecting with IEEE1394 Interface Note ❒ The optional IEEE1394 interface board is required. ❒ An IEEE1394 cable is packed to be used for the optional IEEE1394 interface board. ❒ An irregular operation might occur for the IEEE1394 interface board of some PC. Please use the recommended IEEE1394 interface board for your PC.
Setting up the Scanner B Confirm the DIP Switch No.2 is in the ON position. 2 ADC080S Note ❒ If the DIP Switch No.2 is set to OFF, set it to ON. If the switch is set to OFF, "Found New Hardware Wizard" will not start. . ❒ Press the Hard Reset Switch if you changed the DIP Switch while the power is ON. ⇒ p.34 “Using the Hard Reset Switch” C Connect the IEEE1394 cable to the IEEE1394 connector. ADC023S Note ❒ Connect the cable to either one of the connectors.
Connecting to a Power Source Connecting to a Power Source This section explains how to connect this machine to a power source, using a bundled AC power cord. R WARNING: • Do not use with a power source with a voltage different from the specified voltage. Do not use a power outlet with multiple devices plugged in. These could create the risk of fire or electric shock. 2 • Avoid the use of an extension cord. • Do not damage, break, twist or modify the Power Cord.
Setting up the Scanner Important ❒ Be sure to remove the lock screws. Turning the power on without removing the screws could result not only in failure in scanning but in malfunction of this machine. C Confirm that the lock lever located on the back of the machine is set to the “Unlock” position. 2 ADC025S Important ❒ Be sure to set the lock lever to “Unlock”. Turning on the power with the lock lever set to “Lock” could result in failure in scanning or in malfunction of this machine.
Turning the Power On/Off Turning the Power On/Off Important ❒ Do not turn the power of the scanner ON before the software installation. If you run the “Found New Hardware Wizard” beforehand, you will not be able to install the software correctly. When the “Found New Hardware Wizard” started before the installation, click the [Cancel] button to discontinue the wizard. 2 ADC101S 1. Power Off 2.
Setting up the Scanner Using the Hard Reset Switch You need to hard reset the scanner when validate the settings of the DIP Switches or the Rotary Switch. To hard reset the scanner, you can turn off the scanner and turn it on again, or follow the procedures below. A Open the cover of the switch box on the lower left of the frontside of the 2 scanner. ADC015S Note ❒ Push the knob of the cover to the left and pull the cover to open. B Press the Hard Reset Switch.
3. Installing Software This machine can be used both as a TWAIN scanner and an ISIS scanner. A TWAIN driver and its applications are to be installed for the TWAIN scanner, and an ISIS driver and its applications are to be installed for the ISIS scanner. Installing TWAIN Driver When this machine is used as the TWAIN scanner; it is necessary to install the TWAIN driver to be used for the TWAIN compliant applications. Preparation Start installation, retaining the power of the scanner OFF.
Installing Software Installing TWAIN Driver Preparation Log on to the computer as a member of the Administrators group, for installation to Windows 2000/XP, Windows Server 2003, or Windows NT 4.0. A Start the computer, retaining the power of the scanner OFF. Note ❒ If the power of the computer turns ON, retaining the power of the scanner ON, before driver installation, the "Found New Hardware Wizard" automatically starts. In this case, click [Cancel] button.
Installing TWAIN Driver F In the Wizard, select [Search for a suitable driver for my device [recommended]], and continue the "Found New Hardware Wizard" to the end, according to the instruction on the display. Note ❒ When an instruction to set the Windows system CD-ROM appears on the display in the course of the installation, follow the instruction accordingly. ❒ Even when "No approval of the logo test" appears on the display, you can continue the installation by clicking [Continue].
Installing Software Installing DeskTopBinder Lite DeskTopBinder Lite is a software with which you can manage various types of file data, such as scanned images, or documents as if they were one file. This software is compatible with a TWAIN driver. You can use this software to scan documents with this scanner. System Requirements Install DeskTopBinder Lite to the computer that meets the system requirements below.
Installing DeskTopBinder Lite Installing DeskTopBinder Lite Preparation Log on to the computer as a member of the Administrators group, for installation to Windows 2000/XP, or Windows Server 2003. A Start Windows, and then insert the supplied CD-ROM labeled “Scanner Driver(s), Utilities and Operating Instructions” into the CD-ROM drive of the client computer. The CD-ROM Launcher screen appears.
Installing Software Installing ISIS Driver When this machine is used as the ISIS scanner; it is necessary to install the ISIS driver to be used for the ISIS compliant applications. Preparation Start installation, retaining the power of the scanner OFF. System Requirements 3 Install ISIS Driver to the computer that meets the system requirements below.
Installing ISIS Driver Installing ISIS Driver Preparation Log on to the computer as a member of the Administrators group, for installation to Windows 2000/XP, Windows Server 2003, or Windows NT 4.0. A Start the computer, retaining the power of the scanner OFF. Note ❒ If the power of the computer turns ON, retaining the power of the scanner ON, before driver installation, the "Found New Hardware Wizard" automatically starts. In this case, click [Cancel] button.
Installing Software F In the Wizard, select [Search for a suitable driver for my device [recommended]], and continue the "Found New Hardware Wizard" to the end, according to the instruction on the display. Note ❒ When an instruction to set the Windows system CD-ROM appears on the display in the course of the installation, follow the instruction accordingly. ❒ Even when "No approval of the logo test" appears on the display, you can continue the installation by clicking [Continue].
Installing QuickScan Installing QuickScan This software is compatible with a ISIS driver. You can use this software to scan documents with this scanner. System Requirements Install QuickScan to the computer that meets the system requirements below.
Installing Software 3 44
4. Setting Originals This chapter describes how to set an original to be scanned with this machine. It is possible to set an original on the exposure glass or the ADF. To scan several pages successively, using the ADF is convenient.
Setting Originals Original Sizes Available for Auto Detection The scanner can detect the following document sizes automatically. ❖ When the Background Panel is Black All of the original size can be detected from Exposure glass and ADF. ❖ When the Background Panel is White • When set on the Exposure glass Unable to detect automatically.
Sizes and Weights of Recommended Originals Originals that Require Special Care When scanning the following types of originals, be sure to follow the descriptions below. ❖ Originals that are difficult to detect the size automatically It is difficult for the scanner to automatically detect the sizes of the following types of originals, so select the original size manually.
Setting Originals Placing Originals Placing the Original on the Exposure Glass Important ❒ Be careful not to pinch your fingers when closing the ADF. A Lift the Pressure Panel. 4 ADC030S B With the side to be scanned facing down, place the original on the exposure glass, and align it with the home position and scale. ADC103S 1. Home position 2. Scale Important ❒ Do not press down on the exposure glass. Strong pressure on the exposure glass could cause it to break. C Gently lower the ADF.
Placing Originals Placing the Originals in the ADF The ADF allows you to place multiple originals at one time. ❖ Precautions when placing an original in the ADF • For information about the originals that cannot be placed in the ADF, see p.47 “Originals that cannot be set in the ADF”. • • • • Important ❒ Attempting to use unsuitable originals in the ADF can lead to a misfeed and damage to the originals. Place such originals directly on the exposure glass.
Setting Originals Important ❒ Do not hold the stopper to open the ADF. B Align the originals. To have the originals scanned in order, set the originals in order illustrated below. • Simplex scanning 4 ADC062S • Duplex scanning ADC063S C Fan the originals and align them well.
Placing Originals D Place the originals with first page on the top with the face up. Adjust the side guides to the size of your originals. ADC105S 4 1. Side guides Note ❒ Adjust the original guide carefully by moving the root part of the original guide located over the original tray ditch. ❒ Be careful not to drop any alien objects such as paper clip, dust, etc. into the original tray ditch. ❒ Check that the ADF is closed.
Setting Originals Changing the Color of the Background Panel Change the color of the Background Panel to enable auto original size detection or scan in clear images. Important ❒ Change the settings of the TWAIN driver from [Back.Panel] tab in [Initial Settings] of the driver dialog. ❒ Make sure that the color of the Background Panel for Exposure Glass, ADF and settings made in [Back.Panel] tab on the TWAIN driver are same.
Changing the Color of the Background Panel C Turn down blue levers on both sides. ADC036S The unit which stores the Background Panel for the ADF is drawn out. D Push down a lever on the left, and change the color of the Background Pan- 4 el by rotating the screw on the right to the ∆mark position. ADC037S Note ❒ Turn the slit in the way shown in the illustration. Do not turn to the other side. ❒ Turn the slit till you hear the click.
Setting Originals Changing the Color of the Background Panel for the Exposure Glass Note ❒ To change the color of the Background Panel for the Exposure Glass, reverse the panel. A Lift the Pressure Panel, and carefully pull out the Background panel that is fixed with magic tapes. 4 ADC071S B Place the Background Panel on the Exposure Glass, with the color to use downside. ADC072S Note ❒ Set the Background Panel so as to align the blue line at the Home position.
Changing the Color of the Background Panel C Align upper right of the Background Panel, with the home position for originals. ADC073S 4 1. Home position D Close the Pressure Panel slowly, and press it down firmly. ADC074S E Lift the Pressure Panel again, and press all over the Pressure Panel with a clean, soft cloth.
Setting Originals 4 56
5. Using the TWAIN Driver This chapter describes the operations for scanning originals with the TWAIN driver using DeskTopBinder Lite. In addition, some functions of the TWAIN driver are introduced. Procedure Breakdown The following overview diagram shows the flow of the steps for scanning documents from a computer using the TWAIN driver. Start a TWAIN-compliant application. Select and start the TWAIN driver. Menu may be different depending on the application you use.
Using the TWAIN Driver Scanning Originals This section explains how to scan originals using the TWAIN scanner function. The procedure goes along with p.57 “Procedure Breakdown”. A On the [Start] menu, point to [Program], point to [DeskTopBinder], and then click [DeskTopBinder]. DeskTopBinder Lite starts. B Click [Scanner Settings...] on the [Tools] menu. [Scanner Settings] dialog box appears. Note ❒ Check the settings in the [File format for scanned image(s)] area.
Scanning Originals I Click [Scan...] Note ❒ If you checked [Start from Scanner] on the TWAIN driver, press the {Start} } key after you clicked [Scan...]. The image is scanned. It will be displayed in the DeskTopBinder Viewer and the TWAIN driver dialog will close. Note ❒ With DeskTopBinder Lite, it is possible to edit and print scan files. For more information about how to edit and print, see DeskTopBinder Lite Help. J Save the scanned image in DeskTopBinder Lite. A On the [File] menu, click [Exit].
Using the TWAIN Driver What You Can Do with the TWAIN Driver The following is an introduction to the various functions of the TWAIN driver: Reference For more information about these functions or other functions, see TWAIN driver Help. Functions of the TWAIN Driver Functions 5 Explanation Scan Mode 4 Basic modes (Standard/Photo /OCR/Filing), User saved 100 scan modes You can call out and save the original Scan Modes. Orientation: Standard 0 deg. /Right 90 deg. /180 deg. /Left 90 deg.
What You Can Do with the TWAIN Driver Functions About Explanation Auto detect(Mixed-size) /Auto detect(Uni-size) /Various fixed form sizes /Custom size When the Background Panel is black, an optional width and length of originals will be automatically detected for both ADF and Exposure Glass by the [Auto detect(Mixed-size)] function. Double Feed Detect Ultrasonic Wave /Length /Ultrasonic Wave+Length /Off While using ADF, it detects and notes a double feeding.
Using the TWAIN Driver 5 62
6. Appendix Troubleshooting Error Indicators The following table shows the meaning of error indicators of this machine, and how to fix the errors. ADC112S Error description — — — — ❍ ❍ — ❍ ❍ ❍ Solution The ADF or ADF cover is not fully closed. Close the ADF or ADF cover. An original is jammed in the ADF. Remove the jammed original. More than one sheet of originals are fed to the ADF simultaneously, or incorrect feeding occurs. Remove the double feeding original.
Appendix When the Original is Jammed or Double Fed in the ADF When the original jammed in or double fed to the ADF, remove the original by the following procedure. A Open the ADF cover and remove if the original is jammed. ADC046S B Remove the original if it is jammed in the cove of the Original Table. 6 ADC047S Note ❒ You can easily remove the original by lifting the ADF a little. C Lift the ADF and remove if the original is jammed.
Troubleshooting D In case the jammed original is not found so far, follow the procedures below: A Take off the Background Panel. Reference ⇒ p.54 “Changing the Color of the Background Panel for the Exposure Glass” B Turn down blue levers on both sides. ADC036S The unit which stores the Background Panel for the ADF is drawn out. C Remove the jammed original. 6 ADC067S Note ❒ Regarding a small size original that cannot be set in the ADF, place it on the Exposure Glass instead. ⇒ p.
Appendix When the Originals are Not Fed Correctly A Remove the originals from the ADF. B Lift the Pressure Panel or open the ADF cover. ADC048S Unusual conditions of the Original Table will be corrected. C Shutdown the Pressure Panel or the ADF cover. 6 Note ❒ When you shut the ADF cover, please confirm the two magnets are fixed on the magnet catch and the cover is closed tightly. When Scanning is Not Performed as Expected Condition The scanned image is dirty.
Troubleshooting Condition Possible Cause and Required Action The scanned image is upside down. • The original was placed upside down. Place the original in the correct orientation, or set the [Orientation:] on the TWAIN driver to the correct setting. No image results from scanning. • The original was placed with the front and back reversed. • When the original is placed directly on the exposure glass, the side to be scanned must face down.
Appendix Message Possible Cause Error has occurred in the scanner. • There is an error in parameter setting to the scanner. Error has occurred in the scanner driver. • There is an error in the • Restart the operating system. driver, scanner, or in • If the same error occurs again, the operating system. please call the service representative. Required library module cannot be found. Please reinstall the module. • The library module has not been found.
Troubleshooting Message Cannot continue endorsing due to the limit. Possible Cause Required Action • The number of figures exceeded or dipped from the values set for the endorser counter. • The number of the counter has exceeded the value set in [Digit:] under the [Endorser] tab. Check the number of the originals and set [Start:], [Step:], and [Digit:]. • The number of the counter has reached -1 when you set [Step:] under the [Endorser] tab to negative value.
Appendix When in Installation and Other Problems Condition 6 70 Possible Cause Required Action The computer could not find the drivers even "Drivers and Utilities" CD-ROM is selected in the "Found New Hardware Wizard." • Wrong Installation of the hardware and the software. • First, install the TWAIN Driver from "Scanner Driver(s), Utilities and Operating Instructions" CD-ROM. Then start the "Found New Hardware Wizard." See p.35 “Installing Software” for details.
Cleaning Cleaning R WARNING: • Never remove any covers or screws other than those specified in this manual. The inside of the scanner contains high-voltage components that can cause electrical shock. Have all inspections, adjustments, and repairs inside the scanner performed by an authorized dealer only. • Do not attempt to modify this scanner in any way. Modification can cause fire or electrical shock. R CAUTION: • When disconnecting the power cord, always make sure to hold onto the plug.
Appendix Cleaning the Original Table Cove A Turn off the power of the scanner and unplug the power cord from the outlet. B Wipe all around the Feed Roller with a tightly wrung cloth, by turning the roller with your fingers. ADC106S 6 1. Feed Roller Note ❒ Always make sure to clean the Feed Roller after scanning a document written in pencil or other material that is not firmly fixed to the paper. Failure to clean the Feed Roller can cause soiling of the next document scanned.
Cleaning Cleaning Under the Pressure Panel A Turn off the power of the scanner and unplug the power cord from the outlet. B Lift the Pressure Panel. C Wipe the Background Panel, the ADF Exposure Glass 1, and the Exposure Glass with the cleaning cloth or a dry and soft cloth, taking a good care of the magic tapes not getting entangled in the cloth. 6 ADC107S 1. Background Panel for Exposure Glass 2. ADF Exposure Glass 1 3.
Appendix Cleaning Under the Background Panel Note ❒ The cleaning procedures below are not necessary for the simplex model. A Turn off the power of the scanner and unplug the power cord from the outlet. B Lift the Pressure Panel. C Take off the Background Panel. 6 ADC035S Reference ⇒ p.54 “Changing the Color of the Background Panel for the Exposure Glass” D Turn down blue levers on both sides.
Cleaning E Wipe the ADF Exposure Glass 2 with the cleaning cloth or a dry and soft cloth. ADC108S 1. ADF Exposure Glass 2 F Wipe the rollers with a tightly wrung cloth. 6 ADC053S 1. Rollers Reference Regarding how to set back the store box for the ADF Background Panel, please refer to the step E of p.52 “Changing the Color of the Background Panel for the ADF” Regarding how to set the Background Panel for the Exposure Glass, please refer to p.
Appendix Cleaning Inside the ADF Cover A Turn off the power of the scanner and unplug the power cord from the outlet. B Open the cover of the ADF. C Wipe the rollers with a tightly wrung cloth, by turning them with your fingers. 6 ADC110S 1. Rollers D Wipe the rollers in the cove with a tightly wrung cloth, by turning them with your fingers. ADC111S 1. Rollers Note ❒ When you shut the ADF cover, please confirm the two magnets are fixed on the magnet catch and the cover is closed tightly.
Cleaning Cleaning the Ventilation Panel Please clean the filter and the ventilation panel in every six months. However, please clean it properly when it gets dirty. A Turn off the power of the scanner and unplug the power cord from the outlet. B Open the ventilation cover panel on the left side of the ADF, and clean the inside filter and the ventilation panel.
Appendix Moving and Transporting the Scanner R CAUTION: • This scanner weighs approximately 72.8 lbs. • Make sure to lift it carefully with two persons or more so as to minimize physical strain. Careless lifting, reckless handling or allowing it to drop down can cause injury. • When transporting over long distances, please consult an authorized dealer. • Safety laws and regulations (including those stipulating radio wave regulations and material regulations) differ in each country.
Moving and Transporting the Scanner Transporting the Scanner A Turn on the Power Switch. Allow the scanner to remain on for at least 20 seconds, and then turn it off. B Set the Lock Lever on the left side of the scanner to the “Lock” position. ADC068S C Fix it with the two lock screws kept on the back of the Pressure Panel. A Lift the Pressure Panel, and carefully pull out the Background Panel that is fixed with the Velcro.
Appendix C Return the Background Panel to where it was. Reference Regarding how to set the Background Panel, please refer to the procedures B - E of p.54 “Changing the Color of the Background Panel for the Exposure Glass”. D Turn 90 degrees the caps that covered the holes for lock screws, and take out it. ADC087S Note ❒ The removed caps are to be kept in a bag and transported together with the machine, since they are used at the place where the machine is set up. 6 E Fix tightly with the lock screws.
Disposing of the Scanner Disposing of the Scanner When you want to dispose of your scanner, contact your dealer or a service representative.
Appendix How Data Size Changes Depending on Scan Area and Resolution Scan area and resolution determine the data size of a scanned data. The following general rules apply: • High resolution (dpi) makes data size larger and scan area smaller. • Large scan area makes data size larger and resolution (dpi) lower. Note ❒ In the following tables, each of the values displays the memory size to store as image data. Actual file sizes may vary depending on the file type setting (single page, PDF or multi-page TIFF).
How Data Size Changes Depending on Scan Area and Resolution When [Gray Scale] or [256 Colors] is Selected Scan Area 100dpi 200dpi 300dpi 400dpi 500dpi 600dpi 700dpi 800dpi A3 1,888 7,552 16,993 30,210 - - - - B4 1,416 5,664 12,744 22,656 - - - - A4 944 3,776 8,496 15,105 23,601 33,986 - - B5 708 2,832 6,372 11,328 17,700 25,488 - - A5 470 1,881 4,234 7,527 11,761 16,936 23,052 30,108 B6 352 1,410 3,173 5,642 8,815 12,694 17,278 22,568 A6 235 940 2,
Appendix When [16770K colors] is Selected Scan Area 6 100dpi 200dpi 300dpi 400dpi 500dpi 700dpi 800dpi A3 5,663 22,655 50,977 90,628 - - - - B4 4,247 16,989 38,231 67,964 - - - - A4 2,831 11,327 25,486 45,314 70,802 101,954 - - B5 2,123 8,495 19,113 33,982 53,100 76,460 - - A5 1,411 5,645 12,701 22,581 35,283 50,807 69,154 90,324 B6 1,057 4,230 9,519 16,925 26,446 38,079 51,832 67,701 A6 705 2,822 6,350 11,289 17,639 25,401 34,577 45,162 11
Options Options In this section, we refer to the options for this machine. Image Processing Unit Type B Installation of this option enables the following visual image processing by use of the TWAIN driver. ❖ Binary(Auto Image) When you binary-scan an original mainly with text files, this machine automatically detects and scans an appropriate threshold value. ❖ Binary(Text/Photo) Set when you scan an original consisting of both texts and photos.
Appendix Specifications Type flatbed type color scanner with ADF Scanning method Fixed document scanning and moving document scanning The duplex model enables scanning of both sides of an original simultaneously. Scanning area *1 ❖ ADF • One side color Main direction: 12 inch (297 mm) Max., 2.7 inch (69 mm) Min. Sub direction: 24.8 inch (630 mm) Max., 3.5 inch (90 mm) Min. • One side monochrome Main direction: 12 inch (297 mm) Max., 2.7 inch (69 mm) Min. Sub direction: 78.7 inch (2000 mm) Max., 3.
Specifications Power consumption During operation: 180 W During standby: 50 W During Low-Power mode: 8 W Warm-up time Max. 20 seconds Transition time to the Low-Power mode/ Recovery time from the Low-Power mode Transaction time: About 15 minutes Dimensions 19.3 inch × 27.4 inch × 13 inch (490 mm × 695 mm × 332 mm) (W × D × H) Weight Simplex Scanner: Approximately 68.3 lbs (31 kg) Recovery: 3 seconds or shorter Duplex Scanner: Approximately 72.
INDEX A ADF, 7 Jammed Originals, 64 Originals that cannot be set, 47 ADF Cover, 8 ADF Exposure Glass, 8 ADF Exposure Glass 1, 73 ADF Exposure Glass 2, 74 Auto Detection Original Sizes, 46 Automatic Document Feeder, 7 E Error Indicators, 63 Error Message and Required Action, 67 Error on the Original Table, 66 Exposure Glass, 8, 73 F Feed Roller, 72 Filter, 77 G B Background Panel for Exposure Glass, 8, 73 Background Panel for the ADF Changing the Color, 52 Background Panel for the Exposure Glass Changing
O Operating Instructions, 5 Options, 85 Originals Size, 45 Original Stopper, 7 Originals Weight, 45 Original Table, 7 Output Table, 7 P Placing Originals In the ADF, 49 On the Exposure Glass, 48 Power Connector, 8 Power Switch, 7 Pressure Panel, 8 T Transporting, 78 Troubleshooting, 63 Turning the Power On/Off, 33 TWAIN Driver Example of the Scanning, 58 Functions, 60 Installation, 35 Procedure Breakdown, 57 U USB 2.
MEMO 90 EN USA G418-8602
In accordance with IEC 60417, this machine uses the following symbols for the main power switch: a means POWER ON. b means POWER OFF.
Image Scanner Operating Instructions EN USA G418-8602
