4. Adding Toner and Staples This chapter explains how to replenish toner and staples when they run out. Adding Toner This section describes how to replace toner. • Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers in accordance with local regulations. 4 • Keep toner (used or unused) and toner containers out of reach of children.
4. Adding Toner and Staples • Always add toner when the machine instructs you. • Fault may occur if you use toner other than the recommended type. • When adding toner, do not turn off the operation switch. If you do, settings will be lost. • Do not repeatedly install and remove toner cartridges. This will result in toner leakage. • Do not shake the removed toner cartridge. Remaining toner might scatter. • If the message " Check toner cartridge replacement(s)." appears, the toner has almost run out.
Adding Toner Sending Faxes or Scanned Documents When Toner Has Run Out When the machine has run out of toner, the indicator on the display lights. Note that even if there is no toner left, you can still send faxes or scanned documents. • If number of communications executed after the toner has run out and not listed in the automatically output Journal exceeds 200, communication is not possible. 1. Make sure the machine is in facsimile or scanner mode. 2.
. Adding Toner and Staples Adding Staples This section describes what to do when staples need replacing. • Keep your hands clear of the booklet finisher tray when pulling out or pushing in the finisher's staple unit. You can trap your fingers if you do not. • Stapling failures or jams may occur if you use a staple cartridge other than that recommended. 4 • If you cannot pull out the upper unit, there are staples remaining inside the cartridge. Use all the staples, and do not add more.
Adding Staples 4 BBT023S Finisher SR790 This section describes how to add staples to the Finisher SR790.
4. Adding Toner and Staples 4 BBT024S Booklet Finisher SR3000 This section describes how to add staples to the Booklet Finisher SR3000.
Adding Staples 4 BBT025S Booklet Finisher SR3020 This section describes how to add staples to the Booklet Finisher SR3020.
4. Adding Toner and Staples 4 BAZ034S Booklet Finisher SR3020 This section describes how to add staples to the Booklet Finisher SR3020.
Adding Staples 4 BAZ035S Finisher SR3030 This section describes how to add staples to the Finisher SR3030.
4.
Replacing the Stamp Cartridge Replacing the Stamp Cartridge If the transmission stamp becomes faint, replace the cartridge. • This stamp cartridge is used for facsimile and scanner functions. • Do not add ink to the cartridge by yourself. Neglecting this can cause ink leakage. • Be sure not to dirty your fingers with ink from the cartridge. • Use the cartridge specified for this machine. Replacing the Stamp Cartridge (Type 1, 2) 4 1. Open the ADF unit. BBT007S 2. Open the stamp cover.
4. Adding Toner and Staples 3. Pull out the old stamp cartridge. BBT009S 4 4. Insert the new stamp cartridge. Insert the cartridge until the metal parts are no longer visible. BBT010S 5. Close the stamp cover. BBT011S 6. Close the ADF unit.
Replacing the Stamp Cartridge Replacing the Stamp Cartridge (Type 3, 4) 1. Open the ADF cover. 4 BBR012S 2. Raise lever P2, and then pull open cover P2. BBR013S 3. Push on the area of cover P3 marked “PUSH”, and then open the cover P3.
4. Adding Toner and Staples 4. Pull out the old stamp cartridge. BBR015S 4 5. Insert the new stamp cartridge. Push in the cartridge until the metal parts are no longer visible. BBR016S 6. Close cover P3, P2, and the ADF cover.
5. Entering Text This chapter describes how to enter characters. Entering Text This section explains how to enter text. When you enter a character, it appears at the position of the cursor. If there is a character already at the cursor position, the entered character appears before that. Available Characters This section explains which characters are available.
5. Entering Text 5 BJB030S • When entering uppercase or lowercase letters continuously, use [Shift Lock] to lock the case. • You can also use the number keys to enter numbers, regardless of mode. How to Enter Text This section explains text entry more specifically. Entering letters This section explains how to enter letters. 1. Press [Shift] to switch between uppercase and lowercase. 2. Press the letters you want to enter. Deleting characters This section explains how to delete characters. 1.
Entering Text Adding user text You can select and use a User Text that is registered in [Program / Change / Delete User Text]. For the registration procedure under Program / Change / Delete User Text, see “System Settings”, Network and System Settings Guide . 1. Press [User Text]. 5 2. Select the User Text you want to use.
5.
6. Operating Instructions This chapter describes the Operating Instructions of this machine. Installing Operating Instructions The supplied “Manuals” and “Manuals for Administrators” CD-ROMs contain HTML format manuals. For easy access, we recommend you install the manuals on a computer. • The “Manuals for Administrators” CD-ROM that includes Security Reference of the machine.
6. Operating Instructions PDF Manuals The supplied “Manuals” CD-ROM contains PDF manuals. File path The PDF manuals are in the following folder on the CD-ROM: MANUAL_PDF\ENGLISH • To view the PDF manuals, you need to have Adobe Acrobat Reader/Adobe Reader installed on your computer.
How to Use the Operating Instructions How to Use the Operating Instructions This section explains how to use manuals. 6 Opening from the Icon This section explains how to open a manual using its desktop icon. 1. Double-click the icon on your desktop. The browser opens and the manual appears. Opening from the [Start] Menu This section explains how to open a manual from the [Start] menu. 1.
6. Operating Instructions Opening from the CD-ROM This section explains how to open a manual from the supplied “Manuals” and “Manuals for Administrators” CD-ROMs. 1. Click [Read HTML manuals]. 2. Click the title of the manual you want to view. The browser opens, and then the manual appears.
7. Other User Tools Initial settings allow you to switch the language as well as checking the number of printed papers by displaying the counter. Changing the Display Language You can change the language used on the display. English is set as default. 1. Press the [User Tools/Counter] key. BBP015S 2. Press [Español]. 7 The language is changed to Spanish.
7. Other User Tools 3. Press [Salir]. The menu appears in Spanish.
Inquiry Inquiry The Inquiry function lets you check the telephone numbers to contact for repairs, or ordering consumables such as toner. Be sure to contact your service engineer to verify the following: Consumables • Telephone No. to order • Toner • Staple • Staple (Center) • TX Stamp Name Machine Maintenance/Repair • Telephone No. • Serial No. of Machine Sales Representative • Telephone No. 1. Press the [User Tools/Counter] key. 7 BBP015S 2. Press [Inquiry]. Inquiry information appears.
7. Other User Tools 3. Press [Print Inquiry List]. 4. Press the [Start] key. Inquiry information prints out. 5. Press [Exit] twice.
Changing Paper Thickness Settings Changing Paper Thickness Settings Select [Plain Paper 1] or [Plain Paper 2] depending on the type of plain paper. If in System Settings, [Tray Paper Settings], you set “Paper Thickness” to [Plain Paper] for each tray's [Paper Type], you must then select [Maintenance], [Plain Paper Setting] and specify either [Plain Paper 1] or [Plain Paper 2], depending on the thickness of the loaded paper. The default setting is Plain Paper 2.
7. Other User Tools 3. Press [Plain Paper Setting]. 4. Select the plain paper type for each tray depending on the paper to be set and press [OK]. 7 5. Press [Exit]. 6. Press [Exit]. • In System Settings, [Tray Paper Settings], for each tray's [Paper Type] you can specify [Plain Paper], [Middle Thick], [Thick Paper 1], [Thick Paper 2], or [Thick Paper 3]. For details about paper thickness, see “Recommended Paper Sizes and Types”. • p.
Counter Counter Displaying the Total Counter You can display the total counter value used for all functions. 1. Press the [User Tools/Counter] key. BBP015S 2. Press [Counter]. 7 3. To print a counter list, press [Print Counter List]. 4. Press the [Start] key. A counter list prints out.
7.
8. Remarks This chapter describes how to maintain and operate the machine. Dos and Don'ts The following items should be followed during use of this machine. • Keep the machine away from flammable liquids, gases, and aerosols. A fire or an electric shock might occur. • Unplug the power cord from the wall outlet before you move the machine. While moving the machine, you should take care that the power cord will not be damaged under the machine.
8. Remarks • Do not knock the machine while it is operating (for instance, do not use the machine's surfaces to knock stacks of paper into square). • Depending on the ambient temperature and humidity, steam may come from the exhaust vent behind the control panel during printing. This is water vapour from the paper, not a sign of malfunction. • If condensation forms inside the machine as a result of temperature change, the machine may not print properly.
Where to Put Your Machine Where to Put Your Machine This section describes precautions for installation and movement. Machine Environment Choose your machine's location carefully. Environmental conditions greatly affect its performance. Moving This section describes precautions when moving the machine. • Contact your service representative if you need to lift the machine (such as when relocating it to another floor).
8. Remarks • Protect the machine from strong shocks. Impact can damage the hard disk and cause stored files to be lost. As a precautionary measure, files should be copied to another computer. • p.73 "Turning On/Off the Power" Optimum environmental conditions This section describes precautions when locating the machine. • Keep the machine away from humidity and dust. Otherwise a fire or an electric shock might occur. • Do not place the machine on an unstable or tilted surface.
Where to Put Your Machine Access to the machine Place the machine near the power source, providing the clearance areas shown. BJB012S Type 1 and 2 1 Rear 10 cm (4 inches) or more 2 Right 55 cm (21.7 inches) or more 3 Front 75 cm (29.6 inches) or more 4 Left 10 cm (4 inches) or more Type 3 and 4 1 Rear 10 cm (4 inches) or more 2 Right 60 cm (23.7 inches) or more 3 Front 70 cm (27.6 inches) or more 4 Left 60 cm (23.
8. Remarks • Do not damage, break or make any modifications to the power cord. Do not place heavy objects on it. Do not pull it hard nor bend it more than necessary. These actions could cause an electric shock or fire. • If the power cord is damaged (exposure of the core, disconnection, etc.), contact your service representative to change a new one. Operating the machine with a damaged power cord may cause an electric shock or fire.
Maintaining Your Machine Maintaining Your Machine If the exposure glass, scanning glass, or ADF belt is dirty, copy clarity may be reduced. Clean these parts if they are dirty. • Do not use chemical cleaners or organic solvents, such as thinner or benzene. If such substances get inside the machine or melt plastic parts, a failure might occur. • Do not clean parts other than those explicitly specified in this manual. Other parts should only be cleaned by your service representative.
8. Remarks 2 1 BJA050S Clean 1 and 2. Cleaning the Dustproof Glass The dustproof glass may require cleaning if white lines appear on the print side of the document. • Do not insert the brush forcefully, or the machine might be damaged.
Maintaining Your Machine • Insert the cleaning stick so that its rubber surface is pointing down.
8.
9. Appendix This chapter describes the provided software and utilities CD-ROMs, specifications, and paper. Software and Utilities Included on the CD-ROM This section explains the software and utilities CD-ROMs provided with this machine. Two CD-ROMs come with this machine: “Printer Drivers and Utilities”, and “Scanner Driver and Utilities”. The following are included in these CD-ROMs: Font Manager For installing new screen fonts, or organizing and managing fonts already in the system.
9. Appendix • You can install the PCL printer drivers (PCL 5c and PCL 6), the RPCS printer driver, and the Adobe PostScript printer drivers from the CD-ROM provided with this machine or download them from the supplier's Web site. If your operating system is Windows XP x64/Vista x64, or Windows Server 2003/2003 R2 x64, you must download the printer drivers from the supplier's Web site. Select this machine and the operating system you are using, and then download them.
Software and Utilities Included on the CD-ROM Adobe PostScript Printer Drivers and PPD files Adobe PostScript printer drivers allow the computer to communicate with the printer using a printer language. PPD files allow the printer driver to enable specific printer functions. PPD files PPD files allow the printer driver to enable specific printer functions. • Some applications may require installation of the PCL 5c printer driver. In this case, you can install PCL 5c without having to install PCL 6.
9. Appendix • You can install the LAN-Fax driver from the CD-ROM provided with this machine or download it from the supplier's Web site. If your operating system is Windows XP x64/Vista x64, or Windows Server 2003/2003 R2 x64 you must download the LAN-Fax driver from the supplier's Web site. Select this machine and the operating system you are using, and then download it. This driver is required to use LAN-Fax functions.
Software and Utilities Included on the CD-ROM System requirements • Hardware PC/AT-compatible machines that support the operating system properly • Operating system • When installing all functions of DeskTopBinder: Windows 2000 Professional SP1 or later/2000 Server SP1 or later/2000 Advanced Server SP1 or later/XP Professional/XP Home Edition • When installing only SmartDeviceMonitor for Client: Windows 2000 Professional SP1 or later/2000 Server SP1 or later/XP Professional/XP Home Edition SmartDeviceMoni
9.
Software and Utilities Included on the CD-ROM • DeskTopBinder includes SmartDeviceMonitor for Client. See Help of DeskTopBinderSmartDeviceMonitor for Client.
9. Appendix Specifications for the Main Unit This section describes specifications for the main unit.
Specifications for the Main Unit Copy paper size: • Trays: A3 - A5 , 11 × 17 • Bypass: A3 mm) - 81/2 × 11 - A6 , 12 × 18 , 8K (267 × 390 mm) , 16K (195 × 267 mm) - 51/2 × 81/2 , 8K (267 × 390 mm) , 16K (195 × 267 • Bypass (custom size): Vertical: 90.0 - 305.0 mm, 3.6 - 12.1 inches Horizontal: 148.0 - 600.0 mm, 5.83 - 23.7 inches • Duplex: A3 mm) - A5 , 11 ×17 - 81/2 × 11 , 8K (267 × 390 mm) , 16K (195 × 267 Paper weight: • Trays: 60.0 - 256.0 g/m2, 16 lb. - 68 lb. • Bypass: 60.0 - 256.
9. Appendix Metric version Inch version 400% 400% 200% 200% 141% 155% 122% 129% 115% 121% • Full size Metric version 100% Inch version 100% • Reduction Metric version 9 Inch version 93% 93% 82% 85% 75% 78% 71% 73% 65% 65% 50% 50% 25% 25% Zoom: From 25 to 400% in increments of 1% Maximum continuous copy run: 999 sheets Paper capacity (80 g/m2, 20 lb.
Specifications for the Main Unit Power consumption: • Main unit only Type 1 Type 2 Warm-up 1440 W 1440 W Stand-by 204 W 204 W During printing 737 W 795 W Maximum 1440 W 1440 W • Complete system Type 1 Type 2 Warm-up 1440 W 1440 W Stand-by 222 W 222 W During printing 824 W 883 W Maximum 1440 W 1440 W • The complete system consists of the main unit, Booklet Finisher SR3000, large capacity tray, file format converter, IEEE 802.
9. Appendix Type 1 Type 2 Stand-by Less than 39.7 dB (A) Less than 39.7 dB (A) Copying Less than 69.5 dB (A) Less than 70.3 dB (A) • Sound pressure level: • Main unit only Type 1 Type 2 Stand-by Less than 29.1 dB (A) Less than 29.1 dB (A) Copying Less than 50.6 dB (A) Less than 50.6 dB (A) • Complete system Type 1 Type 2 Stand-by Less than 26.5 dB (A) Less than 26.5 dB (A) Copying Less than 55.2 dB (A) Less than 56.
Specifications for the Main Unit Photosensitivity type: OPC drum Original scanning: One-dimensional solid scanning system through CCD Copy process: Dry electrostatic transfer system Development: Dry two-component magnetic brush development system Fusing: Induction Heating (IH) fusing Scan resolution: • 600 dpi × 600 dpi Copy/Print resolution: • 600 dpi × 600 dpi • 1200 dpi × 1200 dpi (for printer function only) Exposure glass: Stationary original exposure type Original reference position: Rear left corner
9. Appendix • Duplex: A3 mm) - A5 , 11 × 17 - 81/2 × 11 , 8K (267 × 390 mm) , 16K (195 × 267 Paper weight: • Trays: 60.0 - 256.0 g/m2, 16 lb. - 68 lb. • Bypass: 60.0 - 256.0 g/m2, 16 lb. - 68 lb. • Duplex: 60.0 - 169.0 g/m2, 16 lb. - 45 lb. For details about and recommendations concerning thick paper, see “Thick Paper”. Non-reproduction area (Copier): • Leading edge: 3.7 - 6.7 mm, 0.15 - 0.26 inches (2.7 - 5.7 mm, 0.10 - 0.22 inches for paper heavier than 81 g/m2, 22.0 lb.) • Trailing edge: 0.5 - 6.
Specifications for the Main Unit • Full size Metric version Inch version 100% 100% • Reduction Metric version Inch version 93% 93% 82% 85% 75% 78% 71% 73% 65% 65% 50% 50% 25% 25% • Zoom: From 25 to 400% in increments of 1% Maximum continuous copy run: 999 sheets Paper capacity (80 g/m2, 20 lb.): • Tray 1, 2: 550 sheets 9 • Bypass tray: 100 sheets Power source: 120 V, 60 Hz, 12 A or more Please be sure to connect the power cord to a power source as above.
9. Appendix Type 3 Maximum 1440 W Type 4 1440 W • Complete system Type 3 Type 4 Warm-up 1440 W 1440 W Stand-by 151 W 151 W During printing 1123 W 1223 W Maximum 1440 W 1440 W • The complete system consists of the main unit, Booklet Finisher SR3020, large capacity tray (LCT), fax unit, and printer/scanner unit. Dimensions (W × D × H up to exposure glass): Types 3, 4: 670 × 677 × 760 mm, 26.4 × 26.7 × 30.0 inches Space for main unit (W × D): Types 3, 4: 1,065 × 677 mm, 42.0 × 26.
Specifications for the Main Unit Type 3 Type 4 Stand-by Less than 21.6 dB (A) Less than 21.6 dB (A) Copying Less than 54.0 dB (A) Less than 54.5 dB (A) • Complete system Type 3 Type 4 Stand-by Less than 20.6 dB (A) Less than 20.9 dB (A) Copying Less than 57.9 dB (A) Less than 58.0 dB (A) • Sound power level and sound pressure level are actual values measured in accordance with ISO 7779. • Sound power level and sound pressure level are measured from the position of the bystander.
9. Appendix Maximum number of stored documents: Maximum: 1,000 (The maximum number of received faxes that can be stored is 400.) Number of Pages Supported by Memory Sorting: Maximum: 1,000 pages Copier/Black-and-white mode/A4 original: about 1,000 Printer/Black and white/A4/600 dpi, 2 bits: about 1,000 (Under the printer function, the number of the pages that can be sorted depends on the print image.) Document Server for Type 3 and 4 HDD (Document Server): Approx.
Specifications for Auto Document Feeder Specifications for Auto Document Feeder This section describes specifications for auto document feeder. Specifications for Auto Document Feeder (ARDF DF3030) This section describes specifications for auto document feeder ARDF DF 3030.
9. Appendix Mode: ADF mode, Batch mode, SADF mode, Mixed Size mode, Custom Size originals mode Original size: • Metric version: • 1-sided originals: A3 - B6 JIS (Japanese Industrial Standard) • 2-sided originals: A3 - A5 • Inch version: • 1-sided originals: 11 × 17 - 51/2 × 81/2 • 2-sided originals: 11 × 17 - 51/2 × 81/2 Original weight: • 1-sided originals: 40 - 128 g/m2 (10 - 34 lb.) • 2-sided originals: 52 - 128 g/m2 (14 - 34 lb.) Number of originals to be set: 100 sheets (80 g/m2, 20 lb.
Specifications for Finishers (Optional) Specifications for Finishers (Optional) This section describes specifications for finishers. Specifications for Finisher SR790 (1000-sheet) (Optional) This section describes specifications for the Finisher SR790. Finisher Upper Tray This section describes specifications for the finisher upper tray of the Finisher SR790.
9. Appendix Staple paper size: A3 , B4 JIS , A4 , B5 JIS , 11 × 17 , 11 × 15 , 11 × 14 , 10 × 15 , 10 × 14 , 1 1 1 8 /2 × 14 , 8 /4 × 14 , 8 /2 × 13 , 81/4 × 13 , 8 × 13 , 81/2 × 11 , 8 × 101/2 , 8 × 10 , 71/4 × 101/2 Staple paper weight: 64 - 90 g/m2, 17 - 28 lb. Staple capacity (80 g/m2, 20 lb.): • 50 sheets: A4, 81/2 × 11 or smaller • 30 sheets: B4 JIS, 81/2 × 14 or larger Stack capacity after stapling (80 g/m2, 20 lb.
Specifications for Finishers (Optional) 81/4 × 14 , 81/4 × 13 , 8 × 13 , 8 × 101/2 , 8K , 16K , custom size , 8 × 10 , 51/2 × 81/2 , 71/4 × 101/2 Paper weight: 52 - 163 g/m2, 14 - 43 lb. Stack capacity (80 g/m2, 20 lb.): • 250 sheets: A4, 81/2 × 11 or smaller • 50 sheets: B4 JIS, 81/2 × 14 or larger Finisher Shift Tray This section describes specifications for the finisher shift tray of the Finisher SR3030.
9. Appendix • 30 sheets: A3 / A4 , B4 JIS / B5 JIS , 11 × 17 /81/2 × 11 Stack capacity after stapling (80 g/m2, 20 lb.
Specifications for Finishers (Optional) Staple paper size: A3 , B4 JIS , A4 , B5 JIS , 11 × 17 , 11 × 15 , 11 × 14 , 10 × 15 , 10 × 14 , 1 1 1 8 /2 × 14 , 8 /4 × 14 , 8 /2 × 13 , 81/2 × 11 , 81/4 × 13 , 8 × 13 , 8 × 101/2 1 1 , 8 × 10 , 7 /4 × 10 /2 Staple paper weight: 52 - 253 g/m2, 14 - 67.5 lb. Staple capacity (80 g/m2, 20 lb.
9. Appendix Specifications for Booklet Finisher (Optional) This section describes specifications for booklet finisher. Specifications for Booklet Finisher SR3020 (2000-sheet-Booklet) (Optional) This section describes specifications for Booklet Finisher SR3020. Finisher Upper Tray This section describes specifications for the finisher upper tray of Booklet Finisher SR3020.
Specifications for Booklet Finisher (Optional) • 500 sheets: A5 • 100 sheets: A5 , B6 JIS , A6 , 51/2 × 81/2 Staple paper size: A3 , B4 JIS , A4 , B5 JIS , 12 × 18 , 11 × 17 , 11 × 15 , 11 × 14 , 10 × 15 , 10 1 1 × 14 , 8 /2 × 14 , 8 /4 × 14 , 81/2 × 13 , 81/4 × 13 , 8 × 13 , 81/2 × 11 , 8 × 101/2 , 8 × 10 , 71/4 × 101/2 , 8K , 16K Staple paper weight: 64 - 90 g/m2, 17 - 24 lb. Staple capacity (80 g/m2, 20 lb.
9. Appendix Saddle stitch capacity (80 g/m2, 20 lb.): 1 set: 15 sheets Stack capacity after saddle stitching (80 g/m2, 20 lb.): • 2 - 5 sheets: 30 sets • 6 - 10 sheets: 15 sets • 11 - 15 sheets: 10 sets Saddle stitch position: Center 2 positions Power consumption: Approx. 96 W (Power is supplied from the main unit.) Dimensions (W × D × H): 657 × 613 × 960 mm, 25.8 × 24.2 × 37.8 inches Weight: • Approx. 63 kg, 138.9 lb. (without punch kit) • Approx. 65 kg, 143.3 lb.
Specifications for Booklet Finisher (Optional) Paper size: A3 , B4 JIS , A4 , B5 JIS , 11 × 17 , 81/2 × 14 , 81/2 × 13 , 81/2 × 11 1 13 , 8 × 13 , 7 /4 × 101/2 , 81/4 × Paper weight: 52 - 256 g/m2, 14 - 68 lb. Stack capacity (80 g/m2, 20 lb.): • 1,000 sheets: A4, 81/2 × 11 or smaller • 500 sheets: B4 JIS, 81/2 × 14 or larger Staple paper size: A3 , B4 JIS , A4 , B5 JIS , 11 × 17 , 81/2 × 14 , 81/2 × 11 1 1 8 × 13 , 8 /2 × 13 , 8 /4 × 13 , 71/4 × 101/2 , Staple paper weight: 64 - 90 g/m2, 17 - 24 lb.
9. Appendix Saddle stitch capacity (80 g/m2, 20 lb.): 1 set: 10 sheets Stack capacity after saddle stitching (80 g/m2, 20 lb.): • 2 - 5 sheets: 20 sets • 6 - 10 sheets: 10 sets Saddle stitch position: Center 2 positions Power consumption: Approx. 60 W (Power is supplied from the main unit.) Dimensions (W × D × H): 535 × 600 × 930 mm, 21.1 × 23.7 × 36.7 inches Weight: • Approx. 48 kg, 105.9 lb. (without punch kit) • Approx. 50 kg, 110.3 lb.
Specifications for Punch Kit (Optional) Specifications for Punch Kit (Optional) This section describes specifications for punch kit. Specifications for Punch Kit (Finisher SR3030, Booklet Finisher SR3020) (Optional) This section describes specifications for the punch kit (Finisher SR3030, Booklet Finisher SR3020).
9. Appendix Punch unit type 2 & 3 holes type: 3 holes 2 & 3 holes type: 3 holes Paper size : A3, B4 JIS, 11 × 17, 11 × 15, 11 × 14, 10 × 15, 10 × 14, 71/4 × 101/2, 8K : A4, B5 JIS, 81/2 × 11, 8 × 101/2, 8 × 10, 1 4 × 10 /2, 16K 71/ Paper weight: 52 - 105 g/m2, 14 - 28 lb. Power consumption: 20 W (Power is supplied from the main unit.) Dimensions (W × D × H): 110 × 484 × 117 mm, 4.4 × 190.6 × 46.1 inches Weight: Approx. 2.9 kg, 6.4 lb.
Specifications for Punch Kit (Optional) Punch unit type Paper size 2 & 3 holes type: 2 holes : A3, B4 JIS, A4, B5 JIS, A5, 11 × 17, 81/2 × 14, 81/2 × 11, 51/2 × 81/2, 71/4 × 101/2, 8 × 13, 81/2 × 13, 81/4 × 13 2 & 3 holes type: 2 holes : A4, B5 JIS, A5, 81/2 × 11, 71/4 × 101/2, 51/2 × 81/2 2 & 3 holes type: 3 holes : A3, B4 JIS, 11 × 17 2 & 3 holes type: 3 holes : A4, B5 JIS, 81/2 × 11, 71/4 × 101/2 Paper weight: 52 - 105 g/m2, 14 - 28 lb.
9. Appendix Specifications for Paper Trays (Optional) This section describes specifications for paper trays. Specifications for Lower Paper Tray (Optional) This section describes specifications for the lower paper tray. Paper size: A3 , B4 JIS , A4 , B5 JIS , A5 , 11 × 17 , 81/2 × 14 , 81/2 × 11 , 81/2 × 13 1 1 1 1 1 1 , 8 /4 × 13 , 8 × 13 , 5 /2 × 8 /2 , 7 /4 × 10 /2 , 8 /4 × 14 , 8 × 101/2 ,8 × 10 , 11 × 15 , 10 × 14 Paper weight: 60 - 256 g/m2, 16 - 68 lb. Paper capacity (80 g/m2, 20 lb.
Specifications for Paper Trays (Optional) Dimensions (W × D × H): 580 × 620 × 260 mm, 22.9 × 25.6 × 10.3 inches Weight: Approx. 26 kg, 57.4 lb. Specifications for Tray 3 (LCT) (Optional) This section describes specifications for the tray 3 (LCT). Paper size: A4 , 81/2 × 11 Paper weight: 60 - 256 g/m2, 16 - 68 lb. Paper capacity (80 g/m2, 20 lb.): 1,000 sheets × 2 trays Power consumption: Maximum 50 W (Power is supplied from the main unit.) Dimensions (W × D × H): 580 × 650 × 260 mm, 22.9 ×25.6 × 10.
9. Appendix Weight: Approx. 14 kg, 30.9 lb.
Specifications for Bridge Unit (Optional) Specifications for Bridge Unit (Optional) This section describes specifications for the bridge unit. Stack capacity (80 g/m2, 20 lb.): • 250 sheets: A4, 81/2 × 11 or smaller • 125 sheets: B4 JIS, 81/2 × 14 or larger Power consumption: Approx. 10 W (Power is supplied from the main unit.) Dimensions (W × D × H): 415 × 412 × 111 mm, 16.4 × 16.3 × 4.4 inches Weight: Approx. 4 kg, 8.9 lb.
9. Appendix Specifications for Internal Tray 2 (Optional) This section describes specifications for the internal tray 2 (1 bin tray). Number of bins: 1 Paper size: A3 , B4 JIS , A4 , B5 JIS , A5 , 11 × 17 , 81/2 × 14 , 81/2 × 11 , 51/2 × 81/2 , 71/4 × 101/2 , 81/2 × 13 , 81/4 × 14 , 81/4 × 13 , 8 × 13 , 8 × 10 , 11 × 14 , 11 × 15 , 10 × 14 , 10 × 15 , 8K , 16K , custom size Paper weight: 60 - 105 g/m2, 16 - 28 lb. Paper capacity (80 g/m2, 20 lb.): 125 sheets Power consumption: Approx.
Specifications for Internal Shift Tray (Optional) Specifications for Internal Shift Tray (Optional) This section describes specifications for the shift sort tray. Paper capacity (80 g/m2, 20 lb.): • 250 sheets: A4, 81/2 × 11 or smaller • 125 sheets: B4 JIS, 81/2 × 14 or larger Power consumption: Maximum 10 W (Power is supplied from the main unit.) Dimensions (W × D × H): 423 × 468 × 114 mm, 16.7 × 18.5 × 4.5 inches Weight: Approx. 2 kg, 4.5 lb.
9. Appendix Specifications for IEEE 1284 Interface Board (Optional) This section describes specifications for the IEEE 1284 interface board. Transmission spec.
Specifications for Wireless LAN Board (Optional) Specifications for Wireless LAN Board (Optional) This section describes specifications for the wireless LAN board. Transmission spec.: • Based on IEEE 802.11a/b/g (wireless LAN) Protocol: TCP/IP, IPX/SPX, AppleTalk Data transfer speed: Auto select from the following speed: 1 Mbps, 2 Mbps, 5.5 Mbps, 6 Mbps, 9 Mbps, 11 Mbps, 12 Mbps, 18 Mbps, 24 Mbps, 36 Mbps, 48 Mbps, 54 Mbps Frequency range: • IEEE 802.
9. Appendix Specifications for Bluetooth Interface Unit (Optional) This section describes specifications for the Bluetooth interface unit. Supported Profiles: • SPP (Serial Port Profile) • HCRP (Hardcopy Cable Replacement Profile) • BIP (Basic Imaging Profile) Frequency Range: 2.45 GHz ISM band Data Transmission Speed: 723 kbps Maximum Range: 10 m • The transmission speed is adjusted according to factors such as the distance and obstacles between the devices, radio signal condition and Bluetooth adaptor.
Specifications for Gigabit Ethernet (Optional) Specifications for Gigabit Ethernet (Optional) This section describes specifications for the Gigabit Ethernet.
9. Appendix Specifications for Other Options This section describes specifications for other options. Copy Data Security Unit The Copy Data Security Unit deletes images and prints the gray ground color of the paper when the documents marked unauthorized are copied. DataOverWriteSecurity Unit The DataOverWriteSecurity Unit automatically overwrites the data that remains on the hard disk.
Trademarks Trademarks Adobe, Acrobat, Acrobat Reader, PostScript, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. AppleTalk, Macintosh and Mac OS are registered trademarks of Apple Inc. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Ricoh Company, Ltd. is under license.
9.
INDEX About the guide on the internal tray 2.................56 Access to the machine........................................135 Adding staples.....................................................104 Adding toner........................................................101 Address book.........................................................17 ADF...................................................20, 51, 54, 159 Adhesive labels.....................................................88 Adjusting colors..........
Enlarge...................................................................11 Enter key (# key)...................................................64 Entering letters.....................................................116 Entering text................................................115, 116 Entry screen.........................................................115 Envelope................................................................49 Envelopes........................................................
Large capacity tray...............................................20 Large capacity tray (LCT)..................58, 59, 79, 90 LCT...................................................................20, 90 Legal prohibition.................................................... 19 Loading paper.......................................................77 Loading paper into the large capacity tray (LCT)... ................................................................................
Printer driver............................................68, 70, 141 Printer Drivers and Utilities........141, 143, 145, 146 Printer Utility for Mac..........................................141 Printing a PDF file directly.....................................12 Printing with the finisher.........................................12 Program key...........................................................63 Punch................................................................11, 12 Punch Kit.....................
Start key.................................................................64 Stored Print.............................................................12 Storing paper.........................................................99 Storing received documents.................................13 Symbols..................................................................20 System Reset..........................................................72 Wireless LAN board.....................................60, 181 T Text....
MEMO 192 EN USA D029-7604 Draft 2008/06/09
Copyright © 2008 Draft 2008/06/09
Operating Instructions About This Machine Type for C2828/MP C2800/LD528C/Aficio MP C2800 Type for C3333/MP C3300/LD533C/Aficio MP C3300 Type for C4040/MP C4000/LD540C/Aficio MP C4000 Type for C5050/MP C5000/LD550C/Aficio MP C5000 Type for C2828G/LD528CG/Aficio MP C2800G Type for C3333G/LD533CG/Aficio MP C3300G Type for C4040G/LD540CG/Aficio MP C4000G Type for C5050G/LD550CG/Aficio MP C5000G EN USA D029-7603 Draft 2008/06/09
